Changes for page End Device Frequency Band

Last modified by Edwin Chen on 2024/10/21 20:35
<
From version < 11.8 >
edited by Xiaoling
on 2022/06/01 11:46
To version < 13.5 >
edited by Xiaoling
on 2022/12/14 09:25
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,5 +1,5 @@
1 1  (% class="wikigeneratedid" id="HEndDeviceFrequencyBand" %)
2 - **Contents：**
2 + **Table of** **Contents：**
3 3  
4 4  {{toc/}}
5 5  
... ... @@ -8,6 +8,7 @@
8 8  
9 9  = 1. Introduction =
10 10  
11 +
11 11  This page list the default frequency band for Dragino End Devices. The frequency bands are base on TTN Frequency Bands. User can modify upgrade firmware to support different frequency band or use AT Command to change the sub band in some frequency bands.
12 12  
13 13  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
... ... @@ -17,6 +17,7 @@
17 17  
18 18  = 2. OTAA Join Behaviour =
19 19  
21 +
20 20  For 005 LoRaWAN stack: to save battery, once boot, device will make first make 200 tries for OTAA Join, the time period of two Join Requests will depends on the DR and the airtime requirement. After this 200 Join finish, device will send a join request every 20 minutes. If device reboot, it will do above loop again.
21 21  
22 22  (((
... ... @@ -30,11 +30,11 @@
30 30  
31 31  = 3. Default Frequency Bands =
32 32  
33 -
34 34  == 3.1 AS923 ==
35 35  
36 36  === 3.1.1 Notice for AS923 Frequency Bands ===
37 37  
39 +
38 38  (((
39 39  Since [[RP002-1.0.1LoRaWAN Regional Parameters>>url:https://lora-alliance.org/sites/default/files/2020-02/rp_2-1.0.1.pdf]], AS923 include three different default settings for different countries: AS923-1, AS923-2 and AS923-3.
40 40  )))
... ... @@ -46,6 +46,8 @@
46 46  
47 47  === 3.1.2 AS920-923 & AS923-925 : AS923-1 (AS923) ===
48 48  
51 +
52 +* **Countries**: Malaysia,
49 49  * Default Uplink channel:
50 50  ** 923.2 - SF7BW125 to SF10BW125
51 51  ** 923.4 - SF7BW125 to SF10BW125
... ... @@ -75,6 +75,7 @@
75 75  
76 76  === 3.1.3 AS923-2 ===
77 77  
82 +
78 78  * Default Uplink channel:
79 79  ** 921.4 - SF7BW125 to SF10BW125
80 80  ** 921.6 - SF7BW125 to SF10BW125
... ... @@ -89,6 +89,7 @@
89 89  
90 90  === 3.1.4 AS923-3 ===
91 91  
97 +
92 92  * Default Uplink channel:
93 93  ** 916.6 - SF7BW125 to SF10BW125
94 94  ** 916.8 - SF7BW125 to SF10BW125
... ... @@ -99,8 +99,11 @@
99 99  ** Uplink channels 1-8 (RX1)
100 100  ** 916.6 - SF10BW125 (RX2)
101 101  
108 +
109 +
102 102  === 3.1.5 AS923-4 ===
103 103  
112 +
104 104  * Countries : Israel
105 105  * Default Uplink channel:
106 106  ** 917.3 - SF7BW125 to SF10BW125
... ... @@ -111,8 +111,11 @@
111 111  ** Uplink channels 1-8 (RX1)
112 112  ** 917.3 - SF10BW125 (RX2)
113 113  
123 +
124 +
114 114  == 3.2 AU915-928(AU915) ==
115 115  
127 +
116 116  **Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]** , Default use CHE=2
117 117  
118 118  * Uplink:
... ... @@ -154,13 +154,15 @@
154 154  Check what sub-band the LoRaWAN server ask from the OTAA Join Accept message and switch to that sub-band
155 155  )))
156 156  * (((
157 -Use the Join successful sub-band if the server doesn’t include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
169 +Use the Join successful sub-band if the server doesn't include sub-band info in the OTAA Join Accept message ( TTN v2 doesn't include)
158 158  
171 +
159 159  
160 160  )))
161 161  
162 162  == 3.3 CN470-510 (CN470) ==
163 163  
177 +
164 164  Used in China, Default use CHE=1
165 165  
166 166  * Uplink:
... ... @@ -184,8 +184,11 @@
184 184  ** 508.1 - SF7BW125 to SF12BW125
185 185  ** 505.3 - SF12BW125 (RX2 downlink only)
186 186  
201 +
202 +
187 187  == 3.4 EU863-870 (EU868) ==
188 188  
205 +
189 189  * Uplink:
190 190  ** 868.1 - SF7BW125 to SF12BW125
191 191  ** 868.3 - SF7BW125 to SF12BW125 and SF7BW250
... ... @@ -206,6 +206,7 @@
206 206  
207 207  == 3.5 IN865-867 (IN865) ==
208 208  
226 +
209 209  * Uplink:
210 210  ** 865.0625 - SF7BW125 to SF12BW125
211 211  ** 865.4025 - SF7BW125 to SF12BW125
... ... @@ -215,8 +215,22 @@
215 215  ** Uplink channels 1-3 (RX1)
216 216  ** 866.550 - SF10BW125 (RX2)
217 217  
236 +Gateway has below eight channels in IN865 bands.
237 +
238 +* 865.0625 - SF7BW125 to SF12BW125
239 +* 865.4025 - SF7BW125 to SF12BW125
240 +* 865.6025 - SF7BW125 to SF12BW125
241 +* 865.9850 - SF7BW125 to SF12BW125
242 +* 866.1850 - SF7BW125 to SF12BW125
243 +* 866.3850 - SF7BW125 to SF12BW125
244 +* 866.5850 - SF7BW125 to SF12BW125
245 +* 866.7850 - SF7BW125 to SF12BW125
246 +
247 +
248 +
218 218  == 3.6 KZ865 ==
219 219  
251 +
220 220  * Uplink ~-~- 125Khz , DR0 - DR5
221 221  ** 865.1
222 222  ** 865.2
... ... @@ -228,8 +228,11 @@
228 228  ** The RX1 receive window uses the same channel as the preceding uplink.
229 229  ** The RX2 receive window uses a fixed frequency and data rate. The default parameters are 866.7MHz / DR0 (SF12, 125 kHz)​
230 230  
263 +
264 +
231 231  == 3.7 KR920-923 (KR920) ==
232 232  
267 +
233 233  * Default channel:
234 234  ** 922.1 - SF7BW125 to SF12BW125
235 235  ** 922.3 - SF7BW125 to SF12BW125
... ... @@ -248,8 +248,11 @@
248 248  ** Uplink channels 1-7(RX1)
249 249  ** 921.9 - SF12BW125 (RX2 downlink only; SF12BW125 might be changed to SF9BW125)
250 250  
286 +
287 +
251 251  == 3.8 MA869 ==
252 252  
290 +
253 253   Country: Morroco
254 254  
255 255  * Uplink:
... ... @@ -267,13 +267,17 @@
267 267  ** Uplink channels 1-9 (RX1)
268 268  ** 869.525 - SF12BW125 (RX2 downlink only)
269 269  
308 +
309 +
270 270  == 3.9 US902-928 (US915) ==
271 271  
312 +
272 272  Used in USA, Canada and South America.
273 273  
274 274  
275 275  === 3.9.1 Before [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]]. ===
276 276  
318 +
277 277  Default use CHE=2, Subband 2
278 278  
279 279  * Uplink:
... ... @@ -297,8 +297,11 @@
297 297  ** 927.5 - SF7BW500 to SF12BW500
298 298  ** 923.3 - SF12BW500(RX2 downlink only)
299 299  
342 +
343 +
300 300  === 3.9.2 Latest firmware, Since [[Dragino DLS-005 LoRaWAN Stack>>url:https://www.dragino.com/downloads/downloads/LoRa_End_Node/DR-LWS/changelog]] ===
301 301  
346 +
302 302  (((
303 303  There is an issue if the end node is fixed at sub-band2. The sensor won't be able to register to other sub-band and can only work for the LoRaWAN server use sub-band2 , such as TTN. To solve this, the user needs to use a USB-TTL adapter to connect to the end node to manually set the sub-band which is very inconvenient.
304 304  )))
... ... @@ -317,10 +317,14 @@
317 317  * (((
318 318  Use the Join successful sub-band if the server doesn't include subband info in the OTAA Join Accept message ( TTN v2 doesn't include)
319 319  
365 +
320 320  
321 321  )))
322 322  
323 323  = 4. Frequency Bands for different server =
324 324  
371 +
325 325  * TTN Frequency Band Settings: [[https:~~/~~/www.thethingsnetwork.org/docs/lorawan/frequency-plans.html>>url:https://www.thethingsnetwork.org/docs/lorawan/frequency-plans.html]]
326 326  * Loriot [[https:~~/~~/docs.loriot.io/display/LNS/Regional+Frequency+Plans>>url:https://docs.loriot.io/display/LNS/Regional+Frequency+Plans]]
374 +
375 +

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0