Changes for page End Device Frequency Band

Last modified by Edwin Chen on 2024/10/21 20:35
<
From version < 11.9 >
edited by Xiaoling
on 2022/06/01 11:47
To version < 16.1 >
edited by Edwin Chen
on 2023/12/07 09:47
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.Edwin
Content
... ... @@ -1,5 +1,5 @@
1 1  (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %)
2 - **Contents：**
2 + **Table of** **Contents：**
3 3  
4 4  {{toc/}}
5 5  
... ... @@ -8,33 +8,31 @@
8 8  
9 9  = 1. Introduction =
10 10  
11 +
11 11  This page list the default frequency band for Dragino End Devices. The frequency bands are base on TTN Frequency Bands. User can modify upgrade firmware to support different frequency band or use AT Command to change the sub band in some frequency bands.
12 12  
13 13  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
14 14  * Frequency Bands vs Country List : Page 11 of [[LoRaWAN Regional Parameters RP2-1.0.3>>url:https://resources.lora-alliance.org/technical-specifications/rp2-1-0-3-lorawan-regional-parameters]]
15 15  
16 -
17 -
18 18  = 2. OTAA Join Behaviour =
19 19  
20 -For 005 LoRaWAN stack: to save battery, once boot, device will make first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again.
21 21  
20 +Since 005 LoRaWAN stack: to save battery, once boot, device will first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again.
21 +
22 22  (((
23 -For 005 LoRaWAN Stack:
23 +Since 005 LoRaWAN Stack:
24 24  )))
25 25  
26 26  * EU868 OTAA Join DR select. SF7->SF8->SF9->SF10->SF11->SF12; Each 3 attempts and then loop
27 -* US915 and AU915 OTAA Join procedure,. End node by default will use all 72 channels to join and it will be set to use the proper sub-band after Join success
27 +* US915 and AU915 OTAA Join procedure,. End node by default will use all 72 channels (All sub-bands) to join and it will be set to use the proper sub-band after Join success
28 28  
29 -
30 -
31 31  = 3. Default Frequency Bands =
32 32  
33 -
34 34  == 3.1 AS923 ==
35 35  
36 36  === 3.1.1 Notice for AS923 Frequency Bands ===
37 37  
35 +
38 38  (((
39 39  Since [[RP002-1.0.1LoRaWAN Regional Parameters>>url:https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf]], AS923 include three different default settings for different countries: AS923-1, AS923-2 and AS923-3.
40 40  )))
... ... @@ -46,6 +46,8 @@
46 46  
47 47  === 3.1.2 AS920-923 & AS923-925 : AS923-1 (AS923) ===
48 48  
47 +
48 +* **Countries**: Malaysia,
49 49  * Default Uplink channel:
50 50  ** 923.2 - SF7BW125 to SF10BW125
51 51  ** 923.4 - SF7BW125 to SF10BW125
... ... @@ -71,10 +71,9 @@
71 71  ** Uplink channels 1-8 (RX1)
72 72  ** 923.2 - SF10BW125 (RX2)
73 73  
74 -
75 -
76 76  === 3.1.3 AS923-2 ===
77 77  
76 +
78 78  * Default Uplink channel:
79 79  ** 921.4 - SF7BW125 to SF10BW125
80 80  ** 921.6 - SF7BW125 to SF10BW125
... ... @@ -85,10 +85,9 @@
85 85  ** Uplink channels 1-8 (RX1)
86 86  ** 921.4 - SF10BW125 (RX2)
87 87  
88 -
89 -
90 90  === 3.1.4 AS923-3 ===
91 91  
89 +
92 92  * Default Uplink channel:
93 93  ** 916.6 - SF7BW125 to SF10BW125
94 94  ** 916.8 - SF7BW125 to SF10BW125
... ... @@ -99,10 +99,9 @@
99 99  ** Uplink channels 1-8 (RX1)
100 100  ** 916.6 - SF10BW125 (RX2)
101 101  
102 -
103 -
104 104  === 3.1.5 AS923-4 ===
105 105  
102 +
106 106  * Countries : Israel
107 107  * Default Uplink channel:
108 108  ** 917.3 - SF7BW125 to SF10BW125
... ... @@ -115,6 +115,7 @@
115 115  
116 116  == 3.2 AU915-928(AU915) ==
117 117  
115 +
118 118  **Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]** , Default use CHE=2
119 119  
120 120  * Uplink:
... ... @@ -156,13 +156,15 @@
156 156  Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
157 157  )))
158 158  * (((
159 -Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
157 +Use the Join successful sub-band if the server doesn't include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
160 160  
159 +
161 161  
162 162  )))
163 163  
164 164  == 3.3 CN470-510 (CN470) ==
165 165  
165 +
166 166  Used in China, Default use CHE=1
167 167  
168 168  * Uplink:
... ... @@ -188,6 +188,7 @@
188 188  
189 189  == 3.4 EU863-870 (EU868) ==
190 190  
191 +
191 191  * Uplink:
192 192  ** 868.1 - SF7BW125 to SF12BW125
193 193  ** 868.3 - SF7BW125 to SF12BW125 and SF7BW250
... ... @@ -208,6 +208,7 @@
208 208  
209 209  == 3.5 IN865-867 (IN865) ==
210 210  
212 +
211 211  * Uplink:
212 212  ** 865.0625 - SF7BW125 to SF12BW125
213 213  ** 865.4025 - SF7BW125 to SF12BW125
... ... @@ -217,8 +217,20 @@
217 217  ** Uplink channels 1-3 (RX1)
218 218  ** 866.550 - SF10BW125 (RX2)
219 219  
222 +Gateway has below eight channels in IN865 bands.
223 +
224 +* 865.0625 - SF7BW125 to SF12BW125
225 +* 865.4025 - SF7BW125 to SF12BW125
226 +* 865.6025 - SF7BW125 to SF12BW125
227 +* 865.9850 - SF7BW125 to SF12BW125
228 +* 866.1850 - SF7BW125 to SF12BW125
229 +* 866.3850 - SF7BW125 to SF12BW125
230 +* 866.5850 - SF7BW125 to SF12BW125
231 +* 866.7850 - SF7BW125 to SF12BW125
232 +
220 220  == 3.6 KZ865 ==
221 221  
235 +
222 222  * Uplink ~-~- 125Khz , DR0 - DR5
223 223  ** 865.1
224 224  ** 865.2
... ... @@ -232,6 +232,7 @@
232 232  
233 233  == 3.7 KR920-923 (KR920) ==
234 234  
249 +
235 235  * Default channel:
236 236  ** 922.1 - SF7BW125 to SF12BW125
237 237  ** 922.3 - SF7BW125 to SF12BW125
... ... @@ -252,6 +252,7 @@
252 252  
253 253  == 3.8 MA869 ==
254 254  
270 +
255 255   Country: Morroco
256 256  
257 257  * Uplink:
... ... @@ -271,11 +271,13 @@
271 271  
272 272  == 3.9 US902-928 (US915) ==
273 273  
290 +
274 274  Used in USA, Canada and South America.
275 275  
276 276  
277 277  === 3.9.1 Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]. ===
278 278  
296 +
279 279  Default use CHE=2, Subband 2
280 280  
281 281  * Uplink:
... ... @@ -301,18 +301,15 @@
301 301  
302 302  === 3.9.2 Latest firmware, Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]] ===
303 303  
322 +
304 304  (((
305 305  There is an issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only work for the LoRaWAN server use sub-band2 , such as TTN. To solve this, the user needs to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvenient.
306 306  )))
307 307  
308 308  (((
309 -
328 +So since **Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]**, we have improved this, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join. In this case, the end node can support LoRaWAN servers with different subbands. To make sure the end node will only transmit the proper sub-band after OTAA Joined successfully, the end node will:
310 310  )))
311 311  
312 -(((
313 -So since **Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]**, we have improved this, the end node will use frequency 1 from sub-band1, then frequency 1 from sub-band2, then frequency 1 from sub-band3, etc to process the OTAA join, In this case, In this case, the end node can support LoRaWAN servers with different subbands. To make sure the end node will only transmit the proper sub-band after OTAA Joined successfully, the end node will:
314 -)))
315 -
316 316  * (((
317 317  Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that subband
318 318  )))
... ... @@ -319,10 +319,40 @@
319 319  * (((
320 320  Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include)
321 321  
337 +
322 322  
323 323  )))
324 324  
325 325  = 4. Frequency Bands for different server =
326 326  
343 +
327 327  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
328 328  * Loriot [[https:~~/~~/docs.loriot.io/display/LNS/Regional+Frequency+Plans>>url:https://docs.loriot.io/display/LNS/Regional+Frequency+Plans]]
346 +
347 += 5. Subband Related questiones in US915, AU915, CN470 bands. =
348 +
349 +
350 +Frequency band US915, AU915 and CN470 supports totally 72 frequency in 8 sub-bands, Normally Gateway only support 8 channels ( one subband). So how does the gateway and end nodes work in such frequency?
351 +
352 +
353 +== 5.1 Set Subband in Gateway. ==
354 +
355 +
356 +* If Gateway choose (% style="color:blue" %)**Semtech UDP packet**(%%) forwarder to Connect to LoRaWAN server. User need to manually set the match Subband in the gateway web UI.
357 +
358 +* If Gateway choose (% style="color:blue" %)**Basic Station Mode**(%%) to connect to the LoRaWAN server. User can set the subband in the Server side and gateway will the correct subband from server. no need to set this in gateway. AWS-IoT, TTN, ChirpStack all supports Basic Station Connection.
359 +
360 +== 5.2 Set Subband in End Node ==
361 +
362 +
363 +* In early End Node firmware, it is pre-set to subband 2 , user need to manually set to proper subband if they don;t use subband 2.
364 +
365 +* In new end node firmware , it supports all sub-bands, and will swtich to the proper subband after OTAA join. So user can use the end node with all sub-band.
366 +
367 +Reference: [[How it affects the OTAA Join when end node is set to support all subbands>>http://wiki.dragino.com/xwiki/bin/view/Main/LoRaWAN%20Communication%20Debug/#H13.WhyittakeslongertimeforOTAAjoinedinUS9152FCN4702FAU915band3F]]?
368 +
369 +
370 +
371 +
372 +
373 +

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0