Last modified by kai on 2024/09/06 10:00
<
From version < 63.40 >
edited by Xiaoling
on 2023/05/29 14:50
To version < 7.5 >
edited by Xiaoling
on 2022/05/11 10:13
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,120 +1,57 @@
1 - **Table of** **Contents：**
1 +Contens
2 2  
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 -
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 -* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
10 +* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
11 +* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 -(((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 -)))
14 +
18 18  
19 -
20 20  = 2. How to use AT Commands or Downlink command =
21 21  
18 +* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
19 +* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
20 +** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
21 +** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
22 +** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
22 22  
23 -* **AT Command** : See Devices User Manual for how to connect to device via USB TTL adapter and use. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
24 -* **LoRaWAN Downlink Command**: The gateway transfer downlink command in HEX format. This page shows the Downlink Command In HEX format. Please note some LoRaWAN servers use base64 as downlink code so user need to convert HEX to Base64 and use. Below are references for how to use downlink command:
25 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
26 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]], [[How to Convert>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.1ConvertHEXtoBase64]]?
27 -** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
28 -
29 -(% style="display:none" %) (%%)
30 -
31 31  = 3. Support End Node and firmware version =
32 32  
33 -
34 -Dragino STM32 base hardware Firmware / LoRaWAN stack list
35 -
36 -(% border="1" cellspacing="4" style="background-color:#f2f2f2; width:966px" %)
37 -|(% style="background-color:#4f81bd; color:white; width:187px" %)(((
38 -**Model**
39 -)))|(% style="background-color:#4f81bd; color:white; width:330px" %)(((
40 -**Description**
41 -)))|(% style="background-color:#4f81bd; color:white; width:445px" %)(((
42 -**Firmware Version <~-~-> Stack Version**
43 -)))
44 -|(% style="width:187px" %)(((
45 -[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
46 -)))|(% style="width:330px" %)(((
47 -Open Source Generic LoRaWAN Sensor Node
48 -)))|(% style="width:445px" %)(((
49 -(((
50 -LSN50 v1.6.0 <~-~-> DR-LWS-003;
51 -)))
52 -
53 -(((
54 -(((
26 +(% style="background-color:#ffffcc; color:green; width:995.222px" %)
27 +|=(% colspan="3" style="width: 992px;" %)Dragino STM32 base hardware Firmware / LoRaWAN stack list
28 +|(% style="width:187px" %)**Model**|(% style="width:349px" %)**Description**|(% style="width:453px" %)**Firmware Version <~-~-> Stack Version**
29 +|(% style="width:187px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:349px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:453px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;(((
55 55  LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
56 56  )))
57 -)))
58 -)))
59 -|(% style="width:187px" %)(((
60 -[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
61 -)))|(% style="width:330px" %)(((
62 -LoRaWAN GPS Tracker
63 -)))|(% style="width:445px" %)(((
64 -(((
65 -LGT92 v1.6.3 <~-~-> DR-LWS-003;
66 -)))
67 -
68 -(((
69 -(((
32 +|(% style="width:187px" %)[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],|(% style="width:349px" %)LoRaWAN GPS Tracker|(% style="width:453px" %)LGT92 v1.6.3 <~-~-> DR-LWS-003;(((
70 70  LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
71 71  )))
72 -)))
73 -)))
74 -|(% style="width:187px" %)(((
75 -[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
76 -)))|(% style="width:330px" %)(((
77 -LoRaWAN BLE Indoor Tracker
78 -)))|(% style="width:445px" %)(((
79 -LBT1 v1.0 <~-~-> DR-LWS-005;
80 -)))
81 -|(% style="width:187px" %)(((
82 -[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
83 -)))|(% style="width:330px" %)(((
84 -LoRaWAN RS485 Modbus Converter
85 -)))|(% style="width:445px" %)(((
86 -RS485-LN v1.3 <~-~-> DR-LWS-005;
87 -)))
88 -|(% style="width:187px" %)(((
89 -[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
90 -)))|(% style="width:330px" %)(((
91 -LoRaWAN Temperature & Humidity Sensor
92 -)))|(% style="width:445px" %)(((
93 -(((
94 -LHT65 v1.7 <~-~-> DR-LWS-003;
95 -)))
96 -
97 -(((
98 -(((
35 +|(% style="width:187px" %)[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],|(% style="width:349px" %)LoRaWAN BLE Indoor Tracker|(% style="width:453px" %)LBT1 v1.0 <~-~-> DR-LWS-005;
36 +|(% style="width:187px" %)[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],|(% style="width:349px" %)LoRaWAN RS485 Modbus Converter|(% style="width:453px" %)RS485-LN v1.3 <~-~-> DR-LWS-005;
37 +|(% style="width:187px" %)[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],|(% style="width:349px" %)LoRaWAN Temperature & Humidity Sensor|(% style="width:453px" %)LHT65 v1.7 <~-~-> DR-LWS-003;(((
99 99  LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
100 100  )))
101 -)))
102 -)))
103 103  
104 -(% style="display:none" %) (%%)
105 -
106 106  = 4. System Management Commands =
107 107  
108 108  == 4.1 Change Uplink Interval ==
109 109  
110 -
111 111  Feature: Change LoRaWAN End Node Transmit Interval.
112 112  
47 +(% class="box infomessage" %)
48 +(((
49 +**AT Command: AT+TDC**
50 +)))
113 113  
114 -(% style="color:blue" %)**AT Command: AT+TDC**
115 -
116 -(% border="1" style="background-color:#f2f2f2; width:727.222px" %)
117 -|(% style="background-color:#4f81bd; color:white; width:165px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:227px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:329px" %)**Response**
52 +(% style="background-color:#ffffcc; color:green; width:727.222px" %)
53 +|=(% colspan="3" style="width: 724px;" %)AT+TDC
54 +|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
118 118  |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
119 119  OK
120 120  
... ... @@ -124,32 +124,29 @@
124 124  Set transmit interval to 60000ms = 60 seconds
125 125  )))
126 126  
127 -(((
128 -(% style="color:blue" %)**Downlink Command: 0x01**
64 +{{info}}
65 +**Downlink Command: 0x01**
66 +{{/info}}
129 129  
130 130  Format: Command Code (0x01) followed by 3 bytes time value.
131 -)))
132 132  
133 -(((
134 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
135 -)))
70 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
136 136  
137 -* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
138 -* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
72 +* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
73 +* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
139 139  
140 -(% style="display:none" %) (%%)
141 -
142 142  == 4.2 Reboot End Node ==
143 143  
144 -
145 145  Feature: Reboot End Node to perform a new OTAA or ABP Join.
146 146  
79 +{{info}}
80 +**AT Command: ATZ**
81 +{{/info}}
147 147  
148 -(% style="color:blue" %)**AT Command: ATZ  ~/~/ **(%%)Trig a reset of the MCU
149 -
150 -(% border="1" style="background-color:#f2f2f2; width:546px" %)
151 -|(% style="background-color:#4f81bd; color:white; width:157px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:92px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:294px" %)**Response**
152 -|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
83 +(% border="0" style="background-color:#ffffcc; color:green; width:727.222px" %)
84 +|=(% colspan="3" %)ATZ: Trig a reset of the MCU
85 +|**Command Example**|**Function**|**Response**
86 +|ATZ|Reset MCU|(((
153 153  Device reset and show booting info
154 154  
155 155  LSN50 Device/LoRa ST Module
... ... @@ -163,28 +163,26 @@
163 163  <followed by the Tx and Rx information>
164 164  )))
165 165  
166 -(% style="color:blue" %)**Downlink Command: 0x04**
100 +{{info}}
101 +**Downlink Command: 0x04**
102 +{{/info}}
167 167  
168 -(((
169 169  Format: Command Code (0x04) followed by FF.
170 -)))
171 171  
172 -(((
173 -If the downlink payload=**04FF**, the end node will reboot.
174 -)))
106 +If the downlink payload=**04FF**, the end node will reboot.
175 175  
176 -
177 177  == 4.3 Reset to factory Default ==
178 178  
179 -
180 180  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
181 181  
112 +{{info}}
113 +**AT Command: AT+FDR**
114 +{{/info}}
182 182  
183 -(% style="color:blue" %)**AT Command: AT+FDR  ~/~/  **(%%)Reset to factory default
184 -
185 -(% border="1" style="background-color:#f2f2f2; width:789px" %)
186 -|(% style="background-color:#4f81bd; color:white; width:154px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:175px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:456px" %)**Response**
187 -|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
116 +(% style="background-color:#ffffcc; color:green; width:831.222px" %)
117 +|=(% colspan="3" style="width: 828px;" %)Reset to factory default
118 +|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
119 +|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
188 188  Device reset to factory default parameters and show booting info
189 189  
190 190  LSN50 Device/LoRa ST Module
... ... @@ -198,59 +198,48 @@
198 198  Please set the parameters or reset Device to apply change
199 199  )))
200 200  
201 -(% style="color:blue" %)**Downlink Command: 0x04**
133 +{{info}}
134 +**Downlink Command: 0x04**
135 +{{/info}}
202 202  
203 -(((
204 204  Format: Command Code (0x04) followed by FE.
205 -)))
206 206  
207 -(((
208 208  If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
209 -)))
210 210  
211 211  
212 212  == 4.4 Show Firmware Version ==
213 213  
214 -
215 215  Feature: Show firmware version. No downlink command yet.
216 216  
146 +{{info}}
147 +**AT Command: AT+VER**
148 +{{/info}}
217 217  
218 -(% style="color:blue" %)**AT Command: AT+VER  ~/~/   **(%%)Image Version and Frequency Band
219 -
220 -(% border="1" style="background-color:#f2f2f2; width:542px" %)
221 -|(% style="background-color:#4f81bd; color:white; width:157px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:295px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:86px" %)**Response**
222 -|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
150 +(% style="background-color:#ffffcc; color:green" %)
151 +|=(% colspan="3" %)AT+VER: Image Version and Frequency Band
152 +|**Command Example**|**Function**|**Response**
153 +|AT+VER=?|Show Image version and Frequency Band|(((
223 223  1.3 EU868
224 224  
225 225  OK
226 226  )))
227 227  
228 -(% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
159 +{{info}}
160 +**Downlink Command: 0x26 (Valid in 006 stack)**
161 +{{/info}}
229 229  
230 -(((
231 231  Downlink Format: 0x26
232 -)))
233 233  
234 -(((
235 235  Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
236 -)))
237 237  
238 -(((
239 -
167 +**xx: Software Type:**
240 240  
241 -(% style="color:#037691" %)**xx: Software Type:**
242 -)))
243 -
244 244  * 0x00 01: LGT92 Version
245 245  * 0x00 02: LBT1
246 246  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
247 247  
248 -(((
249 -
173 +**yy: Frequency Band:**
250 250  
251 -(% style="color:#037691" %)**yy: Frequency Band:**
252 -)))
253 -
254 254  * 0x01: EU868
255 255  * 0x02: US915
256 256  * 0x03: IN865
... ... @@ -262,680 +262,514 @@
262 262  * 0x09: AS923-2
263 263  * 0xa0: AS923-3
264 264  
265 -(((
266 -
186 +**zz: Subband**
267 267  
268 -(% style="color:#037691" %)**zz: Subband**
269 -)))
270 -
271 271  firmware version: v1.1.0 ~-~-> 110
272 272  
273 273  
274 274  == 4.5 Show System Configure ==
275 275  
276 -
277 277  Feature: Show All configure. No downlink command yet.
278 278  
195 +{{info}}
196 +**AT Command: AT+CFG**
197 +{{/info}}
279 279  
280 -(% style="color:blue" %)**AT Command: AT+CFG  ~/~/ **(%%)Print all configurations
281 -
282 -(% border="1" style="background-color:#f2f2f2; width:599.222px" %)
283 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:154px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:280px" %)**Response**
199 +(% style="background-color:#ffffcc; color:green; width:599.222px" %)
200 +|=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
201 +|(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
284 284  |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
285 285  AT+DEUI = XX XX XX XX XX XX XX XX
204 +
286 286  AT+DADDR=XXXXXXXX
206 +
287 287  ……….
208 +
288 288  AT+RX2WTO=X
210 +
289 289  AT+CHS=868100000
212 +
290 290  OK
291 291  )))
292 292  
293 -(% style="display:none" %) (%%)
294 294  
295 295  = 5. Keys, IDs and EUIs management =
296 296  
297 297  == 5.1 Application EUI ==
298 298  
299 -
300 300  Feature: Get or Set the Application EUI.
301 301  
223 +{{info}}
224 +**AT Command: AT+APPEUI**
225 +{{/info}}
302 302  
303 -(% style="color:blue" %)**AT Command: AT+APPEUI**
304 -
305 -(% border="1" style="background-color:#f2f2f2; width:686.222px" %)
306 -|(% style="background-color:#4f81bd; color:white; width:305px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:186px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:191px" %)**Response**
227 +(% style="background-color:#ffffcc; color:green; width:686.222px" %)
228 +|=(% colspan="3" style="width: 683px;" %)AT+APPEUI
229 +|(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
307 307  |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
308 308  OK
309 309  )))
310 310  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
311 311  
312 -(% style="display:none" %) (%%)
313 -
314 314  == 5.2 Application Key ==
315 315  
316 -
317 317  Feature: Get or Set the Application Key.
318 318  
239 +{{info}}
240 +**AT Command: AT+APPKEY**
241 +{{/info}}
319 319  
320 -(% style="color:blue" %)**AT Command: AT+APPKEY**
321 -
322 -(% border="1" style="background-color:#f2f2f2; width:976.222px" %)
323 -|(% style="background-color:#4f81bd; color:white; width:441px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:180px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:350px" %)**Response**
243 +(% style="background-color:#ffffcc; color:green; width:976.222px" %)
244 +|=(% colspan="3" style="width: 973px;" %)AT+APPKEY
245 +|(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
324 324  |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
325 325  OK
326 326  )))
327 327  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
328 328  
329 -(% style="display:none" %) (%%)
330 -
331 331  == 5.3 Application Session Key ==
332 332  
333 -
334 334  Feature: Get or Set the Application Session Key.
335 335  
255 +AT Command: AT+APPSKEY
336 336  
337 -(% style="color:blue" %)**AT Command: AT+APPSKEY**
338 -
339 -(% border="1" style="background-color:#f2f2f2; width:1040.22px" %)
340 -|(% style="background-color:#4f81bd; color:white; width:451px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:231px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:354px" %)**Response**
341 -|(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
257 +|=(% colspan="3" %)AT+APPSKEY
258 +|**Command Example**|**Function**|**Response**
259 +|AT+APPSKEY=?|Get the Application Session Key|00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
342 342  OK
343 343  )))
344 -|(% style="width:451px" %)AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|(% style="width:231px" %)Set the Application Session Key|(% style="width:354px" %)(While Error in format, return AT_PARAM_ERROR)(((
262 +|AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|Set the Application Session Key.|(While Error in format, return AT_PARAM_ERROR)(((
345 345  OK
346 346  )))
347 347  
348 -(% style="display:none" %) (%%)
349 -
350 350  == 5.4 Device Address ==
351 351  
352 -
353 353  Feature: Get or Set the Device Address.
354 354  
270 +AT Command: AT+DADDR
355 355  
356 -(% style="color:blue" %)**AT Command: AT+DADDR**
357 -
358 -(% border="1" style="background-color:#f2f2f2; width:795.222px" %)
359 -|(% style="background-color:#4f81bd; color:white; width:192px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:241px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:359px" %)**Response**
360 -|(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
272 +|=(% colspan="3" %)AT+DADDR
273 +|**Command Example**|**Function**|**Response**
274 +|AT+DADDR=?|Get the Application Session Key.|(While Error in format, return AT_PARAM_ERROR)(((
361 361  A8 40 41 FF
362 362  
363 363  OK
364 364  )))
365 -|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
279 +|AT+DADDR=A8 40 41 FF|Set the Application Session Key.|OK
366 366  
367 -(% style="display:none" %) (%%)
368 -
369 369  == 5.5 Device EUI ==
370 370  
371 -
372 372  Feature: Get or Set the Device EUI.
373 373  
285 +AT Command: AT+DEUI
374 374  
375 -(% style="color:blue" %)**AT Command: AT+DEUI**
376 -
377 -(% border="1" style="background-color:#f2f2f2; width:1035.22px" %)
378 -|(% style="background-color:#4f81bd; color:white; width:250px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:147px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:634px" %)**Response**
379 -|(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
287 +|=(% colspan="3" %)AT+DEUI
288 +|**Command Example**|**Function**|**Response**
289 +|AT+DEUI=?|Get the Device EUI.|00 44 34 22 33 45 55 55(((
380 380  OK
381 381  )))
382 -|(% style="width:250px" %)AT+DEUI=A8 40 41 FF FF 12 34 56|(% style="width:147px" %)Set the Device EUI.|(% style="width:634px" %)(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
292 +|AT+DEUI=A8 40 41 FF FF 12 34 56|Set the Device EUI.|(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((
383 383  OK
384 384  )))
385 385  
386 -(% style="display:none" %) (%%)
387 -
388 388  == 5.6 Network ID ==
389 389  
390 -
391 391  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
392 392  
300 +AT Command: AT+NWKID
393 393  
394 -(% style="color:blue" %)**AT Command: AT+NWKID**
395 -
396 -(% border="1" style="background-color:#f2f2f2; width:448.222px" %)
397 -|(% style="background-color:#4f81bd; color:white; width:191px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:153px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:101px" %)**Response**
398 -|(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
302 +|=(% colspan="3" %)AT+NWKID
303 +|**Command Example**|**Function**|**Response**
304 +|AT+NWKID=?|Get the Network ID.|a8 40 41 ff(((
399 399  OK
400 400  )))
401 -|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
307 +|AT+NWKID=A8 40 41 FF|Set the Network ID.|OK
402 402  
403 -(% style="display:none" %) (%%)
404 -
405 405  == 5.7 Network Session Key ==
406 406  
407 -
408 408  Feature: Get or Set the Network Session Key
409 409  
313 +AT Command: AT+NWKSKEY
410 410  
411 -(% style="color:blue" %)**AT Command: AT+NWKSKEY**
412 -
413 -(% border="1" style="background-color:#f2f2f2; width:1017.22px" %)
414 -|(% style="background-color:#4f81bd; color:white; width:455px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:215px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:343px" %)**Response**
415 -|(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
315 +|=(% colspan="3" %)AT+NWKSKEY
316 +|**Command Example**|**Function**|**Response**
317 +|AT+NWKSKEY=?|Get the Network Session Key.|00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
416 416  OK
417 417  )))
418 -|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
320 +|AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|Set the Network Session Key.|OK
419 419  
420 -(% style="display:none" %) (%%)
421 -
422 422  = 6. Joining and sending date on LoRaWAN network =
423 423  
424 424  == 6.1 Confirm Mode ==
425 425  
426 -=== 6.1.1  AT+CFM command before DR-LWS007 software stack ===
427 -
428 -
429 429  Feature: Get or Set the confirmation mode (0-1).
430 430  
328 +AT Command: AT+CFM
431 431  
432 -(% style="color:blue" %)**AT Command: AT+CFM**
433 -
434 -(% border="1" style="background-color:#f2f2f2; width:710.222px" %)
435 -|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:205px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:346px" %)**Response**
436 -|(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
330 +|=(% colspan="3" %)AT+CFM
331 +|**Command Example**|**Function**|**Response**
332 +|AT+CFM=?|Get the confirmation mode|0(((
437 437  OK
438 438  )))
439 -|(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
440 -|(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
335 +|AT+CFM=1|Set the confirmation mode|OK
336 +|AT+CFM=2|Set the confirmation mode|While Error in format, return AT_PARAM_ERROR
441 441  
442 -(% style="color:blue" %)**Downlink Command: 0x05**
338 +Downlink Command: 0x05
443 443  
444 444  Format: Command Code (0x05) followed by 2 bytes mode value.
445 445  
446 446  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
447 447  
448 -* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
449 -* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
344 +* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
345 +* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
450 450  
451 -(% style="display:none" %) (%%)
452 -
453 -=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
454 -
455 -
456 -(% style="color:blue" %)**AT Command: AT+CFM**
457 -
458 -(% border="1" style="background-color:#f2f2f2; width:710.222px" %)
459 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:198px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:349px" %)**Response**
460 -|(% style="width:160px" %)(((
461 -AT+CFM=1,0,0
462 -
463 -value1
464 -)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
465 -1
466 -
467 -OK
468 -)))
469 -|(% style="width:160px" %)(((
470 -AT+CFM=0,?,0
471 -
472 -value2
473 -)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
474 -0~~7
475 -
476 -OK
477 -)))
478 -|(% style="width:160px" %)(((
479 -AT+CFM=0,0,1
480 -
481 -value3
482 -)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
483 -1
484 -
485 -OK
486 -)))
487 -
488 -(% style="color:blue" %)**Downlink Command: 0x05**
489 -
490 -Format: Command Code (0x05) followed by 2 bytes mode value.
491 -
492 -If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
493 -
494 -* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
495 -* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
496 -
497 -(% style="display:none" %) (%%)
498 -
499 499  == 6.2 Confirm Status ==
500 500  
501 -
502 502  Feature: Get confirmation status of the last AT+SEND (0-1).
503 503  
351 +AT Command: AT+CFS
504 504  
505 -(% style="color:blue" %)**AT Command: AT+CFS**
506 -
507 -(% border="1" style="background-color:#f2f2f2; width:463px" %)
508 -|(% style="background-color:#4f81bd; color:white; width:156px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:193px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:107px" %)**Response**
509 -|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:107px" %)0(((
353 +|=(% colspan="3" %)AT+CFS
354 +|**Command Example**|**Function**|**Response**
355 +|AT+CFS=?|Get confirmation status|0(((
510 510  OK
511 511  )))
512 512  
513 -(% style="display:none" %) (%%)
514 -
515 515  == 6.3 Join LoRa® Network ==
516 516  
517 -
518 518  Feature: Join network.
519 519  
363 +AT Command: AT+JOIN
520 520  
521 -(% style="color:blue" %)**AT Command: AT+JOIN**
522 -
523 -(% border="1" style="background-color:#f2f2f2; width:647.222px" %)
524 -|(% style="background-color:#4f81bd; color:white; width:163px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:147px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:334px" %)**Response**
525 -|(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
365 +|=(% colspan="3" %)AT+JOIN
366 +|**Command Example**|**Function**|**Response**
367 +|AT+JOIN ?|Get imformation.|AT+JOIN: Join network(((
526 526  OK
369 +
527 527  While Error in format, return AT_BUSY_ERROR
528 528  )))
529 529  
530 -(% style="display:none" %) (%%)
531 -
532 532  == 6.4 LoRa® Network Join Mode ==
533 533  
534 -
535 535  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
536 536  
377 +AT Command: AT+NJM
537 537  
538 -(% style="color:blue" %)**AT Command: AT+NJM**
539 -
540 -(% border="1" style="background-color:#f2f2f2; width:753.222px" %)
541 -|(% style="background-color:#4f81bd; color:white; width:162px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:227px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:361px" %)**Response**
542 -|(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
379 +|=(% colspan="3" %)AT+NJM
380 +|**Command Example**|**Function**|**Response**
381 +|AT+NJM=?|Get the Network Join Mode|1(((
543 543  OK
544 544  )))
545 -|(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
546 -|(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
384 +|AT+NJM=0|Set the Network Join Mode|OK
385 +|AT+NJM=2|Set the Network Join Mode|While Error in format, return AT_PARAM_ERROR
547 547  
548 -(% style="color:blue" %)**Downlink Command: 0x20**
387 +Downlink Command: 0x20
549 549  
550 550  Format: Command Code (0x20) followed by 1 bytes mode value.
551 551  
552 552  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
553 553  
554 -* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
555 -* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
393 +* Example 1: Downlink Payload: 2000 ~/~/ Set AT+NJM=O
394 +* Example 2: Downlink Payload: 2001 ~/~/ Set AT+NJM=1
556 556  
557 -(% style="display:none" %) (%%)
558 -
559 559  == 6.5 LoRa® Network Join Status ==
560 560  
561 -
562 562  Feature: LoRa® Network Join Status.
563 563  
400 +AT Command: AT+NJS
564 564  
565 -(% style="color:blue" %)**AT Command: AT+NJS**
566 -
567 -(% border="1" style="background-color:#f2f2f2; width:498.222px" %)
568 -|(% style="background-color:#4f81bd; color:white; width:169px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:164px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:161px" %)**Response**
569 -|(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
402 +|=(% colspan="3" %)AT+NJS
403 +|**Command Example**|**Function**|**Response**
404 +|AT+NJS=?|Get the join status.|0(((
570 570  OK
571 571  )))
572 572  
573 -(% style="display:none" %) (%%)
574 -
575 575  == 6.6 Print Last Received Data in Raw Format ==
576 576  
577 -
578 578  Feature: Print Last Received Data in Raw Format<port:data>.
579 579  
412 +AT Command: AT+RECV
580 580  
581 -(% style="color:blue" %)**AT Command: AT+RECV**
582 -
583 -(% border="1" style="background-color:#f2f2f2; width:587.222px" %)
584 -|(% style="background-color:#4f81bd; color:white; width:161px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:272px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:150px" %)**Response**
585 -|(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
414 +|=(% colspan="3" %)AT+RECV
415 +|**Command Example**|**Function**|**Response**
416 +|AT+RECV=?|print last received data in raw format.|0:(((
586 586  OK
587 587  )))
588 588  
589 -(% style="display:none" %) (%%)
590 -
591 591  == 6.7 Print Last Received Data in Binary Format ==
592 592  
593 -
594 594  Feature: Print Last Received Data in Binary Format<port:data>.
595 595  
424 +AT Command: AT+RECVB
596 596  
597 -(% style="color:blue" %)**AT Command: AT+RECVB**
598 -
599 -(% border="1" style="background-color:#f2f2f2; width:793.222px" %)
600 -|(% style="background-color:#4f81bd; color:white; width:173px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:497px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:120px" %)**Response**
601 -|(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
426 +|=(% colspan="3" %)AT+RECVB
427 +|**Command Example**|**Function**|**Response**
428 +|AT+RECVB=?|print last received data in binary format (with hexadecimal values).|2: 0010(((
602 602  OK
603 603  )))
604 604  
605 -(% style="display:none" %) (%%)
606 -
607 607  == 6.8 Send Text Data ==
608 608  
609 -
610 610  Feature: Send Text Data<port:data>.
611 611  
436 +AT Command: AT+SEND
612 612  
613 -(% style="color:blue" %)**AT Command: AT+SEND**
614 -
615 -(% border="1" style="background-color:#f2f2f2; width:991.222px" %)
616 -|(% style="background-color:#4f81bd; color:white; width:201px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:340px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:446px" %)**Response**
617 -|(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
438 +|=(% colspan="3" %)AT+SEND
439 +|**Command Example**|**Function**|**Response**
440 +|AT+SEND=12:hello world|Send text data along with the application port.|OK(((
618 618  While Error in format, return
442 +
619 619  AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
444 +
445 +
620 620  )))
621 621  
622 -(% style="display:none" %) (%%)
623 -
624 624  == 6.9 Send Hexadecimal Data ==
625 625  
626 -
627 627  Feature: Send hexadecimal data along with the application port.
628 628  
452 +AT Command: AT+SENDB
629 629  
630 -(% style="color:blue" %)**AT Command: AT+SENDB**
454 +|=(% colspan="3" %)AT+SENDB
455 +|**Command Example**|**Function**|**Response**
456 +|AT+SENDB=12:abcdef0123456789|Send hexadecimal data along with the application port.|OK
457 +|AT+SENDB=abcdef0123456789|Send hexadecimal data along with the application port.|While Error in format, return(((
458 +AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
631 631  
632 -(% border="1" style="width:974px" %)
633 -|(% style="background-color:#4f81bd; color:white; width:257px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:394px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:318px" %)**Response**
634 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:318px" %)OK
635 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:318px" %)While Error in format, return(((
636 -AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
460 +
637 637  )))
638 638  
639 -(% style="display:none" %) (%%)
640 -
641 641  = 7. LoRaWAN network management =
642 642  
643 643  == 7.1 Adaptive Data Rate ==
644 644  
645 -
646 646  Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
647 647  
648 648  
649 -(% style="color:blue" %)**AT Command: AT+ADR**
470 +AT Command: AT+ADR
650 650  
651 -(% border="1" style="width:643px" %)
652 -|(% style="background-color:#4f81bd; color:white; width:162px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:266px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:209px" %)**Response**
653 -|(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:209px" %)1(((
472 +|=(% colspan="3" %)AT+ADR
473 +|**Command Example**|**Function**|**Response**
474 +|AT+ADR=?|Get the Adaptive Data Rate setting.|1(((
654 654  OK
655 655  )))
656 -|(% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:209px" %)OK
657 -|(% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:209px" %)While Error in format, return(((
477 +|AT+ADR=0|Set the Adaptive Data Rate setting.|OK
478 +|AT+ADR=2|Set the Adaptive Data Rate setting.|While Error in format, return(((
658 658  AT_PARAM_ERROR
659 659  )))
660 660  
661 -(% style="color:blue" %)**Downlink Command: 0x22**
482 +Downlink Command: 0x22
662 662  
484 +
663 663  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
664 664  
665 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
666 -* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
487 +* Example 1: Downlink Payload: 2201 ~/~/ Set AT+ADR=1.
488 +* Example 2: Downlink Payload: 2200FFFF ~/~/ Set AT+ADR=0.
667 667  
668 -(% style="display:none" %) (%%)
669 -
670 670  == 7.2 LoRa® Class ==
671 671  
672 -
673 673  Feature: Get or Set the Device Class(Currently only support class A, class C).
674 674  
494 +AT Command:AT+CLASS
675 675  
676 -(% style="color:blue" %)**AT Command:  AT+CLASS**
677 -
678 -(% border="1" style="background-color:#f2f2f2; width:507.222px" %)
679 -|(% style="background-color:#4f81bd; color:white; width:163px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:166px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:175px" %)**Response**
680 -|(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
496 +|=(% colspan="3" %)AT+CLASS
497 +|**Command Example**|**Function**|**Response**
498 +|AT+CLASS=?|Get the Device Class.|A(((
681 681  OK
682 682  )))
683 -|(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
501 +|AT+CLASS=C|Set the Device Class.|OK(((
684 684  
685 685  )))
686 686  
687 -(% style="display:none" %)
688 -
689 -(% style="color:red" %)**Notice:**
690 -
691 -* Run AT+FDR before running AT+CLASS=C
692 -* After change to Class=C, Before OTAA Join Successfule, the end node will still shows to use CLASS=A for OTAA Joined. It will use CLASS=C after OTAA Join Succeccful.
693 -
694 694  == 7.3 Duty Cycle Setting ==
695 695  
507 +Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
696 696  
697 -Feature: Get or Set the ETSI Duty Cycle setting** : 0**=disable, **1**=enable - Only for testing.
509 +AT Command:AT+DCS
698 698  
699 -
700 -(% style="color:blue" %)**AT Command:  AT+DCS**
701 -
702 -(% border="1" style="background-color:#f2f2f2; width:515.222px" %)
703 -|(% style="background-color:#4f81bd; color:white; width:165px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:239px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:107px" %)**Response**
704 -|(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
511 +|=(% colspan="3" %)AT+DCS
512 +|**Command Example**|**Function**|**Response**
513 +|AT+DCS=?|Get the ETSI Duty Cycle setting.|1(((
705 705  OK
706 706  )))
707 -|(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
516 +|AT+DCS=1|Set the ETSI Duty Cycle setting.|OK(((
708 708  
709 709  )))
710 710  
711 -(% style="display:none" %) (%%)
712 -
713 713  == 7.4 Data Rate ==
714 714  
522 +Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
715 715  
716 -Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) .
524 +AT Command: AT+DR
717 717  
718 -(% style="color:red" %)
719 -**Notice:**
720 -
721 -* User need to set Adaptive Data Rate(ADR)=0 first. otherwise device will respond to server's ADR command and change the DR according to server auto-adjustment.
722 -* Data Rate specifies Spreading Factor. The mapping varies in different frequency bands. User can check this link for detail. [[rp2-1.0.3-lorawan-regional-parameters.pdf>>https://lora-alliance.org/resource_hub/rp2-1-0-3-lorawan-regional-parameters/]]
723 -
724 -(% style="color:blue" %)**AT Command: AT+DR**
725 -
726 -(% border="1" style="background-color:#f2f2f2; width:466.222px" %)
727 -|(% style="background-color:#4f81bd; color:white; width:156px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:167px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:140px" %)**Response**
728 -|(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
526 +|=(% colspan="3" %)AT+DR
527 +|**Command Example**|**Function**|**Response**
528 +|AT+DR=?|Get the Data Rate.|5(((
729 729  OK
730 730  )))
731 -|(% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((
531 +|AT+DR=2|Set the Data Rate.|OK(((
732 732  
733 733  )))
734 734  
735 -(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
535 +Downlink Command: 0x2200aaFF
736 736  
537 +
737 737  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
738 738  
739 -* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
740 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
540 +* Example 1: Downlink Payload: 220001FF ~/~/ Set AT+DR=1.
541 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+DR=0.
741 741  
742 -(% style="display:none" %) (%%)
743 -
744 744  == 7.5 Frame Counter Downlink ==
745 745  
746 -
747 747  Feature: Get or Set the Frame Counter Downlink.
748 748  
547 +AT Command:AT+FCD
749 749  
750 -(% style="color:blue" %)**AT Command:  AT+FCD**
751 -
752 -(% border="1" style="background-color:#f2f2f2; width:693.222px" %)
753 -|(% style="background-color:#4f81bd; color:white; width:162px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:258px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:269px" %)**Response**
754 -|(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
549 +|=(% colspan="3" %)AT+FCD
550 +|**Command Example**|**Function**|**Response**
551 +|AT+FCD=?|Get the Frame Counter Downlink.|0(((
755 755  OK
756 756  )))
757 -|(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
554 +|AT+FCD=10|Set the Frame Counter Downlink.|(System will write new value to FCD)(((
758 758  OK
556 +
557 +
759 759  )))
760 760  
761 -(% style="display:none" %) (%%)
762 -
763 763  == 7.6 Frame Counter Uplink ==
764 764  
765 765  Feature: Get or Set the Frame Counter Uplink.
766 766  
564 +AT Command:AT+FCU
767 767  
768 -(% style="color:blue" %)**AT Command:  AT+FCU**
769 -
770 -(% border="1" style="background-color:#f2f2f2; width:534.222px" %)
771 -|(% style="background-color:#4f81bd; color:white; width:177px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:239px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:113px" %)**Response**
772 -|(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
566 +|=(% colspan="3" %)AT+FCU
567 +|**Command Example**|**Function**|**Response**
568 +|AT+FCU=?|Get the Frame Counter Uplink.|0(((
773 773  OK
774 774  )))
775 -|(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
571 +|AT+FCU=10|Set the Frame Counter Uplink.|OK(((
776 776  
777 777  )))
778 778  
779 -(% style="display:none" %) (%%)
780 -
781 781  == 7.7 Join Accept Delay1 ==
782 782  
783 -
784 784  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
785 785  
579 +AT Command:AT+JN1DL
786 786  
787 -(% style="color:blue" %)**AT Command:  AT+JN1DL**
788 -
789 -(% border="1" style="background-color:#f2f2f2; width:537.222px" %)
790 -|(% style="background-color:#4f81bd; color:white; width:164px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:229px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:140px" %)**Response**
791 -|(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
581 +|=(% colspan="3" %)AT+JN1DL
582 +|**Command Example**|**Function**|**Response**
583 +|AT+JN1DL=?|Get the Join Accept Delay.|5000(((
792 792  OK
793 793  )))
794 -|(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
586 +|AT+JN1DL=10000|Set the Join Accept Delay.|OK(((
795 795  
796 796  )))
797 797  
798 -(% style="display:none" %) (%%)
799 -
800 800  == 7.8 Join Accept Delay2 ==
801 801  
802 -
803 803  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
804 804  
594 +AT Command:AT+JN2DL
805 805  
806 -(% style="color:blue" %)**AT Command:  AT+JN2DL**
807 -
808 -(% border="1" style="background-color:#f2f2f2; width:538.222px" %)
809 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:228px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:146px" %)**Response**
810 -|(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
596 +|=(% colspan="3" %)AT+JN2DL
597 +|**Command Example**|**Function**|**Response**
598 +|AT+JN2DL=?|Get the Join Accept Delay.|6000(((
811 811  OK
812 812  )))
813 -|(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
601 +|AT+JN2DL=20000|Set the Join Accept Delay.|OK(((
814 814  
815 815  )))
816 816  
817 -(% style="display:none" %) (%%)
818 -
819 819  == 7.9 Public Network Mode ==
820 820  
607 +Feature: Get or Set the public network mode. (0: off, 1: on)
821 821  
822 -Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
609 +AT Command:AT+PNM
823 823  
824 -(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
825 -
826 -
827 -(% style="color:blue" %)**AT Command:  AT+PNM**
828 -
829 -(% border="1" style="background-color:#f2f2f2; width:667.222px" %)
830 -|(% style="background-color:#4f81bd; color:white; width:166px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:225px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:272px" %)**Response**
831 -|(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
611 +|=(% colspan="3" %)AT+PNM
612 +|**Command Example**|**Function**|**Response**
613 +|AT+PNM=?|Get the public network mode.|1(((
832 832  OK
833 833  )))
834 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
835 -Set the public network mode.
836 -
837 -Set syncword=0x34
838 -)))|(% style="width:272px" %)(System will write new value to PNM)(((
616 +|AT+PNM=1|Set the public network mode.|(System will write new value to PNM)(((
839 839  OK
840 840  
841 841  
842 842  )))
843 -|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
844 844  
845 -(% style="display:none" %) (%%)
846 -
847 847  == 7.10 Receive Delay1 ==
848 848  
849 -
850 850  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
851 851  
626 +AT Command:AT+RX1DL
852 852  
853 -(% style="color:blue" %)**AT Command: AT+RX1DL**
854 -
855 -(% border="1" style="background-color:#f2f2f2; width:408.222px" %)
856 -|(% style="background-color:#4f81bd; color:white; width:155px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:128px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:122px" %)**Response**
857 -|(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
628 +|=(% colspan="3" %)AT+RX1DL
629 +|**Command Example**|**Function**|**Response**
630 +|AT+RX1DL=?|Get the delay.|1000(((
858 858  OK
859 859  )))
860 -|(% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((
633 +|AT+RX1DL=1500|Set the delay.|OK(((
861 861  
862 862  )))
863 863  
864 -(% style="display:none" %) (%%)
637 +== 7.11Receive Delay2 ==
865 865  
866 -== 7.11 Receive Delay2 ==
867 -
868 -
869 869  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
870 870  
641 +AT Command:AT+RX2DL
871 871  
872 -(% style="color:blue" %)**AT Command: AT+RX2DL**
873 -
874 -(% border="1" style="background-color:#f2f2f2; width:481.222px" %)
875 -|(% style="background-color:#4f81bd; color:white; width:175px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:152px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:150px" %)**Response**
876 -|(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
643 +|=(% colspan="3" %)AT+RX2DL
644 +|**Command Example**|**Function**|**Response**
645 +|AT+RX2DL=?|Get the delay.|2000(((
877 877  OK
878 878  )))
879 -|(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
648 +|AT+RX2DL=2500|Set the delay.|OK(((
880 880  
881 881  )))
882 882  
883 -(% style="display:none" %) (%%)
884 -
885 885  == 7.12 Rx2 Window Data Rate ==
886 886  
887 -
888 888  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
889 889  
656 +AT Command:AT+RX2DR
890 890  
891 -(% style="color:blue" %)**AT Command:  AT+RX2DR**
892 -
893 -(% border="1" style="background-color:#f2f2f2; width:525.222px" %)
894 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:232px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:130px" %)**Response**
895 -|(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
658 +|=(% colspan="3" %)AT+RX2DR
659 +|**Command Example**|**Function**|**Response**
660 +|AT+RX2DR=?|Get the Rx2 window data rate.|2(((
896 896  OK
897 897  )))
898 -|(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
663 +|AT+RX2DR=6|Set the Rx2 window data rate.|OK(((
899 899  
900 900  )))
901 901  
902 -(% style="display:none" %) (%%)
903 -
904 904  == 7.13 Rx2 Window Frequency ==
905 905  
906 -
907 907  Feature: Get or Set the Rx2 window frequency
908 908  
671 +AT Command:AT+RX2FQ
909 909  
910 -(% style="color:blue" %)**AT Command:  AT+RX2FQ**
911 -
912 -(% border="1" style="background-color:#f2f2f2; width:587.222px" %)
913 -|(% style="background-color:#4f81bd; color:white; width:183px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:240px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:160px" %)**Response**
914 -|(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
673 +|=(% colspan="3" %)AT+RX2FQ
674 +|**Command Example**|**Function**|**Response**
675 +|AT+RX2FQ=?|Get the Rx2 window frequency.|434665000(((
915 915  OK
916 916  )))
917 -|(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
678 +|AT+RX2FQ=434665000|Set the Rx2 window frequency.|OK(((
918 918  
919 919  )))
920 920  
921 -(% style="display:none" %) (%%)
922 -
923 923  == 7.14 Transmit Power ==
924 924  
925 -
926 926  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
927 927  
928 -(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
686 +AT Command:AT+TXP
929 929  
930 -
931 -(% style="color:blue" %)**AT Command:  AT+TXP**
932 -
933 -(% border="1" style="background-color:#f2f2f2; width:465.222px" %)
934 -|(% style="background-color:#4f81bd; color:white; width:161px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:189px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:112px" %)**Response**
935 -|(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
688 +|=(% colspan="3" %)AT+TXP
689 +|**Command Example**|**Function**|**Response**
690 +|AT+TXP=?|Get the Transmit Power.|0(((
936 936  OK
937 937  )))
938 -|(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
693 +|AT+TXP=1|Set the Transmit Power.|OK(((
939 939  
940 940  )))
941 941  
... ... @@ -943,376 +943,195 @@
943 943  
944 944  If the downlink payload=22000100, it means setting the TXP to 0.
945 945  
946 -* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
947 -* **Example 2**: Downlink Payload: **22000000**  ~/~/ Set AT+TXP=0.
701 +* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2.
702 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0.
948 948  
949 -(% style="display:none" %) (%%)
950 -
951 951  == 7.15 RSSI of the Last Received Packet ==
952 952  
953 -
954 954  Feature: Get or Set the Rx2 window frequency
955 955  
708 +AT Command:AT+RSSI
956 956  
957 -(% style="color:blue" %)**AT Command:AT+RSSI**
958 -
959 -(% border="1" style="background-color:#f2f2f2; width:557.222px" %)
960 -|(% style="background-color:#4f81bd; color:white; width:164px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:289px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:100px" %)**Response**
961 -|(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
710 +|=(% colspan="3" %)AT+RSSI
711 +|**Command Example**|**Function**|**Response**
712 +|AT+RSSI=?|Get the RSSI of the last received packet.|0(((
962 962  OK
963 963  )))
964 964  
965 -(% style="display:none" %) (%%)
966 -
967 967  == 7.16 SNR of the Last Received Packet ==
968 968  
969 -
970 970  Feature: Get the SNR of the last received packet
971 971  
720 +AT Command:AT+SNR
972 972  
973 -(% style="color:blue" %)**AT Command:  AT+SNR**
974 -
975 -(% border="1" style="background-color:#f2f2f2; width:571.222px" %)
976 -|(% style="background-color:#4f81bd; color:white; width:164px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:290px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:113px" %)**Response**
977 -|(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
722 +|=(% colspan="3" %)AT+SNR
723 +|**Command Example**|**Function**|**Response**
724 +|AT+SNR=?|Get the RSSI of the last received packet.|0(((
978 978  OK
979 979  )))
980 980  
981 -(% style="display:none" %) (%%)
982 -
983 983  == 7.17 Application Port ==
984 984  
985 -
986 986  Feature: Get or set the application port.
987 987  
732 +AT Command: AT+PORT
988 988  
989 -(% style="color:blue" %)**AT Command: AT+PORT**
990 -
991 -(% border="1" style="background-color:#f2f2f2; width:500.222px" %)
992 -|(% style="background-color:#4f81bd; color:white; width:157px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:204px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:135px" %)**Response**
993 -|(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
734 +|=(% colspan="3" %)AT+PORT
735 +|**Command Example**|**Function**|**Response**
736 +|AT+PORT=?|Get the application port|21(((
994 994  OK
995 995  )))
996 -|(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
739 +|AT+PORT=21|Set the application port|OK
997 997  
998 -(% style="color:blue" %)**Downlink Command: 0x23**
741 +Downlink Command: 0x23
999 999  
1000 1000  Format: Command Code (0x23) followed by 1 bytes port value.
1001 1001  
1002 1002  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1003 1003  
1004 -* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1005 -* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
747 +* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1
748 +* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5
1006 1006  
1007 -(% style="display:none" %) (%%)
1008 -
1009 1009  == 7.18 Single Channel Mode ==
1010 1010  
1011 -
1012 1012  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
1013 1013  
754 +AT Command: AT+CHS
1014 1014  
1015 -(% style="color:blue" %)**AT Command: AT+CHS**
1016 -
1017 -(% border="1" style="background-color:#f2f2f2; width:603.222px" %)
1018 -|(% style="background-color:#4f81bd; color:white; width:182px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:295px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:122px" %)**Response**
1019 -|(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
756 +|=(% colspan="3" %)AT+CHS
757 +|**Command Example**|**Function**|**Response**
758 +|AT+CHS=?|Get Frequency for Single Channel Mode|0(((
1020 1020  OK
1021 1021  )))
1022 -|(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
761 +|AT+CHS=868100000|Set Frequency for Single Channel Mode|OK
1023 1023  
1024 -(% style="display:none" %) (%%)
1025 -
1026 1026  == 7.19 Eight Channel Mode ==
1027 1027  
1028 -
1029 1029  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1030 1030  
767 +AT Command: AT+CHE
1031 1031  
1032 -(% style="color:blue" %)**AT Command: AT+CHE**
1033 -
1034 -(% border="1" style="background-color:#f2f2f2; width:710.222px" %)
1035 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:198px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:349px" %)**Response**
1036 -|(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
769 +|=(% colspan="3" %)AT+CHE
770 +|**Command Example**|**Function**|**Response**
771 +|AT+CHE=?|Get eight channels mode|1(((
1037 1037  902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
1038 1038  
1039 1039  OK
1040 1040  )))
1041 -|(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
776 +|AT+CHE=1|Set eight channels mode|OK
1042 1042  
1043 -(% style="color:blue" %)**Downlink Command: 0x24 (LHT65,LHT65N Downlink Command:0x07)**
778 +Downlink Command: 0x24
1044 1044  
1045 1045  Format: Command Code (0x24) followed by 1 bytes channel value.
1046 1046  
1047 1047  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1048 1048  
1049 -* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1050 -* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
784 +* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1
785 +* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5
1051 1051  
1052 -(% style="display:none" %) (%%)
1053 -
1054 1054  == 7.20 Get or Set RXwindows1 timeout ==
1055 1055  
789 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1056 1056  
1057 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
791 +AT Command: AT+RX1WTO
1058 1058  
1059 -
1060 -(% style="color:blue" %)**AT Command: AT+RX1WTO**
1061 -
1062 -(% border="1" style="background-color:#f2f2f2; width:460.222px" %)
1063 -|(% style="background-color:#4f81bd; color:white; width:163px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:201px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:93px" %)**Response**
1064 -|(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
793 +|=(% colspan="3" %)AT+ RX1WTO
794 +|**Command Example**|**Function**|**Response**
795 +|AT+RX1WTO=?|Get RXwindows1 timeout|14(((
1065 1065  OK
1066 1066  )))
1067 -|(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
798 +|AT+RX1WTO=60|Set RXwindows1 timeout|OK
1068 1068  
1069 -(% style="display:none" %) (%%)
800 +AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1070 1070  
1071 -(((
1072 -(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1073 -)))
802 +[[~[~[image:https://wiki.dragino.com/images/thumb/5/51/RX1WTO.JPG/600px-RX1WTO.JPG~|~|alt="RX1WTO.JPG" height="239" width="600"~]~]>>url:https://wiki.dragino.com/index.php/File:RX1WTO.JPG]]
1074 1074  
1075 -[[image:image-20220526162535-1.png]]
1076 -
1077 -(((
1078 1078  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1079 -)))
1080 1080  
1081 -
1082 1082  == 7.21 Get or Set RXwindows2 timeout ==
1083 1083  
808 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1084 1084  
1085 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
810 +AT Command: AT+RX2WTO
1086 1086  
1087 -
1088 -(% style="color:blue" %)**AT Command: AT+RX2WTO**
1089 -
1090 -(% border="1" style="background-color:#f2f2f2; width:497.222px" %)
1091 -|(% style="background-color:#4f81bd; color:white; width:190px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:199px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:104px" %)**Response**
1092 -|(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
812 +|=(% colspan="3" %)AT+ RX2WTO
813 +|**Command Example**|**Function**|**Response**
814 +|AT+RX2WTO=?|Get RXwindows2 timeout|7(((
1093 1093  OK
1094 1094  )))
1095 -|(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
817 +|AT+RX2WTO=20|Set RXwindows2 timeout|OK
1096 1096  
1097 -(% style="display:none" %) (%%)
1098 -
1099 1099  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1100 1100  
1101 -
1102 1102  Feature: Get or Set uplinkdwelltime
1103 1103  
823 +AT Command: AT+DWELLT
1104 1104  
1105 -(% style="color:blue" %)**AT Command: AT+DWELLT**
1106 -
1107 -(% border="1" style="background-color:#f2f2f2; width:497.222px" %)
1108 -|(% style="background-color:#4f81bd; color:white; width:183px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:179px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:131px" %)**Response**
1109 -|(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
825 +|=(% colspan="3" %)AT+DWELLT
826 +|**Command Example**|**Function**|**Response**
827 +|AT+DWELLT=?|Get uplinkdwelltime|1(((
1110 1110  OK
1111 1111  )))
1112 -|(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
830 +|AT+DWELLT=0|Set uplinkdwelltime|OK
1113 1113  
1114 -(% style="color:blue" %)**Downlink Command: 0x25**
832 +Downlink Command: 0x25
1115 1115  
1116 1116  Format: Command Code (0x25) followed by 1 bytes state value.
1117 1117  
1118 1118  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1119 1119  
1120 -* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1121 -* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
838 +* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1
839 +* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0
1122 1122  
1123 -(% style="display:none" %) (%%)
1124 -
1125 1125  == 7.23 Set Packet Receiving Response Level ==
1126 1126  
1127 -
1128 1128  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1129 1129  
845 +RPL value:
1130 1130  
1131 -(% style="color:blue" %)**RPL value:**
847 +* AT+RPL=0: Device won't immediately reply any downlink commands from platform.
848 +* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
849 +* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
850 +* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
851 +* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1132 1132  
1133 -* **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1134 -* **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1135 -* **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1136 -* **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1137 -* **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
853 +Case Analyes:
1138 1138  
1139 -(% style="color:blue" %)**Case Analyes:**
1140 -
1141 1141  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1142 1142  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1143 1143  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1144 1144  
1145 -(% style="color:blue" %)**AT Command: AT+RPL**
859 +AT Command: AT+RPL
1146 1146  
1147 -(% border="1" style="background-color:#f2f2f2; width:536.222px" %)
1148 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:263px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:109px" %)**Response**
1149 -|(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
861 +|=(% colspan="3" %)AT+RPL
862 +|**Command Example**|**Function**|**Response**
863 +|AT+RPL=?|Get packet receiving response level|1(((
1150 1150  OK
1151 1151  )))
1152 -|(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
866 +|AT+RPL=0|Set packet receiving response level|OK
1153 1153  
1154 -(% style="color:blue" %)**Downlink Command: 0x21**
868 +Downlink Command: 0x21
1155 1155  
1156 1156  Format: Command Code (0x21) followed by 1 bytes level value.
1157 1157  
1158 1158  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1159 1159  
1160 -* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1161 -* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
874 +* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1
875 +* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2
1162 1162  
1163 -(% style="display:none" %) (%%)
1164 -
1165 -== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1166 -
1167 -
1168 -(% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1169 -
1170 -(% border="1" style="background-color:#f2f2f2; width:589px" %)
1171 -|(% style="background-color:#4f81bd; color:white; width:227px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:300px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:87px" %)**Response**
1172 -|(% style="width:227px" %)AT+SETMAXNBTRANS=1，0|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1173 -OK
1174 -)))
1175 -|(% style="width:227px" %)AT+SETMAXNBTRANS=？，1|(% style="width:300px" %)(((
1176 -value2: 0: uplink fcnt doesn't change for each NBTrans;
1177 -
1178 -1: uplink fcnt increase by 1 for each NBTrans.
1179 -)))|(% style="width:87px" %)(((
1180 -1
1181 -
1182 -OK
1183 -)))
1184 -
1185 -(% style="color:blue" %)**Downlink Command: 0x33**
1186 -
1187 -Format: Command Code (0x33) followed by 2 bytes mode value.
1188 -
1189 -If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1190 -
1191 -* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1192 -* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1193 -
1194 -(% style="display:none" %) (%%)
1195 -
1196 -== 7.25 Device offline rejoining （LWS007) ==
1197 -
1198 -
1199 -(% style="color:blue" %)**AT Command: AT+DDETECT**
1200 -
1201 -AT+DDETECT=<Flag>,<ACK_Timout_1>,<ACK_Timout_2> (Default Value: AT+DDETECT=1,1440,2880)
1202 -
1203 -* ACK_Timout_1: Unit: min
1204 -* ACK_Timout_2: Unit: min
1205 -
1206 -(% border="1" style="background-color:#f2f2f2; width:710.222px" %)
1207 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:198px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:349px" %)**Response**
1208 -|(% style="width:160px" %)(((
1209 -AT+DDETECT=1,1440,2880
1210 -
1211 -value1
1212 -)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1213 -1
1214 -
1215 -OK
1216 -)))
1217 -|(% style="width:160px" %)(((
1218 -AT+DDETECT=1,?,2880
1219 -
1220 -value2
1221 -)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1222 -
1223 -
1224 -OK
1225 -)))
1226 -|(% style="width:160px" %)(((
1227 -AT+DDETECT=1,1440,？
1228 -
1229 -value3
1230 -)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1231 -
1232 -
1233 -OK
1234 -)))
1235 -
1236 -(% style="color:blue" %)**Downlink Command: 0x32**
1237 -
1238 -Format: Command Code (0x32) followed by 2 bytes mode value.
1239 -
1240 -If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 32.
1241 -
1242 -* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1243 -** 0x01 : Flag
1244 -** 0x05A0: ACK_Timout_1 : 1440minutes (24 hours)
1245 -** 0x0B40: ACK_Timout_2 : 2880minutes (48 hours)
1246 -** **Explain**: Enable Online Detect, if end node doesn't receive any downlink within ACK_Timout_1( 1440 minutes or 24 hours). End node will use confirmed uplink to send packets during ACK_Timout_1 (the 24th hour) to ACK_Timout_2 ( the 48th hour). If from the 24th to 48th hour, end node got an downlink from server, it will switch back to unconfirmed uplink. end node will restart ACK_Timout_1. If from the 24th to 48th hour, end node still not got any downlink, means device doesn't get ACK from server within last 48 hours. Device will process rejoin, rejoin request interval is AT+RJTDC period. For AU915/ US915, device will use the sub-band used for last join.
1247 -
1248 -(% style="display:none" %) (%%)
1249 -
1250 -== 7.26 Request the server to send an ACK ==
1251 -
1252 -
1253 -(% style="color:blue" %)**AT Command: AT+PNACKMD**
1254 -
1255 -(% border="1" style="background-color:#f2f2f2; width:536.222px" %)
1256 -|(% style="background-color:#4f81bd; color:white; width:160px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:263px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:109px" %)**Response**
1257 -|(% style="width:160px" %)AT+PNACKMD=1|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1258 -OK
1259 -)))
1260 -|(% style="width:160px" %)AT+PNACKMD=0|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1261 -0
1262 -OK
1263 -)))
1264 -
1265 -(% style="display:none" %) (%%)
1266 -
1267 -== 7.27 Adjust network rejoining interval ==
1268 -
1269 -
1270 -(% style="color:blue" %)**AT Command: AT+RJTDC**
1271 -
1272 -(% border="1" style="background-color:#f2f2f2; width:727.222px" %)
1273 -|(% style="background-color:#4f81bd; color:white; width:165px" %)**Command Example**|(% style="background-color:#4f81bd; color:white; width:227px" %)**Function**|(% style="background-color:#4f81bd; color:white; width:329px" %)**Response**
1274 -|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30(((
1275 -OK
1276 -
1277 -the interval is 30 min
1278 -)))
1279 -|(% style="width:165px" %)AT+RJTDC=60|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1280 -Set the ReJoin data transmission interval to 60 min
1281 -)))
1282 -
1283 -(% style="color:blue" %)**Downlink Command: 0x26**
1284 -
1285 -Format: Command Code (0x26) followed by 2 bytes mode value.
1286 -
1287 -If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1288 -
1289 -* **Example 1:** Downlink Payload: 26000A  ~/~/  Set AT+RJTDC=10
1290 -* **Example 2: **Downlink Payload: 260002  ~/~/  Set AT+RJTDC=2
1291 -
1292 -(% style="display:none" %) (%%)
1293 -
1294 1294  = 8. AT Commands Combination =
1295 1295  
1296 1296  == 8.1 Set a fix RX2DR for downlink window ==
1297 1297  
881 +* AT+ADR=0 ~-~-> Disable ADR first
882 +* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate
1298 1298  
1299 -* (% style="color:blue" %)**AT+ADR=0             **(%%) **~/~/**  Disable ADR first
1300 -
1301 -* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~/~/**  Set xxxx to your wanted DataRate
1302 -
1303 -(% style="display:none" %) (%%)
1304 -
1305 1305  == 8.2 Use Downlink Command to set a fix uplink DR ==
1306 1306  
886 +Downlink Command: 0x22000500
1307 1307  
1308 -(% style="color:blue" %)**Downlink Command: 0x22000500**
888 +Same as:
1309 1309  
1310 -**Same as:**
1311 -
1312 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1313 -
1314 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1315 -
1316 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1317 -
1318 -
890 +* AT+ADR=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Adaptive_Data_Rate]]
891 +* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]]
892 +* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]
image-20220511120050-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -136.3 KB
Content
image-20220526162535-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -149.4 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0