Skip to Content
Version 38.121 by Xiaoling on 2022/06/01 11:57
Show last authors
1 **Contents：**
2
3 {{toc/}}
4
5
6
7 = 1. Introduction =
8
9 Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10
11 * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
12 * **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
13
14 (((
15 **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
16
17 )))
18
19 = 2. How to use AT Commands or Downlink command =
20
21 * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 ** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25 ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26
27
28
29 = 3. Support End Node and firmware version =
30
31 (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
32 |=(% colspan="3" style="width: 963px;" %)(((
33 Dragino STM32 base hardware Firmware / LoRaWAN stack list
34 )))
35 |(% style="width:187px" %)(((
36 **Model**
37 )))|(% style="width:330px" %)(((
38 **Description**
39 )))|(% style="width:445px" %)(((
40 **Firmware Version <~-~-> Stack Version**
41 )))
42 |(% style="width:187px" %)(((
43 [[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
44 )))|(% style="width:330px" %)(((
45 Open Source Generic LoRaWAN Sensor Node
46 )))|(% style="width:445px" %)(((
47 (((
48 LSN50 v1.6.0 <~-~-> DR-LWS-003;
49 )))
50
51 (((
52 (((
53 LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
54 )))
55 )))
56 )))
57 |(% style="width:187px" %)(((
58 [[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
59 )))|(% style="width:330px" %)(((
60 LoRaWAN GPS Tracker
61 )))|(% style="width:445px" %)(((
62 (((
63 LGT92 v1.6.3 <~-~-> DR-LWS-003;
64 )))
65
66 (((
67 (((
68 LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
69 )))
70 )))
71 )))
72 |(% style="width:187px" %)(((
73 [[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
74 )))|(% style="width:330px" %)(((
75 LoRaWAN BLE Indoor Tracker
76 )))|(% style="width:445px" %)(((
77 LBT1 v1.0 <~-~-> DR-LWS-005;
78 )))
79 |(% style="width:187px" %)(((
80 [[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
81 )))|(% style="width:330px" %)(((
82 LoRaWAN RS485 Modbus Converter
83 )))|(% style="width:445px" %)(((
84 RS485-LN v1.3 <~-~-> DR-LWS-005;
85 )))
86 |(% style="width:187px" %)(((
87 [[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
88 )))|(% style="width:330px" %)(((
89 LoRaWAN Temperature & Humidity Sensor
90 )))|(% style="width:445px" %)(((
91 (((
92 LHT65 v1.7 <~-~-> DR-LWS-003;
93 )))
94
95 (((
96 (((
97 LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
98 )))
99 )))
100 )))
101
102
103
104 = 4. System Management Commands =
105
106 == 4.1 Change Uplink Interval ==
107
108 Feature: Change LoRaWAN End Node Transmit Interval.
109
110 (% class="box infomessage" %)
111 (((
112 **AT Command: AT+TDC**
113 )))
114
115 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
116 |=(% colspan="3" style="width: 724px;" %)AT+TDC
117 |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
118 |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
119 OK
120
121 the interval is 30000ms = 30s
122 )))
123 |(% style="width:165px" %)AT+TDC=60000|(% style="width:227px" %)Set Transmit Interval|(% style="width:329px" %)OK(((
124 Set transmit interval to 60000ms = 60 seconds
125 )))
126
127 {{info}}
128 **Downlink Command: 0x01**
129 {{/info}}
130
131 (((
132 Format: Command Code (0x01) followed by 3 bytes time value.
133 )))
134
135 (((
136 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
137 )))
138
139 * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
140 * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
141
142
143
144 == 4.2 Reboot End Node ==
145
146 Feature: Reboot End Node to perform a new OTAA or ABP Join.
147
148 {{info}}
149 **AT Command: ATZ**
150 {{/info}}
151
152 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
153 |=(% colspan="3" %)ATZ: Trig a reset of the MCU
154 |**Command Example**|**Function**|**Response**
155 |ATZ|Reset MCU|(((
156 Device reset and show booting info
157
158 LSN50 Device/LoRa ST Module
159
160 Image Version: XX
161
162 Frequency Band: XX
163
164 DevEui= XX XX XX XX XX XX XX XX
165
166 <followed by the Tx and Rx information>
167 )))
168
169 {{info}}
170 **Downlink Command: 0x04**
171 {{/info}}
172
173 (((
174 Format: Command Code (0x04) followed by FF.
175 )))
176
177 (((
178 If the downlink payload=**04FF**, the end node will reboot.
179
180
181 )))
182
183 == 4.3 Reset to factory Default ==
184
185 Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
186
187 {{info}}
188 **AT Command: AT+FDR**
189 {{/info}}
190
191 (% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
192 |=(% colspan="3" style="width: 828px;" %)Reset to factory default
193 |(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
194 |(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
195 Device reset to factory default parameters and show booting info
196
197 LSN50 Device/LoRa ST Module
198
199 Image Version: XX
200
201 Frequency Band: XX
202
203 DevEui= XX XX XX XX XX XX XX XX
204
205 Please set the parameters or reset Device to apply change
206 )))
207
208 {{info}}
209 **Downlink Command: 0x04**
210 {{/info}}
211
212 (((
213 Format: Command Code (0x04) followed by FE.
214 )))
215
216 (((
217 If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
218 )))
219
220
221 == 4.4 Show Firmware Version ==
222
223 Feature: Show firmware version. No downlink command yet.
224
225 {{info}}
226 **AT Command: AT+VER**
227 {{/info}}
228
229 (% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
230 |=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
231 |(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
232 |(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
233 1.3 EU868
234
235 OK
236 )))
237
238 {{info}}
239 **Downlink Command: 0x26 (Valid in 006 stack)**
240 {{/info}}
241
242 (((
243 Downlink Format: 0x26
244 )))
245
246 (((
247 Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
248 )))
249
250 (((
251 **xx: Software Type:**
252 )))
253
254 * 0x00 01: LGT92 Version
255 * 0x00 02: LBT1
256 * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
257
258 (((
259 **yy: Frequency Band:**
260 )))
261
262 * 0x01: EU868
263 * 0x02: US915
264 * 0x03: IN865
265 * 0x04: AU915
266 * 0x05: KZ865
267 * 0x06: RU864
268 * 0x07: AS923
269 * 0x08: AS923-1
270 * 0x09: AS923-2
271 * 0xa0: AS923-3
272
273 (((
274 **zz: Subband**
275 )))
276
277 firmware version: v1.1.0 ~-~-> 110
278
279
280 == 4.5 Show System Configure ==
281
282 Feature: Show All configure. No downlink command yet.
283
284 {{info}}
285 **AT Command: AT+CFG**
286 {{/info}}
287
288 (% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
289 |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
290 |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
291 |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
292 AT+DEUI = XX XX XX XX XX XX XX XX
293
294 AT+DADDR=XXXXXXXX
295
296 ……….
297
298 AT+RX2WTO=X
299
300 AT+CHS=868100000
301
302 OK
303 )))
304
305
306
307 = 5. Keys, IDs and EUIs management =
308
309 == 5.1 Application EUI ==
310
311 Feature: Get or Set the Application EUI.
312
313 {{info}}
314 **AT Command: AT+APPEUI**
315 {{/info}}
316
317 (% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
318 |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
319 |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
320 |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
321 OK
322 )))
323 |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
324
325
326
327 == 5.2 Application Key ==
328
329 Feature: Get or Set the Application Key.
330
331 {{info}}
332 **AT Command: AT+APPKEY**
333 {{/info}}
334
335 (% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
336 |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
337 |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
338 |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
339 OK
340 )))
341 |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
342
343
344
345 == 5.3 Application Session Key ==
346
347 Feature: Get or Set the Application Session Key.
348
349 {{info}}
350 **AT Command: AT+APPSKEY**
351 {{/info}}
352
353 (% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
354 |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
355 |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
356 |(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
357 OK
358 )))
359 |(% style="width:451px" %)AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|(% style="width:231px" %)Set the Application Session Key|(% style="width:354px" %)(While Error in format, return AT_PARAM_ERROR)(((
360 OK
361 )))
362
363
364
365 == 5.4 Device Address ==
366
367 Feature: Get or Set the Device Address.
368
369 {{info}}
370 **AT Command: AT+DADDR**
371 {{/info}}
372
373 (% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
374 |=(% colspan="3" style="width: 792px;" %)AT+DADDR
375 |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
376 |(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
377 A8 40 41 FF
378
379 OK
380 )))
381 |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
382
383
384
385 == 5.5 Device EUI ==
386
387 Feature: Get or Set the Device EUI.
388
389 {{info}}
390 **AT Command: AT+DEUI**
391 {{/info}}
392
393 (% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
394 |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
395 |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
396 |(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
397 OK
398 )))
399 |(% style="width:250px" %)AT+DEUI=A8 40 41 FF FF 12 34 56|(% style="width:147px" %)Set the Device EUI.|(% style="width:634px" %)(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
400 OK
401 )))
402
403
404
405 == 5.6 Network ID ==
406
407 Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
408
409 {{info}}
410 **AT Command: AT+NWKID**
411 {{/info}}
412
413 (% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
414 |=(% colspan="3" style="width: 445px;" %)AT+NWKID
415 |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
416 |(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
417 OK
418 )))
419 |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
420
421
422
423 == 5.7 Network Session Key ==
424
425 Feature: Get or Set the Network Session Key
426
427 {{info}}
428 **AT Command: AT+NWKSKEY**
429 {{/info}}
430
431 (% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
432 |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
433 |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
434 |(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
435 OK
436 )))
437 |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
438
439
440
441 = 6. Joining and sending date on LoRaWAN network =
442
443 == 6.1 Confirm Mode ==
444
445 Feature: Get or Set the confirmation mode (0-1).
446
447 {{info}}
448 **AT Command: AT+CFM**
449 {{/info}}
450
451 (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
452 |=(% colspan="3" style="width: 707px;" %)AT+CFM
453 |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
454 |(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
455 OK
456 )))
457 |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
458 |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
459
460 Downlink Command: 0x05
461
462 Format: Command Code (0x05) followed by 2 bytes mode value.
463
464 If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
465
466 * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
467 * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
468
469
470
471 == 6.2 Confirm Status ==
472
473 Feature: Get confirmation status of the last AT+SEND (0-1).
474
475 {{info}}
476 **AT Command: AT+CFS**
477 {{/info}}
478
479 (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
480 |=(% colspan="3" style="width: 531px;" %)AT+CFS
481 |(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
482 |(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
483 OK
484 )))
485
486
487
488 == 6.3 Join LoRa® Network ==
489
490 Feature: Join network.
491
492 {{info}}
493 **AT Command: AT+JOIN**
494 {{/info}}
495
496 (% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
497 |=(% colspan="3" style="width: 644px;" %)AT+JOIN
498 |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
499 |(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
500 OK
501
502 While Error in format, return AT_BUSY_ERROR
503 )))
504
505
506
507 == 6.4 LoRa® Network Join Mode ==
508
509 Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
510
511 {{info}}
512 **AT Command: AT+NJM**
513 {{/info}}
514
515 (% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
516 |=(% colspan="3" style="width: 750px;" %)AT+NJM
517 |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
518 |(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
519 OK
520 )))
521 |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
522 |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
523
524 {{info}}
525 **Downlink Command: 0x20**
526 {{/info}}
527
528 Format: Command Code (0x20) followed by 1 bytes mode value.
529
530 If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
531
532 * **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
533 * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
534
535
536
537 == 6.5 LoRa® Network Join Status ==
538
539 Feature: LoRa® Network Join Status.
540
541 {{info}}
542 **AT Command: AT+NJS**
543 {{/info}}
544
545 (% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
546 |=(% colspan="3" style="width: 495px;" %)AT+NJS
547 |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
548 |(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
549 OK
550 )))
551
552
553
554 == 6.6 Print Last Received Data in Raw Format ==
555
556 Feature: Print Last Received Data in Raw Format<port:data>.
557
558 {{info}}
559 **AT Command: AT+RECV**
560 {{/info}}
561
562 (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
563 |=(% colspan="3" style="width: 584px;" %)AT+RECV
564 |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
565 |(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
566 OK
567 )))
568
569
570
571 == 6.7 Print Last Received Data in Binary Format ==
572
573 Feature: Print Last Received Data in Binary Format<port:data>.
574
575 {{info}}
576 **AT Command: AT+RECVB**
577 {{/info}}
578
579 (% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
580 |=(% colspan="3" style="width: 790px;" %)AT+RECVB
581 |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
582 |(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
583 OK
584 )))
585
586
587
588 == 6.8 Send Text Data ==
589
590 Feature: Send Text Data<port:data>.
591
592 {{info}}
593 **AT Command: AT+SEND**
594 {{/info}}
595
596 (% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
597 |=(% colspan="3" style="width: 988px;" %)AT+SEND
598 |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
599 |(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
600 While Error in format, return
601
602 AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
603
604
605 )))
606
607
608
609 == 6.9 Send Hexadecimal Data ==
610
611 Feature: Send hexadecimal data along with the application port.
612
613 {{info}}
614 **AT Command: AT+SENDB**
615 {{/info}}
616
617 (% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
618 |=(% colspan="3" style="width: 1117px;" %)AT+SENDB
619 |(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
620 |(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
621 |(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
622 AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
623
624
625 )))
626
627
628
629 = 7. LoRaWAN network management =
630
631 == 7.1 Adaptive Data Rate ==
632
633 Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
634
635 {{info}}
636 **AT Command: AT+ADR**
637 {{/info}}
638
639 (% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
640 |=(% colspan="3" style="width: 680px;" %)AT+ADR
641 |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
642 |(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1(((
643 OK
644 )))
645 |(% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)OK
646 |(% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)While Error in format, return(((
647 AT_PARAM_ERROR
648 )))
649
650 {{info}}
651 **Downlink Command: 0x22**
652 {{/info}}
653
654
655 If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
656
657 * **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
658 * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
659
660 == 7.2 LoRa® Class ==
661
662 Feature: Get or Set the Device Class(Currently only support class A, class C).
663
664 {{info}}
665 **AT Command:AT+CLASS**
666 {{/info}}
667
668 (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
669 |=(% colspan="3" style="width: 504px;" %)AT+CLASS
670 |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
671 |(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
672 OK
673 )))
674 |(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
675
676 )))
677
678 == 7.3 Duty Cycle Setting ==
679
680 Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
681
682 {{info}}
683 **AT Command:AT+DCS**
684 {{/info}}
685
686 (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
687 |=(% colspan="3" style="width: 512px;" %)AT+DCS
688 |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
689 |(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
690 OK
691 )))
692 |(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
693
694 )))
695
696 == 7.4 Data Rate ==
697
698 Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
699
700 {{info}}
701 **AT Command: AT+DR**
702 {{/info}}
703
704 (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
705 |=(% colspan="3" style="width: 463px;" %)AT+DR
706 |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
707 |(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
708 OK
709 )))
710 |(% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((
711
712 )))
713
714 {{info}}
715 **Downlink Command: 0x2200aaFF**
716 {{/info}}
717
718
719 If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
720
721 * **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
722 * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
723
724 == 7.5 Frame Counter Downlink ==
725
726 Feature: Get or Set the Frame Counter Downlink.
727
728 {{info}}
729 **AT Command:AT+FCD**
730 {{/info}}
731
732 (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
733 |=(% colspan="3" style="width: 690px;" %)AT+FCD
734 |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
735 |(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
736 OK
737 )))
738 |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
739 OK
740
741
742 )))
743
744 == 7.6 Frame Counter Uplink ==
745
746 Feature: Get or Set the Frame Counter Uplink.
747
748 {{info}}
749 **AT Command:AT+FCU**
750 {{/info}}
751
752 (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
753 |=(% colspan="3" style="width: 531px;" %)AT+FCU
754 |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
755 |(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
756 OK
757 )))
758 |(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
759
760 )))
761
762 == 7.7 Join Accept Delay1 ==
763
764 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
765
766 {{info}}
767 **AT Command:AT+JN1DL**
768 {{/info}}
769
770 (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
771 |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
772 |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
773 |(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
774 OK
775 )))
776 |(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
777
778 )))
779
780 == 7.8 Join Accept Delay2 ==
781
782 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
783
784 {{info}}
785 **AT Command:AT+JN2DL**
786 {{/info}}
787
788 (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
789 |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
790 |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
791 |(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
792 OK
793 )))
794 |(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
795
796 )))
797
798 == 7.9 Public Network Mode ==
799
800 Feature: Get or Set the public network mode. (0: off, 1: on)
801
802 {{info}}
803 **AT Command:AT+PNM**
804 {{/info}}
805
806 (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
807 |=(% colspan="3" style="width: 664px;" %)AT+PNM
808 |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
809 |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
810 OK
811 )))
812 |(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
813 OK
814
815
816 )))
817
818 == 7.10 Receive Delay1 ==
819
820 Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
821
822 {{info}}
823 **AT Command:AT+RX1DL**
824 {{/info}}
825
826 (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
827 |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
828 |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
829 |(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
830 OK
831 )))
832 |(% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((
833
834 )))
835
836 == 7.11 Receive Delay2 ==
837
838 Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
839
840 {{info}}
841 **AT Command:AT+RX2DL**
842 {{/info}}
843
844 (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
845 |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
846 |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
847 |(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
848 OK
849 )))
850 |(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
851
852 )))
853
854 == 7.12 Rx2 Window Data Rate ==
855
856 Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
857
858 {{info}}
859 **AT Command:AT+RX2DR**
860 {{/info}}
861
862 (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
863 |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
864 |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
865 |(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
866 OK
867 )))
868 |(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
869
870 )))
871
872 == 7.13 Rx2 Window Frequency ==
873
874 Feature: Get or Set the Rx2 window frequency
875
876 {{info}}
877 **AT Command:AT+RX2FQ**
878 {{/info}}
879
880 (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
881 |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
882 |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
883 |(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
884 OK
885 )))
886 |(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
887
888 )))
889
890 == 7.14 Transmit Power ==
891
892 Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
893
894 {{info}}
895 **AT Command:AT+TXP**
896 {{/info}}
897
898 (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
899 |=(% colspan="3" style="width: 462px;" %)AT+TXP
900 |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
901 |(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
902 OK
903 )))
904 |(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
905
906 )))
907
908 Downlink Payload. The 4th byte of 0x22 downlink.
909
910 If the downlink payload=22000100, it means setting the TXP to 0.
911
912 * **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
913 * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
914
915 == 7.15 RSSI of the Last Received Packet ==
916
917 Feature: Get or Set the Rx2 window frequency
918
919 {{info}}
920 **AT Command:AT+RSSI**
921 {{/info}}
922
923 (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
924 |=(% colspan="3" style="width: 554px;" %)AT+RSSI
925 |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
926 |(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
927 OK
928 )))
929
930 == 7.16 SNR of the Last Received Packet ==
931
932 Feature: Get the SNR of the last received packet
933
934 {{info}}
935 **AT Command:AT+SNR**
936 {{/info}}
937
938 (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
939 |=(% colspan="3" style="width: 568px;" %)AT+SNR
940 |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
941 |(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
942 OK
943 )))
944
945 == 7.17 Application Port ==
946
947 Feature: Get or set the application port.
948
949 {{info}}
950 **AT Command: AT+PORT**
951 {{/info}}
952
953 (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
954 |=(% colspan="3" style="width: 497px;" %)AT+PORT
955 |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
956 |(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
957 OK
958 )))
959 |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
960
961 {{info}}
962 **Downlink Command: 0x23**
963 {{/info}}
964
965 Format: Command Code (0x23) followed by 1 bytes port value.
966
967 If the downlink payload=2301, it means set the application port to 1, while type code is 23.
968
969 * **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
970 * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
971
972 == 7.18 Single Channel Mode ==
973
974 Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
975
976 {{info}}
977 **AT Command: AT+CHS**
978 {{/info}}
979
980 (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
981 |=(% colspan="3" style="width: 600px;" %)AT+CHS
982 |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
983 |(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
984 OK
985 )))
986 |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
987
988 == 7.19 Eight Channel Mode ==
989
990 Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
991
992 {{info}}
993 **AT Command: AT+CHE**
994 {{/info}}
995
996 (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
997 |=(% colspan="3" style="width: 707px;" %)AT+CHE
998 |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
999 |(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
1000 902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
1001
1002 OK
1003 )))
1004 |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1005
1006 {{info}}
1007 **Downlink Command: 0x24**
1008 {{/info}}
1009
1010 Format: Command Code (0x24) followed by 1 bytes channel value.
1011
1012 If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1013
1014 * **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1015 * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1016
1017 == 7.20 Get or Set RXwindows1 timeout ==
1018
1019 Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1020
1021 {{info}}
1022 **AT Command: AT+RX1WTO**
1023 {{/info}}
1024
1025 (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1026 |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1027 |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
1028 |(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
1029 OK
1030 )))
1031 |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1032
1033 (((
1034 **AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1035 )))
1036
1037 [[image:image-20220526162535-1.png]]
1038
1039 (((
1040 Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1041
1042
1043 )))
1044
1045 == 7.21 Get or Set RXwindows2 timeout ==
1046
1047 Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1048
1049 {{info}}
1050 **AT Command: AT+RX2WTO**
1051 {{/info}}
1052
1053 (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1054 |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1055 |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
1056 |(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
1057 OK
1058 )))
1059 |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1060
1061 == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1062
1063 Feature: Get or Set uplinkdwelltime
1064
1065 {{info}}
1066 **AT Command: AT+DWELLT**
1067 {{/info}}
1068
1069 (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1070 |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1071 |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
1072 |(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
1073 OK
1074 )))
1075 |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1076
1077 {{info}}
1078 **Downlink Command: 0x25**
1079 {{/info}}
1080
1081 Format: Command Code (0x25) followed by 1 bytes state value.
1082
1083 If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1084
1085 * **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1086 * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1087
1088 == 7.23 Set Packet Receiving Response Level ==
1089
1090 Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1091
1092 RPL value:
1093
1094 * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1095 * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1096 * **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1097 * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1098 * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1099
1100 Case Analyes:
1101
1102 * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1103 * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1104 * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1105
1106 {{info}}
1107 **AT Command: AT+RPL**
1108 {{/info}}
1109
1110 (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1111 |=(% colspan="3" style="width: 533px;" %)AT+RPL
1112 |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1113 |(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
1114 OK
1115 )))
1116 |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1117
1118 {{info}}
1119 **Downlink Command: 0x21**
1120 {{/info}}
1121
1122 Format: Command Code (0x21) followed by 1 bytes level value.
1123
1124 If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1125
1126 * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1127 * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1128
1129 = 8. AT Commands Combination =
1130
1131 == 8.1 Set a fix RX2DR for downlink window ==
1132
1133 * **AT+ADR=0 **~-~-> Disable ADR first
1134 * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1135
1136 == 8.2 Use Downlink Command to set a fix uplink DR ==
1137
1138 {{info}}
1139 **Downlink Command: 0x22000500**
1140 {{/info}}
1141
1142 Same as:
1143
1144 * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1145 * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1146 * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]