Wiki source code of End Device AT Commands and Downlink Command

Version 38.129 by Xiaoling on 2022/06/01 11:58

version	line-number	content
16.4	1	Contents：
1.3	2
1.1	3	{{toc/}}
	4
	5
22.1	6
1.3	7	= 1. Introduction =
1.1	8
1.3	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
1.1	10
1.4	11	* Common Commands: They should be available for each sensor, such as: change uplink interval, reset device.
	12	* Sensor Related Commands: Only for special sensor, such as control relay, poll RS485 device.
1.1	13
15.2	14	(((
1.4	15	This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.
1.3	16
15.2	17	)))
1.1	18
1.3	19	= 2. How to use AT Commands or Downlink command =
1.1	20
1.3	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
38.19	23	** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
	24	** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
38.21	25	** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
1.1	26
38.101	27
	28
1.3	29	= 3. Support End Node and firmware version =
1.1	30
18.2	31	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
	32	\|=(% colspan="3" style="width: 963px;" %)(((
15.2	33	Dragino STM32 base hardware Firmware / LoRaWAN stack list
	34	)))
	35	\|(% style="width:187px" %)(((
	36	Model
18.2	37	)))\|(% style="width:330px" %)(((
15.2	38	Description
18.2	39	)))\|(% style="width:445px" %)(((
15.2	40	Firmware Version <~-~-> Stack Version
	41	)))
	42	\|(% style="width:187px" %)(((
	43	[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
18.2	44	)))\|(% style="width:330px" %)(((
15.2	45	Open Source Generic LoRaWAN Sensor Node
18.2	46	)))\|(% style="width:445px" %)(((
15.2	47	(((
	48	LSN50 v1.6.0 <~-~-> DR-LWS-003;
	49	)))
	50
	51	(((
	52	(((
7.2	53	LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
	54	)))
15.2	55	)))
	56	)))
	57	\|(% style="width:187px" %)(((
	58	[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
18.2	59	)))\|(% style="width:330px" %)(((
15.2	60	LoRaWAN GPS Tracker
18.2	61	)))\|(% style="width:445px" %)(((
15.2	62	(((
	63	LGT92 v1.6.3 <~-~-> DR-LWS-003;
	64	)))
	65
	66	(((
	67	(((
1.3	68	LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
	69	)))
15.2	70	)))
	71	)))
	72	\|(% style="width:187px" %)(((
	73	[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
18.2	74	)))\|(% style="width:330px" %)(((
15.2	75	LoRaWAN BLE Indoor Tracker
18.2	76	)))\|(% style="width:445px" %)(((
15.2	77	LBT1 v1.0 <~-~-> DR-LWS-005;
	78	)))
	79	\|(% style="width:187px" %)(((
	80	[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
18.2	81	)))\|(% style="width:330px" %)(((
15.2	82	LoRaWAN RS485 Modbus Converter
18.2	83	)))\|(% style="width:445px" %)(((
15.2	84	RS485-LN v1.3 <~-~-> DR-LWS-005;
	85	)))
	86	\|(% style="width:187px" %)(((
	87	[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
18.2	88	)))\|(% style="width:330px" %)(((
15.2	89	LoRaWAN Temperature & Humidity Sensor
18.2	90	)))\|(% style="width:445px" %)(((
15.2	91	(((
	92	LHT65 v1.7 <~-~-> DR-LWS-003;
	93	)))
	94
	95	(((
	96	(((
1.3	97	LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
	98	)))
15.2	99	)))
	100	)))
1.1	101
38.102	102
38.103	103
1.3	104	= 4. System Management Commands =
1.1	105
1.3	106	== 4.1 Change Uplink Interval ==
1.1	107
1.3	108	Feature: Change LoRaWAN End Node Transmit Interval.
	109
4.2	110	(% class="box infomessage" %)
	111	(((
7.5	112	AT Command: AT+TDC
4.2	113	)))
1.3	114
12.1	115	(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
7.5	116	\|=(% colspan="3" style="width: 724px;" %)AT+TDC
5.4	117	\|(% style="width:165px" %)Command Example\|(% style="width:227px" %)Function\|(% style="width:329px" %)Response
	118	\|(% style="width:165px" %)AT+TDC=?\|(% style="width:227px" %)Show current transmit Interval\|(% style="width:329px" %)30000(((
1.3	119	OK
	120
	121	the interval is 30000ms = 30s
	122	)))
5.4	123	\|(% style="width:165px" %)AT+TDC=60000\|(% style="width:227px" %)Set Transmit Interval\|(% style="width:329px" %)OK(((
1.3	124	Set transmit interval to 60000ms = 60 seconds
	125	)))
	126
7.5	127	{{info}}
4.2	128	Downlink Command: 0x01
7.5	129	{{/info}}
1.3	130
15.6	131	(((
1.3	132	Format: Command Code (0x01) followed by 3 bytes time value.
15.6	133	)))
1.3	134
15.3	135	(((
1.3	136	If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
15.3	137	)))
1.3	138
4.2	139	* Example 1: Downlink Payload: 0100001E ~/~/ Set Transmit Interval (TDC) = 30 seconds
	140	* Example 2: Downlink Payload: 0100003C ~/~/ Set Transmit Interval (TDC) = 60 seconds
1.3	141
38.104	142
	143
1.3	144	== 4.2 Reboot End Node ==
	145
	146	Feature: Reboot End Node to perform a new OTAA or ABP Join.
	147
4.2	148	{{info}}
7.5	149	AT Command: ATZ
4.2	150	{{/info}}
1.3	151
15.1	152	(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
7.5	153	\|=(% colspan="3" %)ATZ: Trig a reset of the MCU
1.3	154	\|Command Example\|Function\|Response
7.2	155	\|ATZ\|Reset MCU\|(((
4.3	156	Device reset and show booting info
1.3	157
4.3	158	LSN50 Device/LoRa ST Module
	159
1.3	160	Image Version: XX
4.3	161
1.3	162	Frequency Band: XX
4.3	163
1.3	164	DevEui= XX XX XX XX XX XX XX XX
	165
	166	<followed by the Tx and Rx information>
4.3	167	)))
1.3	168
7.5	169	{{info}}
	170	Downlink Command: 0x04
	171	{{/info}}
1.3	172
15.7	173	(((
1.3	174	Format: Command Code (0x04) followed by FF.
15.7	175	)))
1.3	176
15.7	177	(((
7.5	178	If the downlink payload=04FF, the end node will reboot.
20.1	179
	180
15.7	181	)))
1.3	182
	183	== 4.3 Reset to factory Default ==
	184
	185	Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
	186
7.5	187	{{info}}
	188	AT Command: AT+FDR
	189	{{/info}}
1.3	190
15.1	191	(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
7.5	192	\|=(% colspan="3" style="width: 828px;" %)Reset to factory default
	193	\|(% style="width:181px" %)Command Example\|(% style="width:181px" %)Function\|(% style="width:465px" %)Response
	194	\|(% style="width:181px" %)AT+FDR\|(% style="width:181px" %)Reset to factory default\|(% style="width:465px" %)(((
	195	Device reset to factory default parameters and show booting info
1.3	196
7.5	197	LSN50 Device/LoRa ST Module
	198
1.3	199	Image Version: XX
7.5	200
1.3	201	Frequency Band: XX
7.5	202
1.3	203	DevEui= XX XX XX XX XX XX XX XX
7.5	204
1.3	205	Please set the parameters or reset Device to apply change
7.5	206	)))
1.3	207
7.5	208	{{info}}
	209	Downlink Command: 0x04
	210	{{/info}}
1.3	211
15.7	212	(((
1.3	213	Format: Command Code (0x04) followed by FE.
15.7	214	)))
1.3	215
15.7	216	(((
7.5	217	If the downlink payload=04FE, Reset Parameters to Factory Default, Keys Reserve.
15.7	218	)))
1.3	219
	220
	221	== 4.4 Show Firmware Version ==
	222
	223	Feature: Show firmware version. No downlink command yet.
	224
7.5	225	{{info}}
	226	AT Command: AT+VER
	227	{{/info}}
1.3	228
18.2	229	(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
	230	\|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
	231	\|(% style="width:170px" %)Command Example\|(% style="width:300px" %)Function\|(% style="width:113px" %)Response
	232	\|(% style="width:170px" %)AT+VER=?\|(% style="width:300px" %)Show Image version and Frequency Band\|(% style="width:113px" %)(((
7.5	233	1.3 EU868
1.3	234
	235	OK
7.5	236	)))
1.3	237
7.5	238	{{info}}
	239	Downlink Command: 0x26 (Valid in 006 stack)
	240	{{/info}}
1.3	241
15.7	242	(((
1.3	243	Downlink Format: 0x26
15.7	244	)))
1.3	245
15.3	246	(((
1.3	247	Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
15.3	248	)))
1.3	249
15.7	250	(((
7.5	251	xx: Software Type:
15.7	252	)))
1.3	253
	254	* 0x00 01: LGT92 Version
	255	* 0x00 02: LBT1
	256	* 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
	257
15.7	258	(((
7.5	259	yy: Frequency Band:
15.7	260	)))
1.3	261
	262	* 0x01: EU868
	263	* 0x02: US915
	264	* 0x03: IN865
	265	* 0x04: AU915
	266	* 0x05: KZ865
	267	* 0x06: RU864
	268	* 0x07: AS923
	269	* 0x08: AS923-1
	270	* 0x09: AS923-2
	271	* 0xa0: AS923-3
	272
15.7	273	(((
7.5	274	zz: Subband
15.7	275	)))
1.3	276
	277	firmware version: v1.1.0 ~-~-> 110
	278
	279
	280	== 4.5 Show System Configure ==
	281
	282	Feature: Show All configure. No downlink command yet.
	283
7.5	284	{{info}}
	285	AT Command: AT+CFG
	286	{{/info}}
1.3	287
15.1	288	(% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
7.5	289	\|=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
	290	\|(% style="width:160px" %)Command Example\|(% style="width:154px" %)Function\|(% style="width:280px" %)Response
	291	\|(% style="width:160px" %)AT+CFG\|(% style="width:154px" %)Show all configures\|(% style="width:280px" %)(((
	292	AT+DEUI = XX XX XX XX XX XX XX XX
1.3	293
	294	AT+DADDR=XXXXXXXX
7.5	295
1.3	296	……….
7.5	297
1.3	298	AT+RX2WTO=X
7.5	299
1.3	300	AT+CHS=868100000
7.5	301
1.3	302	OK
7.5	303	)))
1.3	304
38.105	305
	306
1.3	307	= 5. Keys, IDs and EUIs management =
	308
	309	== 5.1 Application EUI ==
	310
	311	Feature: Get or Set the Application EUI.
	312
7.5	313	{{info}}
	314	AT Command: AT+APPEUI
	315	{{/info}}
1.3	316
15.1	317	(% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
7.5	318	\|=(% colspan="3" style="width: 683px;" %)AT+APPEUI
	319	\|(% style="width:305px" %)Command Example\|(% style="width:186px" %)Function\|(% style="width:191px" %)Response
	320	\|(% style="width:305px" %)AT+APPEUI=?\|(% style="width:186px" %)Get the Application EUI\|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
1.3	321	OK
	322	)))
7.5	323	\|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34\|(% style="width:186px" %)Set the Application EUI\|(% style="width:191px" %)OK
1.3	324
38.106	325
	326
1.3	327	== 5.2 Application Key ==
	328
	329	Feature: Get or Set the Application Key.
	330
7.5	331	{{info}}
	332	AT Command: AT+APPKEY
	333	{{/info}}
1.3	334
15.1	335	(% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
7.5	336	\|=(% colspan="3" style="width: 973px;" %)AT+APPKEY
	337	\|(% style="width:441px" %)Command Example\|(% style="width:180px" %)Function\|(% style="width:350px" %)Response
	338	\|(% style="width:441px" %)AT+APPKEY=?\|(% style="width:180px" %)Get the Application Key\|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
1.3	339	OK
	340	)))
7.5	341	\|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35\|(% style="width:180px" %)Set the Application Key\|(% style="width:350px" %)OK
1.3	342
38.107	343
	344
1.3	345	== 5.3 Application Session Key ==
	346
	347	Feature: Get or Set the Application Session Key.
	348
7.6	349	{{info}}
	350	AT Command: AT+APPSKEY
	351	{{/info}}
1.3	352
15.1	353	(% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
7.6	354	\|=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
	355	\|(% style="width:451px" %)Command Example\|(% style="width:231px" %)Function\|(% style="width:354px" %)Response
	356	\|(% style="width:451px" %)AT+APPSKEY=?\|(% style="width:231px" %)Get the Application Session Key\|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
1.3	357	OK
	358	)))
7.6	359	\|(% style="width:451px" %)AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2\|(% style="width:231px" %)Set the Application Session Key\|(% style="width:354px" %)(While Error in format, return AT_PARAM_ERROR)(((
1.3	360	OK
	361	)))
	362
38.108	363
	364
1.3	365	== 5.4 Device Address ==
	366
	367	Feature: Get or Set the Device Address.
	368
7.6	369	{{info}}
	370	AT Command: AT+DADDR
	371	{{/info}}
1.3	372
15.1	373	(% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
7.6	374	\|=(% colspan="3" style="width: 792px;" %)AT+DADDR
	375	\|(% style="width:192px" %)Command Example\|(% style="width:241px" %)Function\|(% style="width:359px" %)Response
	376	\|(% style="width:192px" %)AT+DADDR=?\|(% style="width:241px" %)Get the Application Session Key.\|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
1.3	377	A8 40 41 FF
	378
	379	OK
	380	)))
7.6	381	\|(% style="width:192px" %)AT+DADDR=A8 40 41 FF\|(% style="width:241px" %)Set the Application Session Key.\|(% style="width:359px" %)OK
1.3	382
38.109	383
	384
1.3	385	== 5.5 Device EUI ==
	386
	387	Feature: Get or Set the Device EUI.
	388
7.6	389	{{info}}
	390	AT Command: AT+DEUI
	391	{{/info}}
1.3	392
15.1	393	(% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
7.6	394	\|=(% colspan="3" style="width: 1032px;" %)AT+DEUI
	395	\|(% style="width:250px" %)Command Example\|(% style="width:147px" %)Function\|(% style="width:634px" %)Response
	396	\|(% style="width:250px" %)AT+DEUI=?\|(% style="width:147px" %)Get the Device EUI.\|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
1.3	397	OK
	398	)))
7.6	399	\|(% style="width:250px" %)AT+DEUI=A8 40 41 FF FF 12 34 56\|(% style="width:147px" %)Set the Device EUI.\|(% style="width:634px" %)(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
1.3	400	OK
	401	)))
	402
38.110	403
	404
1.3	405	== 5.6 Network ID ==
	406
	407	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
	408
7.6	409	{{info}}
	410	AT Command: AT+NWKID
	411	{{/info}}
1.3	412
15.1	413	(% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
7.6	414	\|=(% colspan="3" style="width: 445px;" %)AT+NWKID
	415	\|(% style="width:191px" %)Command Example\|(% style="width:153px" %)Function\|(% style="width:101px" %)Response
	416	\|(% style="width:191px" %)AT+NWKID=?\|(% style="width:153px" %)Get the Network ID.\|(% style="width:101px" %)a8 40 41 ff(((
1.3	417	OK
	418	)))
7.6	419	\|(% style="width:191px" %)AT+NWKID=A8 40 41 FF\|(% style="width:153px" %)Set the Network ID.\|(% style="width:101px" %)OK
1.3	420
38.111	421
	422
1.3	423	== 5.7 Network Session Key ==
	424
	425	Feature: Get or Set the Network Session Key
	426
7.6	427	{{info}}
	428	AT Command: AT+NWKSKEY
	429	{{/info}}
1.3	430
15.1	431	(% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
7.6	432	\|=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
	433	\|(% style="width:455px" %)Command Example\|(% style="width:215px" %)Function\|(% style="width:343px" %)Response
	434	\|(% style="width:455px" %)AT+NWKSKEY=?\|(% style="width:215px" %)Get the Network Session Key.\|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
1.3	435	OK
	436	)))
7.6	437	\|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07\|(% style="width:215px" %)Set the Network Session Key.\|(% style="width:343px" %)OK
1.3	438
38.113	439
	440
1.3	441	= 6. Joining and sending date on LoRaWAN network =
	442
	443	== 6.1 Confirm Mode ==
	444
	445	Feature: Get or Set the confirmation mode (0-1).
	446
7.6	447	{{info}}
	448	AT Command: AT+CFM
	449	{{/info}}
1.3	450
15.1	451	(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
7.6	452	\|=(% colspan="3" style="width: 707px;" %)AT+CFM
	453	\|(% style="width:155px" %)Command Example\|(% style="width:205px" %)Function\|(% style="width:346px" %)Response
	454	\|(% style="width:155px" %)AT+CFM=?\|(% style="width:205px" %)Get the confirmation mode\|(% style="width:346px" %)0(((
1.3	455	OK
	456	)))
7.6	457	\|(% style="width:155px" %)AT+CFM=1\|(% style="width:205px" %)Set the confirmation mode\|(% style="width:346px" %)OK
	458	\|(% style="width:155px" %)AT+CFM=2\|(% style="width:205px" %)Set the confirmation mode\|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
1.3	459
	460	Downlink Command: 0x05
	461
	462	Format: Command Code (0x05) followed by 2 bytes mode value.
	463
	464	If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
	465
	466	* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
	467	* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
	468
38.113	469
	470
1.3	471	== 6.2 Confirm Status ==
	472
	473	Feature: Get confirmation status of the last AT+SEND (0-1).
	474
7.7	475	{{info}}
	476	AT Command: AT+CFS
	477	{{/info}}
1.3	478
15.1	479	(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
7.7	480	\|=(% colspan="3" style="width: 531px;" %)AT+CFS
	481	\|(% style="width:156px" %)Command Example\|(% style="width:193px" %)Function\|(% style="width:178px" %)Response
	482	\|(% style="width:156px" %)AT+CFS=?\|(% style="width:193px" %)Get confirmation status\|(% style="width:178px" %)0(((
1.3	483	OK
	484	)))
	485
38.114	486
	487
1.3	488	== 6.3 Join LoRa® Network ==
	489
	490	Feature: Join network.
	491
7.7	492	{{info}}
	493	AT Command: AT+JOIN
	494	{{/info}}
1.3	495
15.1	496	(% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
7.7	497	\|=(% colspan="3" style="width: 644px;" %)AT+JOIN
	498	\|(% style="width:163px" %)Command Example\|(% style="width:147px" %)Function\|(% style="width:334px" %)Response
	499	\|(% style="width:163px" %)AT+JOIN ?\|(% style="width:147px" %)Get imformation.\|(% style="width:334px" %)AT+JOIN: Join network(((
1.3	500	OK
	501
	502	While Error in format, return AT_BUSY_ERROR
	503	)))
	504
38.115	505
	506
1.3	507	== 6.4 LoRa® Network Join Mode ==
	508
	509	Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
	510
7.7	511	{{info}}
	512	AT Command: AT+NJM
	513	{{/info}}
1.3	514
15.1	515	(% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
7.7	516	\|=(% colspan="3" style="width: 750px;" %)AT+NJM
	517	\|(% style="width:162px" %)Command Example\|(% style="width:227px" %)Function\|(% style="width:361px" %)Response
	518	\|(% style="width:162px" %)AT+NJM=?\|(% style="width:227px" %)Get the Network Join Mode\|(% style="width:361px" %)1(((
1.3	519	OK
	520	)))
7.7	521	\|(% style="width:162px" %)AT+NJM=0\|(% style="width:227px" %)Set the Network Join Mode\|(% style="width:361px" %)OK
	522	\|(% style="width:162px" %)AT+NJM=2\|(% style="width:227px" %)Set the Network Join Mode\|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
1.3	523
7.8	524	{{info}}
	525	Downlink Command: 0x20
	526	{{/info}}
1.3	527
	528	Format: Command Code (0x20) followed by 1 bytes mode value.
	529
	530	If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
	531
7.8	532	* Example 1: Downlink Payload: 2000 ~/~/ Set AT+NJM=O
	533	* Example 2: Downlink Payload: 2001 ~/~/ Set AT+NJM=1
1.3	534
38.116	535
	536
1.3	537	== 6.5 LoRa® Network Join Status ==
	538
	539	Feature: LoRa® Network Join Status.
	540
7.8	541	{{info}}
	542	AT Command: AT+NJS
	543	{{/info}}
1.3	544
15.1	545	(% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
7.8	546	\|=(% colspan="3" style="width: 495px;" %)AT+NJS
	547	\|(% style="width:169px" %)Command Example\|(% style="width:164px" %)Function\|(% style="width:161px" %)Response
	548	\|(% style="width:169px" %)AT+NJS=?\|(% style="width:164px" %)Get the join status.\|(% style="width:161px" %)0(((
1.3	549	OK
	550	)))
	551
38.117	552
	553
1.3	554	== 6.6 Print Last Received Data in Raw Format ==
	555
	556	Feature: Print Last Received Data in Raw Format<port:data>.
	557
7.8	558	{{info}}
	559	AT Command: AT+RECV
	560	{{/info}}
1.3	561
15.1	562	(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
7.8	563	\|=(% colspan="3" style="width: 584px;" %)AT+RECV
	564	\|(% style="width:161px" %)Command Example\|(% style="width:272px" %)Function\|(% style="width:150px" %)Response
	565	\|(% style="width:161px" %)AT+RECV=?\|(% style="width:272px" %)print last received data in raw format.\|(% style="width:150px" %)0:(((
1.3	566	OK
	567	)))
	568
38.118	569
	570
1.3	571	== 6.7 Print Last Received Data in Binary Format ==
	572
	573	Feature: Print Last Received Data in Binary Format<port:data>.
	574
7.8	575	{{info}}
	576	AT Command: AT+RECVB
	577	{{/info}}
1.3	578
15.1	579	(% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
7.8	580	\|=(% colspan="3" style="width: 790px;" %)AT+RECVB
	581	\|(% style="width:173px" %)Command Example\|(% style="width:497px" %)Function\|(% style="width:120px" %)Response
	582	\|(% style="width:173px" %)AT+RECVB=?\|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).\|(% style="width:120px" %)2: 0010(((
1.3	583	OK
	584	)))
	585
38.119	586
	587
1.3	588	== 6.8 Send Text Data ==
	589
	590	Feature: Send Text Data<port:data>.
	591
7.8	592	{{info}}
	593	AT Command: AT+SEND
	594	{{/info}}
1.3	595
15.1	596	(% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
7.8	597	\|=(% colspan="3" style="width: 988px;" %)AT+SEND
	598	\|(% style="width:201px" %)Command Example\|(% style="width:340px" %)Function\|(% style="width:446px" %)Response
	599	\|(% style="width:201px" %)AT+SEND=12:hello world\|(% style="width:340px" %)Send text data along with the application port.\|(% style="width:446px" %)OK(((
1.3	600	While Error in format, return
	601
	602	AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
	603
	604
	605	)))
	606
38.120	607
	608
1.3	609	== 6.9 Send Hexadecimal Data ==
	610
	611	Feature: Send hexadecimal data along with the application port.
	612
7.8	613	{{info}}
	614	AT Command: AT+SENDB
	615	{{/info}}
1.3	616
15.1	617	(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
7.8	618	\|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
	619	\|(% style="width:257px" %)Command Example\|(% style="width:406px" %)Function\|(% style="width:453px" %)Response
	620	\|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789\|(% style="width:406px" %)Send hexadecimal data along with the application port.\|(% style="width:453px" %)OK
	621	\|(% style="width:257px" %)AT+SENDB=abcdef0123456789\|(% style="width:406px" %)Send hexadecimal data along with the application port.\|(% style="width:453px" %)While Error in format, return(((
1.3	622	AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
	623
	624
	625	)))
	626
38.121	627
	628
1.3	629	= 7. LoRaWAN network management =
	630
	631	== 7.1 Adaptive Data Rate ==
	632
	633	Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
	634
7.8	635	{{info}}
	636	AT Command: AT+ADR
	637	{{/info}}
1.3	638
15.1	639	(% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
7.8	640	\|=(% colspan="3" style="width: 680px;" %)AT+ADR
	641	\|(% style="width:162px" %)Command Example\|(% style="width:266px" %)Function\|(% style="width:250px" %)Response
	642	\|(% style="width:162px" %)AT+ADR=?\|(% style="width:266px" %)Get the Adaptive Data Rate setting.\|(% style="width:250px" %)1(((
1.3	643	OK
	644	)))
7.8	645	\|(% style="width:162px" %)AT+ADR=0\|(% style="width:266px" %)Set the Adaptive Data Rate setting.\|(% style="width:250px" %)OK
	646	\|(% style="width:162px" %)AT+ADR=2\|(% style="width:266px" %)Set the Adaptive Data Rate setting.\|(% style="width:250px" %)While Error in format, return(((
1.3	647	AT_PARAM_ERROR
	648	)))
	649
7.8	650	{{info}}
	651	Downlink Command: 0x22
	652	{{/info}}
1.3	653
	654
	655	If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
	656
7.8	657	* Example 1: Downlink Payload: 2201 ~/~/ Set AT+ADR=1.
	658	* Example 2: Downlink Payload: 2200FFFF ~/~/ Set AT+ADR=0.
1.3	659
38.122	660
	661
1.3	662	== 7.2 LoRa® Class ==
	663
	664	Feature: Get or Set the Device Class(Currently only support class A, class C).
	665
7.8	666	{{info}}
	667	AT Command:AT+CLASS
	668	{{/info}}
1.3	669
15.1	670	(% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
7.8	671	\|=(% colspan="3" style="width: 504px;" %)AT+CLASS
	672	\|(% style="width:163px" %)Command Example\|(% style="width:166px" %)Function\|(% style="width:175px" %)Response
	673	\|(% style="width:163px" %)AT+CLASS=?\|(% style="width:166px" %)Get the Device Class.\|(% style="width:175px" %)A(((
1.3	674	OK
	675	)))
7.8	676	\|(% style="width:163px" %)AT+CLASS=C\|(% style="width:166px" %)Set the Device Class.\|(% style="width:175px" %)OK(((
1.3	677
	678	)))
	679
38.123	680
	681
1.3	682	== 7.3 Duty Cycle Setting ==
	683
	684	Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
	685
7.8	686	{{info}}
	687	AT Command:AT+DCS
	688	{{/info}}
1.3	689
15.1	690	(% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
7.8	691	\|=(% colspan="3" style="width: 512px;" %)AT+DCS
	692	\|(% style="width:165px" %)Command Example\|(% style="width:239px" %)Function\|(% style="width:107px" %)Response
	693	\|(% style="width:165px" %)AT+DCS=?\|(% style="width:239px" %)Get the ETSI Duty Cycle setting.\|(% style="width:107px" %)1(((
1.3	694	OK
	695	)))
7.8	696	\|(% style="width:165px" %)AT+DCS=1\|(% style="width:239px" %)Set the ETSI Duty Cycle setting.\|(% style="width:107px" %)OK(((
1.3	697
	698	)))
	699
38.124	700
	701
1.3	702	== 7.4 Data Rate ==
	703
	704	Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
	705
7.8	706	{{info}}
	707	AT Command: AT+DR
	708	{{/info}}
1.3	709
15.1	710	(% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
7.8	711	\|=(% colspan="3" style="width: 463px;" %)AT+DR
	712	\|(% style="width:156px" %)Command Example\|(% style="width:167px" %)Function\|(% style="width:140px" %)Response
	713	\|(% style="width:156px" %)AT+DR=?\|(% style="width:167px" %)Get the Data Rate.\|(% style="width:140px" %)5(((
1.3	714	OK
	715	)))
7.8	716	\|(% style="width:156px" %)AT+DR=2\|(% style="width:167px" %)Set the Data Rate.\|(% style="width:140px" %)OK(((
1.3	717
	718	)))
	719
7.8	720	{{info}}
	721	Downlink Command: 0x2200aaFF
	722	{{/info}}
1.3	723
	724
	725	If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
	726
7.8	727	* Example 1: Downlink Payload: 220001FF ~/~/ Set AT+DR=1.
	728	* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+DR=0.
1.3	729
38.125	730
	731
1.3	732	== 7.5 Frame Counter Downlink ==
	733
	734	Feature: Get or Set the Frame Counter Downlink.
	735
7.8	736	{{info}}
	737	AT Command:AT+FCD
	738	{{/info}}
1.3	739
15.1	740	(% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
7.8	741	\|=(% colspan="3" style="width: 690px;" %)AT+FCD
	742	\|(% style="width:162px" %)Command Example\|(% style="width:258px" %)Function\|(% style="width:269px" %)Response
	743	\|(% style="width:162px" %)AT+FCD=?\|(% style="width:258px" %)Get the Frame Counter Downlink.\|(% style="width:269px" %)0(((
1.3	744	OK
	745	)))
7.8	746	\|(% style="width:162px" %)AT+FCD=10\|(% style="width:258px" %)Set the Frame Counter Downlink.\|(% style="width:269px" %)(System will write new value to FCD)(((
1.3	747	OK
	748
	749
	750	)))
	751
38.126	752
	753
1.3	754	== 7.6 Frame Counter Uplink ==
	755
	756	Feature: Get or Set the Frame Counter Uplink.
	757
7.8	758	{{info}}
	759	AT Command:AT+FCU
	760	{{/info}}
1.3	761
15.1	762	(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
7.8	763	\|=(% colspan="3" style="width: 531px;" %)AT+FCU
	764	\|(% style="width:177px" %)Command Example\|(% style="width:239px" %)Function\|(% style="width:113px" %)Response
	765	\|(% style="width:177px" %)AT+FCU=?\|(% style="width:239px" %)Get the Frame Counter Uplink.\|(% style="width:113px" %)0(((
1.3	766	OK
	767	)))
7.8	768	\|(% style="width:177px" %)AT+FCU=10\|(% style="width:239px" %)Set the Frame Counter Uplink.\|(% style="width:113px" %)OK(((
1.3	769
	770	)))
	771
38.127	772
	773
1.3	774	== 7.7 Join Accept Delay1 ==
	775
	776	Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
	777
7.8	778	{{info}}
	779	AT Command:AT+JN1DL
	780	{{/info}}
1.3	781
15.1	782	(% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
7.8	783	\|=(% colspan="3" style="width: 534px;" %)AT+JN1DL
	784	\|(% style="width:164px" %)Command Example\|(% style="width:229px" %)Function\|(% style="width:140px" %)Response
	785	\|(% style="width:164px" %)AT+JN1DL=?\|(% style="width:229px" %)Get the Join Accept Delay.\|(% style="width:140px" %)5000(((
1.3	786	OK
	787	)))
7.8	788	\|(% style="width:164px" %)AT+JN1DL=10000\|(% style="width:229px" %)Set the Join Accept Delay.\|(% style="width:140px" %)OK(((
1.3	789
	790	)))
	791
38.128	792
	793
1.3	794	== 7.8 Join Accept Delay2 ==
	795
	796	Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
	797
7.8	798	{{info}}
	799	AT Command:AT+JN2DL
	800	{{/info}}
1.3	801
15.1	802	(% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
7.8	803	\|=(% colspan="3" style="width: 535px;" %)AT+JN2DL
	804	\|(% style="width:160px" %)Command Example\|(% style="width:228px" %)Function\|(% style="width:146px" %)Response
	805	\|(% style="width:160px" %)AT+JN2DL=?\|(% style="width:228px" %)Get the Join Accept Delay.\|(% style="width:146px" %)6000(((
1.3	806	OK
	807	)))
7.8	808	\|(% style="width:160px" %)AT+JN2DL=20000\|(% style="width:228px" %)Set the Join Accept Delay.\|(% style="width:146px" %)OK(((
1.3	809
	810	)))
	811
38.129	812
	813
1.3	814	== 7.9 Public Network Mode ==
	815
	816	Feature: Get or Set the public network mode. (0: off, 1: on)
	817
7.8	818	{{info}}
	819	AT Command:AT+PNM
	820	{{/info}}
1.3	821
15.1	822	(% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
7.8	823	\|=(% colspan="3" style="width: 664px;" %)AT+PNM
	824	\|(% style="width:166px" %)Command Example\|(% style="width:225px" %)Function\|(% style="width:272px" %)Response
	825	\|(% style="width:166px" %)AT+PNM=?\|(% style="width:225px" %)Get the public network mode.\|(% style="width:272px" %)1(((
1.3	826	OK
	827	)))
7.8	828	\|(% style="width:166px" %)AT+PNM=1\|(% style="width:225px" %)Set the public network mode.\|(% style="width:272px" %)(System will write new value to PNM)(((
1.3	829	OK
	830
	831
	832	)))
	833
	834	== 7.10 Receive Delay1 ==
	835
	836	Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
	837
7.8	838	{{info}}
	839	AT Command:AT+RX1DL
	840	{{/info}}
1.3	841
15.1	842	(% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
7.8	843	\|=(% colspan="3" style="width: 405px;" %)AT+RX1DL
	844	\|(% style="width:155px" %)Command Example\|(% style="width:128px" %)Function\|(% style="width:122px" %)Response
	845	\|(% style="width:155px" %)AT+RX1DL=?\|(% style="width:128px" %)Get the delay.\|(% style="width:122px" %)1000(((
1.3	846	OK
	847	)))
7.8	848	\|(% style="width:155px" %)AT+RX1DL=1500\|(% style="width:128px" %)Set the delay.\|(% style="width:122px" %)OK(((
1.3	849
	850	)))
	851
21.1	852	== 7.11 Receive Delay2 ==
	853
1.3	854	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
	855
7.9	856	{{info}}
	857	AT Command:AT+RX2DL
	858	{{/info}}
1.3	859
15.1	860	(% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
7.9	861	\|=(% colspan="3" style="width: 478px;" %)AT+RX2DL
	862	\|(% style="width:175px" %)Command Example\|(% style="width:152px" %)Function\|(% style="width:150px" %)Response
	863	\|(% style="width:175px" %)AT+RX2DL=?\|(% style="width:152px" %)Get the delay.\|(% style="width:150px" %)2000(((
1.3	864	OK
	865	)))
7.9	866	\|(% style="width:175px" %)AT+RX2DL=2500\|(% style="width:152px" %)Set the delay.\|(% style="width:150px" %)OK(((
1.3	867
	868	)))
	869
	870	== 7.12 Rx2 Window Data Rate ==
	871
	872	Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
	873
7.9	874	{{info}}
	875	AT Command:AT+RX2DR
	876	{{/info}}
1.3	877
15.1	878	(% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
7.9	879	\|=(% colspan="3" style="width: 522px;" %)AT+RX2DR
	880	\|(% style="width:160px" %)Command Example\|(% style="width:232px" %)Function\|(% style="width:130px" %)Response
	881	\|(% style="width:160px" %)AT+RX2DR=?\|(% style="width:232px" %)Get the Rx2 window data rate.\|(% style="width:130px" %)2(((
1.3	882	OK
	883	)))
7.9	884	\|(% style="width:160px" %)AT+RX2DR=6\|(% style="width:232px" %)Set the Rx2 window data rate.\|(% style="width:130px" %)OK(((
1.3	885
	886	)))
	887
	888	== 7.13 Rx2 Window Frequency ==
	889
	890	Feature: Get or Set the Rx2 window frequency
	891
7.9	892	{{info}}
	893	AT Command:AT+RX2FQ
	894	{{/info}}
1.3	895
15.1	896	(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
7.9	897	\|=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
	898	\|(% style="width:183px" %)Command Example\|(% style="width:240px" %)Function\|(% style="width:160px" %)Response
	899	\|(% style="width:183px" %)AT+RX2FQ=?\|(% style="width:240px" %)Get the Rx2 window frequency.\|(% style="width:160px" %)434665000(((
1.3	900	OK
	901	)))
7.9	902	\|(% style="width:183px" %)AT+RX2FQ=434665000\|(% style="width:240px" %)Set the Rx2 window frequency.\|(% style="width:160px" %)OK(((
1.3	903
	904	)))
	905
	906	== 7.14 Transmit Power ==
	907
	908	Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
	909
7.9	910	{{info}}
	911	AT Command:AT+TXP
	912	{{/info}}
1.3	913
15.1	914	(% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
7.9	915	\|=(% colspan="3" style="width: 462px;" %)AT+TXP
	916	\|(% style="width:161px" %)Command Example\|(% style="width:189px" %)Function\|(% style="width:112px" %)Response
	917	\|(% style="width:161px" %)AT+TXP=?\|(% style="width:189px" %)Get the Transmit Power.\|(% style="width:112px" %)0(((
1.3	918	OK
	919	)))
7.9	920	\|(% style="width:161px" %)AT+TXP=1\|(% style="width:189px" %)Set the Transmit Power.\|(% style="width:112px" %)OK(((
1.3	921
	922	)))
	923
	924	Downlink Payload. The 4th byte of 0x22 downlink.
	925
	926	If the downlink payload=22000100, it means setting the TXP to 0.
	927
7.9	928	* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2.
	929	* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0.
1.3	930
	931	== 7.15 RSSI of the Last Received Packet ==
	932
	933	Feature: Get or Set the Rx2 window frequency
	934
7.9	935	{{info}}
	936	AT Command:AT+RSSI
	937	{{/info}}
1.3	938
15.1	939	(% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
7.9	940	\|=(% colspan="3" style="width: 554px;" %)AT+RSSI
	941	\|(% style="width:164px" %)Command Example\|(% style="width:289px" %)Function\|(% style="width:100px" %)Response
	942	\|(% style="width:164px" %)AT+RSSI=?\|(% style="width:289px" %)Get the RSSI of the last received packet.\|(% style="width:100px" %)0(((
1.3	943	OK
	944	)))
	945
	946	== 7.16 SNR of the Last Received Packet ==
	947
	948	Feature: Get the SNR of the last received packet
	949
7.9	950	{{info}}
	951	AT Command:AT+SNR
	952	{{/info}}
1.3	953
15.1	954	(% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
7.9	955	\|=(% colspan="3" style="width: 568px;" %)AT+SNR
	956	\|(% style="width:164px" %)Command Example\|(% style="width:290px" %)Function\|(% style="width:113px" %)Response
	957	\|(% style="width:164px" %)AT+SNR=?\|(% style="width:290px" %)Get the RSSI of the last received packet.\|(% style="width:113px" %)0(((
1.3	958	OK
	959	)))
	960
	961	== 7.17 Application Port ==
	962
	963	Feature: Get or set the application port.
	964
7.9	965	{{info}}
	966	AT Command: AT+PORT
	967	{{/info}}
1.3	968
15.1	969	(% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
7.9	970	\|=(% colspan="3" style="width: 497px;" %)AT+PORT
	971	\|(% style="width:157px" %)Command Example\|(% style="width:204px" %)Function\|(% style="width:135px" %)Response
	972	\|(% style="width:157px" %)AT+PORT=?\|(% style="width:204px" %)Get the application port\|(% style="width:135px" %)21(((
1.3	973	OK
	974	)))
7.9	975	\|(% style="width:157px" %)AT+PORT=21\|(% style="width:204px" %)Set the application port\|(% style="width:135px" %)OK
1.3	976
7.9	977	{{info}}
	978	Downlink Command: 0x23
	979	{{/info}}
1.3	980
	981	Format: Command Code (0x23) followed by 1 bytes port value.
	982
	983	If the downlink payload=2301, it means set the application port to 1, while type code is 23.
	984
7.9	985	* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1
	986	* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5
1.3	987
	988	== 7.18 Single Channel Mode ==
	989
	990	Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
	991
7.9	992	{{info}}
	993	AT Command: AT+CHS
	994	{{/info}}
1.3	995
15.1	996	(% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
7.9	997	\|=(% colspan="3" style="width: 600px;" %)AT+CHS
	998	\|(% style="width:182px" %)Command Example\|(% style="width:295px" %)Function\|(% style="width:122px" %)Response
	999	\|(% style="width:182px" %)AT+CHS=?\|(% style="width:295px" %)Get Frequency for Single Channel Mode\|(% style="width:122px" %)0(((
1.3	1000	OK
	1001	)))
7.9	1002	\|(% style="width:182px" %)AT+CHS=868100000\|(% style="width:295px" %)Set Frequency for Single Channel Mode\|(% style="width:122px" %)OK
1.3	1003
	1004	== 7.19 Eight Channel Mode ==
	1005
	1006	Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
	1007
7.9	1008	{{info}}
	1009	AT Command: AT+CHE
	1010	{{/info}}
1.3	1011
15.1	1012	(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
7.9	1013	\|=(% colspan="3" style="width: 707px;" %)AT+CHE
	1014	\|(% style="width:160px" %)Command Example\|(% style="width:198px" %)Function\|(% style="width:349px" %)Response
	1015	\|(% style="width:160px" %)AT+CHE=?\|(% style="width:198px" %)Get eight channels mode\|(% style="width:349px" %)1(((
1.3	1016	902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
	1017
	1018	OK
	1019	)))
7.9	1020	\|(% style="width:160px" %)AT+CHE=1\|(% style="width:198px" %)Set eight channels mode\|(% style="width:349px" %)OK
1.3	1021
7.9	1022	{{info}}
	1023	Downlink Command: 0x24
	1024	{{/info}}
1.3	1025
	1026	Format: Command Code (0x24) followed by 1 bytes channel value.
	1027
	1028	If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
	1029
7.9	1030	* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1
	1031	* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5
1.3	1032
	1033	== 7.20 Get or Set RXwindows1 timeout ==
	1034
	1035	Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
	1036
7.9	1037	{{info}}
	1038	AT Command: AT+RX1WTO
	1039	{{/info}}
1.3	1040
15.1	1041	(% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
7.9	1042	\|=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
	1043	\|(% style="width:163px" %)Command Example\|(% style="width:201px" %)Function\|(% style="width:93px" %)Response
	1044	\|(% style="width:163px" %)AT+RX1WTO=?\|(% style="width:201px" %)Get RXwindows1 timeout\|(% style="width:93px" %)14(((
1.3	1045	OK
	1046	)))
7.9	1047	\|(% style="width:163px" %)AT+RX1WTO=60\|(% style="width:201px" %)Set RXwindows1 timeout\|(% style="width:93px" %)OK
1.3	1048
15.4	1049	(((
	1050	AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
	1051	)))
1.3	1052
19.2	1053	[[image:image-20220526162535-1.png]]
1.3	1054
15.4	1055	(((
1.3	1056	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
21.1	1057
	1058
15.4	1059	)))
1.3	1060
	1061	== 7.21 Get or Set RXwindows2 timeout ==
	1062
	1063	Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
	1064
8.1	1065	{{info}}
	1066	AT Command: AT+RX2WTO
	1067	{{/info}}
1.3	1068
15.1	1069	(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
8.1	1070	\|=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
	1071	\|(% style="width:190px" %)Command Example\|(% style="width:199px" %)Function\|(% style="width:104px" %)Response
	1072	\|(% style="width:190px" %)AT+RX2WTO=?\|(% style="width:199px" %)Get RXwindows2 timeout\|(% style="width:104px" %)7(((
1.3	1073	OK
	1074	)))
8.1	1075	\|(% style="width:190px" %)AT+RX2WTO=20\|(% style="width:199px" %)Set RXwindows2 timeout\|(% style="width:104px" %)OK
1.3	1076
	1077	== 7.22 Setting up uplinkdwelltime (as923, au915) ==
	1078
	1079	Feature: Get or Set uplinkdwelltime
	1080
8.1	1081	{{info}}
	1082	AT Command: AT+DWELLT
	1083	{{/info}}
1.3	1084
15.1	1085	(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
8.1	1086	\|=(% colspan="3" style="width: 494px;" %)AT+DWELLT
	1087	\|(% style="width:183px" %)Command Example\|(% style="width:179px" %)Function\|(% style="width:131px" %)Response
	1088	\|(% style="width:183px" %)AT+DWELLT=?\|(% style="width:179px" %)Get uplinkdwelltime\|(% style="width:131px" %)1(((
1.3	1089	OK
	1090	)))
8.1	1091	\|(% style="width:183px" %)AT+DWELLT=0\|(% style="width:179px" %)Set uplinkdwelltime\|(% style="width:131px" %)OK
1.3	1092
8.1	1093	{{info}}
	1094	Downlink Command: 0x25
	1095	{{/info}}
1.3	1096
	1097	Format: Command Code (0x25) followed by 1 bytes state value.
	1098
	1099	If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
	1100
8.1	1101	* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1
	1102	* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0
1.3	1103
	1104	== 7.23 Set Packet Receiving Response Level ==
	1105
	1106	Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
	1107
	1108	RPL value:
	1109
8.1	1110	* AT+RPL=0: Device won't immediately reply any downlink commands from platform.
	1111	* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
	1112	* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
	1113	* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
	1114	* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1.3	1115
	1116	Case Analyes:
	1117
	1118	* For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
	1119	* For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
	1120	* For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
	1121
8.1	1122	{{info}}
	1123	AT Command: AT+RPL
	1124	{{/info}}
1.3	1125
15.1	1126	(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
8.1	1127	\|=(% colspan="3" style="width: 533px;" %)AT+RPL
	1128	\|(% style="width:160px" %)Command Example\|(% style="width:263px" %)Function\|(% style="width:109px" %)Response
	1129	\|(% style="width:160px" %)AT+RPL=?\|(% style="width:263px" %)Get packet receiving response level\|(% style="width:109px" %)1(((
1.3	1130	OK
	1131	)))
8.1	1132	\|(% style="width:160px" %)AT+RPL=0\|(% style="width:263px" %)Set packet receiving response level\|(% style="width:109px" %)OK
1.3	1133
8.1	1134	{{info}}
	1135	Downlink Command: 0x21
	1136	{{/info}}
1.3	1137
	1138	Format: Command Code (0x21) followed by 1 bytes level value.
	1139
	1140	If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
	1141
8.1	1142	* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1
	1143	* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2
1.3	1144
	1145	= 8. AT Commands Combination =
	1146
	1147	== 8.1 Set a fix RX2DR for downlink window ==
	1148
8.1	1149	* AT+ADR=0 ~-~-> Disable ADR first
	1150	* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate
1.3	1151
	1152	== 8.2 Use Downlink Command to set a fix uplink DR ==
	1153
8.1	1154	{{info}}
	1155	Downlink Command: 0x22000500
	1156	{{/info}}
1.3	1157
	1158	Same as:
	1159
19.4	1160	* AT+ADR=0 [[Reference>>\|\|anchor="H7.1AdaptiveDataRate"]]
	1161	* AT+DR=5 [[Reference>>\|\|anchor="H7.4DataRate"]]
	1162	* AT+TXP=0 [[Reference>>\|\|anchor="H7.14TransmitPower"]]

Wiki source code of End Device AT Commands and Downlink Command

Applications

Navigation