Changes for page End Device Frequency Band

Last modified by Edwin Chen on 2024/10/21 20:35
<
From version < 3.5 >
edited by Xiaoling
on 2022/05/10 15:33
To version < 10.1 >
edited by Xiaoling
on 2022/05/30 10:39
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,8 +1,11 @@
1 1  (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %)
2 -
2 + **Contents：**
3 3  
4 4  {{toc/}}
5 5  
6 +
7 +
8 +
6 6  = 1. Introduction =
7 7  
8 8  This page list the default frequency band for Dragino End Devices. The frequency bands are base on TTN Frequency Bands. User can modify upgrade firmware to support different frequency band or use AT Command to change the sub band in some frequency bands.
... ... @@ -10,15 +10,21 @@
10 10  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
11 11  * Frequency Bands vs Country List : Page 11 of [[LoRaWAN Regional Parameters RP2-1.0.3>>url:https://resources.lora-alliance.org/technical-specifications/rp2-1-0-3-lorawan-regional-parameters]]
12 12  
16 +
17 +
13 13  = 2. OTAA Join Behaviour =
14 14  
15 15  For 005 LoRaWAN stack: to save battery, once boot, device will make first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again.
16 16  
22 +(((
17 17  For 005 LoRaWAN Stack:
24 +)))
18 18  
19 19  * EU868 OTAA Join DR select. SF7->SF8->SF9->SF10->SF11->SF12; Each 3 attempts and then loop
20 20  * US915 and AU915 OTAA Join procedure,. End node by default will use all 72 channels to join and it will be set to use the proper sub-band after Join success
21 21  
29 +
30 +
22 22  = 3. Default Frequency Bands =
23 23  
24 24  
... ... @@ -26,12 +26,15 @@
26 26  
27 27  === 3.1.1 Notice for AS923 Frequency Bands ===
28 28  
38 +(((
29 29  Since [[RP002-1.0.1LoRaWAN Regional Parameters>>url:https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf]], AS923 include three different default settings for different countries: AS923-1, AS923-2 and AS923-3.
40 +)))
30 30  
42 +(((
31 31  AS923-1 use the same default uplink frequency as previous AS923 firmware. AS923-2 and AS923-3 are new with different default uplink frequency. User need to know exactly the frequency bands from the LoRaWAN server and choose the right firmware version for the end node.
44 +)))
32 32  
33 33  
34 -
35 35  === 3.1.2 AS920-923 & AS923-925 : AS923-1 (AS923) ===
36 36  
37 37  * Default Uplink channel:
... ... @@ -59,6 +59,7 @@
59 59  ** Uplink channels 1-8 (RX1)
60 60  ** 923.2 - SF10BW125 (RX2)
61 61  
74 +
62 62  === 3.1.3 AS923-2 ===
63 63  
64 64  * Default Uplink channel:
... ... @@ -71,6 +71,7 @@
71 71  ** Uplink channels 1-8 (RX1)
72 72  ** 921.4 - SF10BW125 (RX2)
73 73  
87 +
74 74  === 3.1.4 AS923-3 ===
75 75  
76 76  * Default Uplink channel:
... ... @@ -83,6 +83,7 @@
83 83  ** Uplink channels 1-8 (RX1)
84 84  ** 916.6 - SF10BW125 (RX2)
85 85  
100 +
86 86  === 3.1.5 AS923-4 ===
87 87  
88 88  * Countries : Israel
... ... @@ -95,6 +95,7 @@
95 95  ** Uplink channels 1-8 (RX1)
96 96  ** 917.3 - SF10BW125 (RX2)
97 97  
113 +
98 98  == 3.2 AU915-928(AU915) ==
99 99  
100 100  **Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]** , Default use CHE=2
... ... @@ -120,15 +120,29 @@
120 120  ** 927.5 - SF7BW500 to SF12BW500
121 121  ** 923.3 - SF12BW500(RX2 downlink only)
122 122  
139 +(((
123 123  There is a issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only works for the LoRaWAN server use sub-band2 , such as TTN. To solve this, user need to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvinient.
141 +)))
124 124  
143 +
144 +(((
125 125  So since **Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]**, To make sure the end node supports all sub band by default. In the OTAA Join process, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join.
146 +)))
126 126  
148 +
149 +(((
127 127  After Join success, the end node will switch to the correct sub band by:
151 +)))
128 128  
129 -* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
130 -* Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
153 +* (((
154 +Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
155 +)))
156 +* (((
157 +Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
131 131  
159 +
160 +)))
161 +
132 132  == 3.3 CN470-510 (CN470) ==
133 133  
134 134  Used in China, Default use CHE=1
... ... @@ -154,6 +154,7 @@
154 154  ** 508.1 - SF7BW125 to SF12BW125
155 155  ** 505.3 - SF12BW125 (RX2 downlink only)
156 156  
187 +
157 157  == 3.4 EU863-870 (EU868) ==
158 158  
159 159  * Uplink:
... ... @@ -185,6 +185,7 @@
185 185  ** Uplink channels 1-3 (RX1)
186 186  ** 866.550 - SF10BW125 (RX2)
187 187  
219 +
188 188  == 3.6 KZ865 ==
189 189  
190 190  * Uplink ~-~- 125Khz , DR0 - DR5
... ... @@ -198,6 +198,7 @@
198 198  ** The RX1 receive window uses the same channel as the preceding uplink.
199 199  ** The RX2 receive window uses a fixed frequency and data rate. The default parameters are 866.7MHz / DR0 (SF12, 125 kHz)​
200 200  
233 +
201 201  == 3.7 KR920-923 (KR920) ==
202 202  
203 203  * Default channel:
... ... @@ -218,8 +218,11 @@
218 218  ** Uplink channels 1-7(RX1)
219 219  ** 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
220 220  
254 +
221 221  == 3.8 MA869 ==
222 222  
257 + Country: Morroco
258 +
223 223  * Uplink:
224 224  ** 869.1 - SF7BW125 to SF12BW125
225 225  ** 869.3 - SF7BW125 to SF12BW125
... ... @@ -235,10 +235,12 @@
235 235  ** Uplink channels 1-9 (RX1)
236 236  ** 869.525 - SF12BW125 (RX2 downlink only)
237 237  
274 +
238 238  == 3.9 US902-928 (US915) ==
239 239  
240 240  Used in USA, Canada and South America.
241 241  
279 +
242 242  === 3.9.1 Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]. ===
243 243  
244 244  Default use CHE=2, Subband 2
... ... @@ -266,13 +266,27 @@
266 266  
267 267  === 3.9.2 Latest firmware, Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]] ===
268 268  
307 +(((
269 269  There is an issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only work for the LoRaWAN server use sub-band2 , such as TTN. To solve this, the user needs to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvenient.
309 +)))
270 270  
311 +(((
312 +
313 +)))
314 +
315 +(((
271 271  So since **Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]**, we have improved this, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join, In this case, In this case, the end node can support LoRaWAN servers with different subbands. To make sure the end node will only transmit the proper sub-band after OTAA Joined successfully, the end node will:
317 +)))
272 272  
273 -* Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that subband
274 -* Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include)
319 +* (((
320 +Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that subband
321 +)))
322 +* (((
323 +Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include)
275 275  
325 +
326 +)))
327 +
276 276  = 4. Frequency Bands for different server =
277 277  
278 278  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0