Last modified by kai on 2024/09/06 10:00
<
From version < 63.1 >
edited by Edwin Chen
on 2023/04/05 11:31
To version < 7.7 >
edited by Xiaoling
on 2022/05/11 10:45
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Xiaoling
Content
... ... @@ -1,120 +1,55 @@
1 - **Table of** **Contents：**
1 +Contens
2 2  
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 -
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 -* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
10 +* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
11 +* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 -(((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 -)))
14 +
18 18  
19 -
20 20  = 2. How to use AT Commands or Downlink command =
21 21  
18 +* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
19 +* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
20 +** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
21 +** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
22 +** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
22 22  
23 -* **AT Command** : See Devices User Manual for how to connect to device via USB TTL adapter and use. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
24 -* **LoRaWAN Downlink Command**: The gateway transfer downlink command in HEX format. This page shows the Downlink Command In HEX format. Please note some LoRaWAN servers use base64 as downlink code so user need to convert HEX to Base64 and use. Below are references for how to use downlink command:
25 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
26 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]], [[How to Convert>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.1ConvertHEXtoBase64]]?
27 -** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
28 -
29 -(% style="display:none" %) (%%)
30 -
31 31  = 3. Support End Node and firmware version =
32 32  
33 -
34 -(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
35 -|=(% colspan="3" style="width: 963px;" %)(((
36 -Dragino STM32 base hardware Firmware / LoRaWAN stack list
37 -)))
38 -|(% style="width:187px" %)(((
39 -**Model**
40 -)))|(% style="width:330px" %)(((
41 -**Description**
42 -)))|(% style="width:445px" %)(((
43 -**Firmware Version <~-~-> Stack Version**
44 -)))
45 -|(% style="width:187px" %)(((
46 -[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
47 -)))|(% style="width:330px" %)(((
48 -Open Source Generic LoRaWAN Sensor Node
49 -)))|(% style="width:445px" %)(((
50 -(((
51 -LSN50 v1.6.0 <~-~-> DR-LWS-003;
52 -)))
53 -
54 -(((
55 -(((
26 +(% style="background-color:#ffffcc; color:green; width:995.222px" %)
27 +|=(% colspan="3" style="width: 992px;" %)Dragino STM32 base hardware Firmware / LoRaWAN stack list
28 +|(% style="width:187px" %)**Model**|(% style="width:349px" %)**Description**|(% style="width:453px" %)**Firmware Version <~-~-> Stack Version**
29 +|(% style="width:187px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:349px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:453px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;(((
56 56  LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
57 57  )))
58 -)))
59 -)))
60 -|(% style="width:187px" %)(((
61 -[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
62 -)))|(% style="width:330px" %)(((
63 -LoRaWAN GPS Tracker
64 -)))|(% style="width:445px" %)(((
65 -(((
66 -LGT92 v1.6.3 <~-~-> DR-LWS-003;
67 -)))
68 -
69 -(((
70 -(((
32 +|(% style="width:187px" %)[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],|(% style="width:349px" %)LoRaWAN GPS Tracker|(% style="width:453px" %)LGT92 v1.6.3 <~-~-> DR-LWS-003;(((
71 71  LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
72 72  )))
73 -)))
74 -)))
75 -|(% style="width:187px" %)(((
76 -[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
77 -)))|(% style="width:330px" %)(((
78 -LoRaWAN BLE Indoor Tracker
79 -)))|(% style="width:445px" %)(((
80 -LBT1 v1.0 <~-~-> DR-LWS-005;
81 -)))
82 -|(% style="width:187px" %)(((
83 -[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
84 -)))|(% style="width:330px" %)(((
85 -LoRaWAN RS485 Modbus Converter
86 -)))|(% style="width:445px" %)(((
87 -RS485-LN v1.3 <~-~-> DR-LWS-005;
88 -)))
89 -|(% style="width:187px" %)(((
90 -[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
91 -)))|(% style="width:330px" %)(((
92 -LoRaWAN Temperature & Humidity Sensor
93 -)))|(% style="width:445px" %)(((
94 -(((
95 -LHT65 v1.7 <~-~-> DR-LWS-003;
96 -)))
97 -
98 -(((
99 -(((
35 +|(% style="width:187px" %)[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],|(% style="width:349px" %)LoRaWAN BLE Indoor Tracker|(% style="width:453px" %)LBT1 v1.0 <~-~-> DR-LWS-005;
36 +|(% style="width:187px" %)[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],|(% style="width:349px" %)LoRaWAN RS485 Modbus Converter|(% style="width:453px" %)RS485-LN v1.3 <~-~-> DR-LWS-005;
37 +|(% style="width:187px" %)[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],|(% style="width:349px" %)LoRaWAN Temperature & Humidity Sensor|(% style="width:453px" %)LHT65 v1.7 <~-~-> DR-LWS-003;(((
100 100  LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
101 101  )))
102 -)))
103 -)))
104 104  
105 -(% style="display:none" %) (%%)
106 -
107 107  = 4. System Management Commands =
108 108  
109 109  == 4.1 Change Uplink Interval ==
110 110  
111 -
112 112  Feature: Change LoRaWAN End Node Transmit Interval.
113 113  
47 +(% class="box infomessage" %)
48 +(((
49 +**AT Command: AT+TDC**
50 +)))
114 114  
115 -(% style="color:blue" %)**AT Command: AT+TDC**
116 -
117 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
52 +(% style="background-color:#ffffcc; color:green; width:727.222px" %)
118 118  |=(% colspan="3" style="width: 724px;" %)AT+TDC
119 119  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
120 120  |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
... ... @@ -126,35 +126,29 @@
126 126  Set transmit interval to 60000ms = 60 seconds
127 127  )))
128 128  
129 -(((
130 -
64 +{{info}}
65 +**Downlink Command: 0x01**
66 +{{/info}}
131 131  
132 -(% style="color:blue" %)**Downlink Command: 0x01**
133 -
134 134  Format: Command Code (0x01) followed by 3 bytes time value.
135 -)))
136 136  
137 -(((
138 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
139 -)))
70 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
140 140  
141 -* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
142 -* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
72 +* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
73 +* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
143 143  
144 -(% style="display:none" %) (%%)
145 -
146 146  == 4.2 Reboot End Node ==
147 147  
148 -
149 149  Feature: Reboot End Node to perform a new OTAA or ABP Join.
150 150  
79 +{{info}}
80 +**AT Command: ATZ**
81 +{{/info}}
151 151  
152 -(% style="color:blue" %)**AT Command: ATZ**
153 -
154 -(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
155 -|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
156 -|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
157 -|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
83 +(% border="0" style="background-color:#ffffcc; color:green; width:727.222px" %)
84 +|=(% colspan="3" %)ATZ: Trig a reset of the MCU
85 +|**Command Example**|**Function**|**Response**
86 +|ATZ|Reset MCU|(((
158 158  Device reset and show booting info
159 159  
160 160  LSN50 Device/LoRa ST Module
... ... @@ -168,29 +168,26 @@
168 168  <followed by the Tx and Rx information>
169 169  )))
170 170  
171 -(% style="color:blue" %)**Downlink Command: 0x04**
100 +{{info}}
101 +**Downlink Command: 0x04**
102 +{{/info}}
172 172  
173 -(((
174 174  Format: Command Code (0x04) followed by FF.
175 -)))
176 176  
177 -(((
178 -If the downlink payload=**04FF**, the end node will reboot.
179 -)))
106 +If the downlink payload=**04FF**, the end node will reboot.
180 180  
181 -
182 182  == 4.3 Reset to factory Default ==
183 183  
184 -
185 185  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
186 186  
112 +{{info}}
113 +**AT Command: AT+FDR**
114 +{{/info}}
187 187  
188 -(% style="color:blue" %)**AT Command: AT+FDR**
189 -
190 -(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
191 -|=(% colspan="3" style="width: 786px;" %)Reset to factory default
192 -|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
193 -|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
116 +(% style="background-color:#ffffcc; color:green; width:831.222px" %)
117 +|=(% colspan="3" style="width: 828px;" %)Reset to factory default
118 +|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
119 +|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
194 194  Device reset to factory default parameters and show booting info
195 195  
196 196  LSN50 Device/LoRa ST Module
... ... @@ -204,59 +204,47 @@
204 204  Please set the parameters or reset Device to apply change
205 205  )))
206 206  
207 -(% style="color:blue" %)**Downlink Command: 0x04**
133 +{{info}}
134 +**Downlink Command: 0x04**
135 +{{/info}}
208 208  
209 -(((
210 210  Format: Command Code (0x04) followed by FE.
211 -)))
212 212  
213 -(((
214 214  If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
215 -)))
216 216  
217 217  
218 218  == 4.4 Show Firmware Version ==
219 219  
220 -
221 221  Feature: Show firmware version. No downlink command yet.
222 222  
146 +{{info}}
147 +**AT Command: AT+VER**
148 +{{/info}}
223 223  
224 -(% style="color:blue" %)**AT Command: AT+VER**
225 -
226 -(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
227 -|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
228 -|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
229 -|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
150 +(% style="background-color:#ffffcc; color:green" %)
151 +|=(% colspan="3" %)AT+VER: Image Version and Frequency Band
152 +|**Command Example**|**Function**|**Response**
153 +|AT+VER=?|Show Image version and Frequency Band|(((
230 230  1.3 EU868
231 231  
232 232  OK
233 233  )))
234 234  
235 -(% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
159 +{{info}}
160 +**Downlink Command: 0x26 (Valid in 006 stack)**
161 +{{/info}}
236 236  
237 -(((
238 238  Downlink Format: 0x26
239 -)))
240 240  
241 -(((
242 242  Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
243 -)))
244 244  
245 -(((
246 -
247 -
248 248  **xx: Software Type:**
249 -)))
250 250  
251 251  * 0x00 01: LGT92 Version
252 252  * 0x00 02: LBT1
253 253  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
254 254  
255 -(((
256 -
257 -
258 258  **yy: Frequency Band:**
259 -)))
260 260  
261 261  * 0x01: EU868
262 262  * 0x02: US915
... ... @@ -269,11 +269,7 @@
269 269  * 0x09: AS923-2
270 270  * 0xa0: AS923-3
271 271  
272 -(((
273 -
274 -
275 275  **zz: Subband**
276 -)))
277 277  
278 278  firmware version: v1.1.0 ~-~-> 110
279 279  
... ... @@ -280,37 +280,41 @@
280 280  
281 281  == 4.5 Show System Configure ==
282 282  
283 -
284 284  Feature: Show All configure. No downlink command yet.
285 285  
195 +{{info}}
196 +**AT Command: AT+CFG**
197 +{{/info}}
286 286  
287 -(% style="color:blue" %)**AT Command: AT+CFG**
288 -
289 -(% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
199 +(% style="background-color:#ffffcc; color:green; width:599.222px" %)
290 290  |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
291 291  |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
292 292  |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
293 293  AT+DEUI = XX XX XX XX XX XX XX XX
204 +
294 294  AT+DADDR=XXXXXXXX
206 +
295 295  ……….
208 +
296 296  AT+RX2WTO=X
210 +
297 297  AT+CHS=868100000
212 +
298 298  OK
299 299  )))
300 300  
301 -(% style="display:none" %) (%%)
302 302  
303 303  = 5. Keys, IDs and EUIs management =
304 304  
305 305  == 5.1 Application EUI ==
306 306  
307 -
308 308  Feature: Get or Set the Application EUI.
309 309  
223 +{{info}}
224 +**AT Command: AT+APPEUI**
225 +{{/info}}
310 310  
311 -(% style="color:blue" %)**AT Command: AT+APPEUI**
312 -
313 -(% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
227 +(% style="background-color:#ffffcc; color:green; width:686.222px" %)
314 314  |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
315 315  |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
316 316  |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
... ... @@ -318,17 +318,15 @@
318 318  )))
319 319  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
320 320  
321 -(% style="display:none" %) (%%)
322 -
323 323  == 5.2 Application Key ==
324 324  
325 -
326 326  Feature: Get or Set the Application Key.
327 327  
239 +{{info}}
240 +**AT Command: AT+APPKEY**
241 +{{/info}}
328 328  
329 -(% style="color:blue" %)**AT Command: AT+APPKEY**
330 -
331 -(% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
243 +(% style="background-color:#ffffcc; color:green; width:976.222px" %)
332 332  |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
333 333  |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
334 334  |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
... ... @@ -336,17 +336,15 @@
336 336  )))
337 337  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
338 338  
339 -(% style="display:none" %) (%%)
340 -
341 341  == 5.3 Application Session Key ==
342 342  
343 -
344 344  Feature: Get or Set the Application Session Key.
345 345  
255 +{{info}}
256 +**AT Command: AT+APPSKEY**
257 +{{/info}}
346 346  
347 -(% style="color:blue" %)**AT Command: AT+APPSKEY**
348 -
349 -(% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
259 +(% style="background-color:#ffffcc; color:green; width:1040.22px" %)
350 350  |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
351 351  |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
352 352  |(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
... ... @@ -356,17 +356,15 @@
356 356  OK
357 357  )))
358 358  
359 -(% style="display:none" %) (%%)
360 -
361 361  == 5.4 Device Address ==
362 362  
363 -
364 364  Feature: Get or Set the Device Address.
365 365  
273 +{{info}}
274 +**AT Command: AT+DADDR**
275 +{{/info}}
366 366  
367 -(% style="color:blue" %)**AT Command: AT+DADDR**
368 -
369 -(% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
277 +(% style="background-color:#ffffcc; color:green; width:795.222px" %)
370 370  |=(% colspan="3" style="width: 792px;" %)AT+DADDR
371 371  |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
372 372  |(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
... ... @@ -376,17 +376,15 @@
376 376  )))
377 377  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
378 378  
379 -(% style="display:none" %) (%%)
380 -
381 381  == 5.5 Device EUI ==
382 382  
383 -
384 384  Feature: Get or Set the Device EUI.
385 385  
291 +{{info}}
292 +**AT Command: AT+DEUI**
293 +{{/info}}
386 386  
387 -(% style="color:blue" %)**AT Command: AT+DEUI**
388 -
389 -(% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
295 +(% style="background-color:#ffffcc; color:green; width:1035.22px" %)
390 390  |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
391 391  |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
392 392  |(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
... ... @@ -396,17 +396,15 @@
396 396  OK
397 397  )))
398 398  
399 -(% style="display:none" %) (%%)
400 -
401 401  == 5.6 Network ID ==
402 402  
403 -
404 404  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
405 405  
309 +{{info}}
310 +**AT Command: AT+NWKID**
311 +{{/info}}
406 406  
407 -(% style="color:blue" %)**AT Command: AT+NWKID**
408 -
409 -(% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
313 +(% style="background-color:#ffffcc; color:green; width:448.222px" %)
410 410  |=(% colspan="3" style="width: 445px;" %)AT+NWKID
411 411  |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
412 412  |(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
... ... @@ -414,17 +414,15 @@
414 414  )))
415 415  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
416 416  
417 -(% style="display:none" %) (%%)
418 -
419 419  == 5.7 Network Session Key ==
420 420  
421 -
422 422  Feature: Get or Set the Network Session Key
423 423  
325 +{{info}}
326 +**AT Command: AT+NWKSKEY**
327 +{{/info}}
424 424  
425 -(% style="color:blue" %)**AT Command: AT+NWKSKEY**
426 -
427 -(% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
329 +(% style="background-color:#ffffcc; color:green; width:1017.22px" %)
428 428  |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
429 429  |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
430 430  |(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
... ... @@ -432,21 +432,17 @@
432 432  )))
433 433  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
434 434  
435 -(% style="display:none" %) (%%)
436 -
437 437  = 6. Joining and sending date on LoRaWAN network =
438 438  
439 439  == 6.1 Confirm Mode ==
440 440  
441 -=== 6.1.1  AT+CFM command before DR-LWS007 software stack ===
442 -
443 -
444 444  Feature: Get or Set the confirmation mode (0-1).
445 445  
343 +{{info}}
344 +**AT Command: AT+CFM**
345 +{{/info}}
446 446  
447 -(% style="color:blue" %)**AT Command: AT+CFM**
448 -
449 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
347 +(% style="background-color:#ffffcc; color:green; width:710.222px" %)
450 450  |=(% colspan="3" style="width: 707px;" %)AT+CFM
451 451  |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
452 452  |(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
... ... @@ -455,108 +455,56 @@
455 455  |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
456 456  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
457 457  
458 -(% style="color:blue" %)**Downlink Command: 0x05**
356 +Downlink Command: 0x05
459 459  
460 460  Format: Command Code (0x05) followed by 2 bytes mode value.
461 461  
462 462  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
463 463  
464 -* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
465 -* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
362 +* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
363 +* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
466 466  
467 -(% style="display:none" %) (%%)
468 -
469 -=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
470 -
471 -
472 -(% style="color:blue" %)**AT Command: AT+CFM**
473 -
474 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
475 -|=(% colspan="3" style="width: 707px;" %)AT+CFM
476 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
477 -|(% style="width:160px" %)(((
478 -AT+CFM=1,0,0
479 -
480 -value1
481 -)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
482 -1
483 -
484 -OK
485 -)))
486 -|(% style="width:160px" %)(((
487 -AT+CFM=0,?,0
488 -
489 -value2
490 -)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
491 -0~~7
492 -
493 -OK
494 -)))
495 -|(% style="width:160px" %)(((
496 -AT+CFM=0,0,1
497 -
498 -value3
499 -)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
500 -1
501 -
502 -OK
503 -)))
504 -
505 -(% style="color:blue" %)**Downlink Command: 0x05**
506 -
507 -Format: Command Code (0x05) followed by 2 bytes mode value.
508 -
509 -If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
510 -
511 -* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
512 -* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
513 -
514 -(% style="display:none" %) (%%)
515 -
516 516  == 6.2 Confirm Status ==
517 517  
518 -
519 519  Feature: Get confirmation status of the last AT+SEND (0-1).
520 520  
369 +{{info}}
370 +**AT Command: AT+CFS**
371 +{{/info}}
521 521  
522 -(% style="color:blue" %)**AT Command: AT+CFS**
523 -
524 -(% border="1" style="background-color:#ffffcc; color:green; width:463px" %)
525 -|=(% colspan="3" style="width: 460px;" %)AT+CFS
526 -|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:107px" %)**Response**
527 -|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:107px" %)0(((
373 +(% style="background-color:#ffffcc; color:green; width:534.222px" %)
374 +|=(% colspan="3" style="width: 531px;" %)AT+CFS
375 +|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
376 +|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
528 528  OK
529 529  )))
530 530  
531 -(% style="display:none" %) (%%)
532 -
533 533  == 6.3 Join LoRa® Network ==
534 534  
535 -
536 536  Feature: Join network.
537 537  
384 +{{info}}
385 +**AT Command: AT+JOIN**
386 +{{/info}}
538 538  
539 -(% style="color:blue" %)**AT Command: AT+JOIN**
540 -
541 -(% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
388 +(% style="background-color:#ffffcc; color:green; width:647.222px" %)
542 542  |=(% colspan="3" style="width: 644px;" %)AT+JOIN
543 543  |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
544 544  |(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
545 545  OK
393 +
546 546  While Error in format, return AT_BUSY_ERROR
547 547  )))
548 548  
549 -(% style="display:none" %) (%%)
550 -
551 551  == 6.4 LoRa® Network Join Mode ==
552 552  
553 -
554 554  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
555 555  
401 +{{info}}
402 +**AT Command: AT+NJM**
403 +{{/info}}
556 556  
557 -(% style="color:blue" %)**AT Command: AT+NJM**
558 -
559 -(% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
405 +(% style="background-color:#ffffcc; color:green; width:753.222px" %)
560 560  |=(% colspan="3" style="width: 750px;" %)AT+NJM
561 561  |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
562 562  |(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
... ... @@ -565,417 +565,313 @@
565 565  |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
566 566  |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
567 567  
568 -(% style="color:blue" %)**Downlink Command: 0x20**
414 +Downlink Command: 0x20
569 569  
570 570  Format: Command Code (0x20) followed by 1 bytes mode value.
571 571  
572 572  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
573 573  
574 -* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
575 -* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
420 +* Example 1: Downlink Payload: 2000 ~/~/ Set AT+NJM=O
421 +* Example 2: Downlink Payload: 2001 ~/~/ Set AT+NJM=1
576 576  
577 -(% style="display:none" %) (%%)
578 -
579 579  == 6.5 LoRa® Network Join Status ==
580 580  
581 -
582 582  Feature: LoRa® Network Join Status.
583 583  
427 +AT Command: AT+NJS
584 584  
585 -(% style="color:blue" %)**AT Command: AT+NJS**
586 -
587 -(% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
588 -|=(% colspan="3" style="width: 495px;" %)AT+NJS
589 -|(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
590 -|(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
429 +|=(% colspan="3" %)AT+NJS
430 +|**Command Example**|**Function**|**Response**
431 +|AT+NJS=?|Get the join status.|0(((
591 591  OK
592 592  )))
593 593  
594 -(% style="display:none" %) (%%)
595 -
596 596  == 6.6 Print Last Received Data in Raw Format ==
597 597  
598 -
599 599  Feature: Print Last Received Data in Raw Format<port:data>.
600 600  
439 +AT Command: AT+RECV
601 601  
602 -(% style="color:blue" %)**AT Command: AT+RECV**
603 -
604 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
605 -|=(% colspan="3" style="width: 584px;" %)AT+RECV
606 -|(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
607 -|(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
441 +|=(% colspan="3" %)AT+RECV
442 +|**Command Example**|**Function**|**Response**
443 +|AT+RECV=?|print last received data in raw format.|0:(((
608 608  OK
609 609  )))
610 610  
611 -(% style="display:none" %) (%%)
612 -
613 613  == 6.7 Print Last Received Data in Binary Format ==
614 614  
615 -
616 616  Feature: Print Last Received Data in Binary Format<port:data>.
617 617  
451 +AT Command: AT+RECVB
618 618  
619 -(% style="color:blue" %)**AT Command: AT+RECVB**
620 -
621 -(% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
622 -|=(% colspan="3" style="width: 790px;" %)AT+RECVB
623 -|(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
624 -|(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
453 +|=(% colspan="3" %)AT+RECVB
454 +|**Command Example**|**Function**|**Response**
455 +|AT+RECVB=?|print last received data in binary format (with hexadecimal values).|2: 0010(((
625 625  OK
626 626  )))
627 627  
628 -(% style="display:none" %) (%%)
629 -
630 630  == 6.8 Send Text Data ==
631 631  
632 -
633 633  Feature: Send Text Data<port:data>.
634 634  
463 +AT Command: AT+SEND
635 635  
636 -(% style="color:blue" %)**AT Command: AT+SEND**
637 -
638 -(% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
639 -|=(% colspan="3" style="width: 988px;" %)AT+SEND
640 -|(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
641 -|(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
465 +|=(% colspan="3" %)AT+SEND
466 +|**Command Example**|**Function**|**Response**
467 +|AT+SEND=12:hello world|Send text data along with the application port.|OK(((
642 642  While Error in format, return
469 +
643 643  AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
471 +
472 +
644 644  )))
645 645  
646 -(% style="display:none" %) (%%)
647 -
648 648  == 6.9 Send Hexadecimal Data ==
649 649  
650 -
651 651  Feature: Send hexadecimal data along with the application port.
652 652  
479 +AT Command: AT+SENDB
653 653  
654 -(% style="color:blue" %)**AT Command: AT+SENDB**
481 +|=(% colspan="3" %)AT+SENDB
482 +|**Command Example**|**Function**|**Response**
483 +|AT+SENDB=12:abcdef0123456789|Send hexadecimal data along with the application port.|OK
484 +|AT+SENDB=abcdef0123456789|Send hexadecimal data along with the application port.|While Error in format, return(((
485 +AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
655 655  
656 -(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
657 -|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
658 -|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
659 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
660 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
661 -AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
487 +
662 662  )))
663 663  
664 -(% style="display:none" %) (%%)
665 -
666 666  = 7. LoRaWAN network management =
667 667  
668 668  == 7.1 Adaptive Data Rate ==
669 669  
670 -
671 671  Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
672 672  
673 673  
674 -(% style="color:blue" %)**AT Command: AT+ADR**
497 +AT Command: AT+ADR
675 675  
676 -(% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
677 -|=(% colspan="3" style="width: 680px;" %)AT+ADR
678 -|(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
679 -|(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1(((
499 +|=(% colspan="3" %)AT+ADR
500 +|**Command Example**|**Function**|**Response**
501 +|AT+ADR=?|Get the Adaptive Data Rate setting.|1(((
680 680  OK
681 681  )))
682 -|(% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)OK
683 -|(% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)While Error in format, return(((
504 +|AT+ADR=0|Set the Adaptive Data Rate setting.|OK
505 +|AT+ADR=2|Set the Adaptive Data Rate setting.|While Error in format, return(((
684 684  AT_PARAM_ERROR
685 685  )))
686 686  
687 -(% style="color:blue" %)**Downlink Command: 0x22**
509 +Downlink Command: 0x22
688 688  
511 +
689 689  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
690 690  
691 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
692 -* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
514 +* Example 1: Downlink Payload: 2201 ~/~/ Set AT+ADR=1.
515 +* Example 2: Downlink Payload: 2200FFFF ~/~/ Set AT+ADR=0.
693 693  
694 -(% style="display:none" %) (%%)
695 -
696 696  == 7.2 LoRa® Class ==
697 697  
698 -
699 699  Feature: Get or Set the Device Class(Currently only support class A, class C).
700 700  
521 +AT Command:AT+CLASS
701 701  
702 -(% style="color:blue" %)**AT Command:  AT+CLASS**
703 -
704 -(% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
705 -|=(% colspan="3" style="width: 504px;" %)AT+CLASS
706 -|(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
707 -|(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
523 +|=(% colspan="3" %)AT+CLASS
524 +|**Command Example**|**Function**|**Response**
525 +|AT+CLASS=?|Get the Device Class.|A(((
708 708  OK
709 709  )))
710 -|(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
528 +|AT+CLASS=C|Set the Device Class.|OK(((
711 711  
712 712  )))
713 713  
714 -(% style="display:none" %)
715 -
716 -(% style="color:red" %)**Notice:**
717 -
718 -* Run AT+FDR before running AT+CLASS=C
719 -* After change to Class=C, Before OTAA Join Successfule, the end node will still shows to use CLASS=A for OTAA Joined. It will use CLASS=C after OTAA Join Succeccful.
720 -
721 -
722 722  == 7.3 Duty Cycle Setting ==
723 723  
534 +Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
724 724  
725 -Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
536 +AT Command:AT+DCS
726 726  
727 -
728 -(% style="color:blue" %)**AT Command:  AT+DCS**
729 -
730 -(% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
731 -|=(% colspan="3" style="width: 512px;" %)AT+DCS
732 -|(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
733 -|(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
538 +|=(% colspan="3" %)AT+DCS
539 +|**Command Example**|**Function**|**Response**
540 +|AT+DCS=?|Get the ETSI Duty Cycle setting.|1(((
734 734  OK
735 735  )))
736 -|(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
543 +|AT+DCS=1|Set the ETSI Duty Cycle setting.|OK(((
737 737  
738 738  )))
739 739  
740 -(% style="display:none" %) (%%)
741 -
742 742  == 7.4 Data Rate ==
743 743  
549 +Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
744 744  
745 -Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) .
551 +AT Command: AT+DR
746 746  
747 -(% style="color:red" %)
748 -**Notice:**
749 -
750 -* User need to set Adaptive Data Rate(ADR)=0 first. otherwise device will respond to server's ADR command and change the DR according to server auto-adjustment.
751 -* Data Rate specifies Spreading Factor. The mapping varies in different frequency bands. User can check this link for detail. [[rp2-1.0.3-lorawan-regional-parameters.pdf>>https://lora-alliance.org/resource_hub/rp2-1-0-3-lorawan-regional-parameters/]]
752 -
753 -(% style="color:blue" %)**AT Command: AT+DR**
754 -
755 -(% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
756 -|=(% colspan="3" style="width: 463px;" %)AT+DR
757 -|(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
758 -|(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
553 +|=(% colspan="3" %)AT+DR
554 +|**Command Example**|**Function**|**Response**
555 +|AT+DR=?|Get the Data Rate.|5(((
759 759  OK
760 760  )))
761 -|(% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((
558 +|AT+DR=2|Set the Data Rate.|OK(((
762 762  
763 763  )))
764 764  
765 -(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
562 +Downlink Command: 0x2200aaFF
766 766  
564 +
767 767  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
768 768  
769 -* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
770 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
567 +* Example 1: Downlink Payload: 220001FF ~/~/ Set AT+DR=1.
568 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+DR=0.
771 771  
772 -(% style="display:none" %) (%%)
773 -
774 774  == 7.5 Frame Counter Downlink ==
775 775  
776 -
777 777  Feature: Get or Set the Frame Counter Downlink.
778 778  
574 +AT Command:AT+FCD
779 779  
780 -(% style="color:blue" %)**AT Command:  AT+FCD**
781 -
782 -(% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
783 -|=(% colspan="3" style="width: 690px;" %)AT+FCD
784 -|(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
785 -|(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
576 +|=(% colspan="3" %)AT+FCD
577 +|**Command Example**|**Function**|**Response**
578 +|AT+FCD=?|Get the Frame Counter Downlink.|0(((
786 786  OK
787 787  )))
788 -|(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
581 +|AT+FCD=10|Set the Frame Counter Downlink.|(System will write new value to FCD)(((
789 789  OK
583 +
584 +
790 790  )))
791 791  
792 -(% style="display:none" %) (%%)
793 -
794 794  == 7.6 Frame Counter Uplink ==
795 795  
796 796  Feature: Get or Set the Frame Counter Uplink.
797 797  
591 +AT Command:AT+FCU
798 798  
799 -(% style="color:blue" %)**AT Command:  AT+FCU**
800 -
801 -(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
802 -|=(% colspan="3" style="width: 531px;" %)AT+FCU
803 -|(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
804 -|(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
593 +|=(% colspan="3" %)AT+FCU
594 +|**Command Example**|**Function**|**Response**
595 +|AT+FCU=?|Get the Frame Counter Uplink.|0(((
805 805  OK
806 806  )))
807 -|(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
598 +|AT+FCU=10|Set the Frame Counter Uplink.|OK(((
808 808  
809 809  )))
810 810  
811 -(% style="display:none" %) (%%)
812 -
813 813  == 7.7 Join Accept Delay1 ==
814 814  
815 -
816 816  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
817 817  
606 +AT Command:AT+JN1DL
818 818  
819 -(% style="color:blue" %)**AT Command:  AT+JN1DL**
820 -
821 -(% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
822 -|=(% colspan="3" style="width: 534px;" %)AT+JN1DL
823 -|(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
824 -|(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
608 +|=(% colspan="3" %)AT+JN1DL
609 +|**Command Example**|**Function**|**Response**
610 +|AT+JN1DL=?|Get the Join Accept Delay.|5000(((
825 825  OK
826 826  )))
827 -|(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
613 +|AT+JN1DL=10000|Set the Join Accept Delay.|OK(((
828 828  
829 829  )))
830 830  
831 -(% style="display:none" %) (%%)
832 -
833 833  == 7.8 Join Accept Delay2 ==
834 834  
835 -
836 836  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
837 837  
621 +AT Command:AT+JN2DL
838 838  
839 -(% style="color:blue" %)**AT Command:  AT+JN2DL**
840 -
841 -(% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
842 -|=(% colspan="3" style="width: 535px;" %)AT+JN2DL
843 -|(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
844 -|(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
623 +|=(% colspan="3" %)AT+JN2DL
624 +|**Command Example**|**Function**|**Response**
625 +|AT+JN2DL=?|Get the Join Accept Delay.|6000(((
845 845  OK
846 846  )))
847 -|(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
628 +|AT+JN2DL=20000|Set the Join Accept Delay.|OK(((
848 848  
849 849  )))
850 850  
851 -(% style="display:none" %) (%%)
852 -
853 853  == 7.9 Public Network Mode ==
854 854  
634 +Feature: Get or Set the public network mode. (0: off, 1: on)
855 855  
856 -Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
636 +AT Command:AT+PNM
857 857  
858 -(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
859 -
860 -
861 -(% style="color:blue" %)**AT Command:  AT+PNM**
862 -
863 -(% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
864 -|=(% colspan="3" style="width: 664px;" %)AT+PNM
865 -|(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
866 -|(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
638 +|=(% colspan="3" %)AT+PNM
639 +|**Command Example**|**Function**|**Response**
640 +|AT+PNM=?|Get the public network mode.|1(((
867 867  OK
868 868  )))
869 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
870 -Set the public network mode.
871 -
872 -Set syncword=0x34
873 -)))|(% style="width:272px" %)(System will write new value to PNM)(((
643 +|AT+PNM=1|Set the public network mode.|(System will write new value to PNM)(((
874 874  OK
875 875  
876 876  
877 877  )))
878 -|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
879 879  
880 -(% style="display:none" %) (%%)
881 -
882 882  == 7.10 Receive Delay1 ==
883 883  
884 -
885 885  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
886 886  
653 +AT Command:AT+RX1DL
887 887  
888 -(% style="color:blue" %)**AT Command: AT+RX1DL**
889 -
890 -(% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
891 -|=(% colspan="3" style="width: 405px;" %)AT+RX1DL
892 -|(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
893 -|(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
655 +|=(% colspan="3" %)AT+RX1DL
656 +|**Command Example**|**Function**|**Response**
657 +|AT+RX1DL=?|Get the delay.|1000(((
894 894  OK
895 895  )))
896 -|(% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((
660 +|AT+RX1DL=1500|Set the delay.|OK(((
897 897  
898 898  )))
899 899  
900 -(% style="display:none" %) (%%)
664 +== 7.11Receive Delay2 ==
901 901  
902 -== 7.11 Receive Delay2 ==
903 -
904 -
905 905  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
906 906  
668 +AT Command:AT+RX2DL
907 907  
908 -(% style="color:blue" %)**AT Command: AT+RX2DL**
909 -
910 -(% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
911 -|=(% colspan="3" style="width: 478px;" %)AT+RX2DL
912 -|(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
913 -|(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
670 +|=(% colspan="3" %)AT+RX2DL
671 +|**Command Example**|**Function**|**Response**
672 +|AT+RX2DL=?|Get the delay.|2000(((
914 914  OK
915 915  )))
916 -|(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
675 +|AT+RX2DL=2500|Set the delay.|OK(((
917 917  
918 918  )))
919 919  
920 -(% style="display:none" %) (%%)
921 -
922 922  == 7.12 Rx2 Window Data Rate ==
923 923  
924 -
925 925  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
926 926  
683 +AT Command:AT+RX2DR
927 927  
928 -(% style="color:blue" %)**AT Command:  AT+RX2DR**
929 -
930 -(% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
931 -|=(% colspan="3" style="width: 522px;" %)AT+RX2DR
932 -|(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
933 -|(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
685 +|=(% colspan="3" %)AT+RX2DR
686 +|**Command Example**|**Function**|**Response**
687 +|AT+RX2DR=?|Get the Rx2 window data rate.|2(((
934 934  OK
935 935  )))
936 -|(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
690 +|AT+RX2DR=6|Set the Rx2 window data rate.|OK(((
937 937  
938 938  )))
939 939  
940 -(% style="display:none" %) (%%)
941 -
942 942  == 7.13 Rx2 Window Frequency ==
943 943  
944 -
945 945  Feature: Get or Set the Rx2 window frequency
946 946  
698 +AT Command:AT+RX2FQ
947 947  
948 -(% style="color:blue" %)**AT Command:  AT+RX2FQ**
949 -
950 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
951 -|=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
952 -|(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
953 -|(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
700 +|=(% colspan="3" %)AT+RX2FQ
701 +|**Command Example**|**Function**|**Response**
702 +|AT+RX2FQ=?|Get the Rx2 window frequency.|434665000(((
954 954  OK
955 955  )))
956 -|(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
705 +|AT+RX2FQ=434665000|Set the Rx2 window frequency.|OK(((
957 957  
958 958  )))
959 959  
960 -(% style="display:none" %) (%%)
961 -
962 962  == 7.14 Transmit Power ==
963 963  
964 -
965 965  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
966 966  
967 -(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
713 +AT Command:AT+TXP
968 968  
969 -
970 -(% style="color:blue" %)**AT Command:  AT+TXP**
971 -
972 -(% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
973 -|=(% colspan="3" style="width: 462px;" %)AT+TXP
974 -|(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
975 -|(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
715 +|=(% colspan="3" %)AT+TXP
716 +|**Command Example**|**Function**|**Response**
717 +|AT+TXP=?|Get the Transmit Power.|0(((
976 976  OK
977 977  )))
978 -|(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
720 +|AT+TXP=1|Set the Transmit Power.|OK(((
979 979  
980 980  )))
981 981  
... ... @@ -983,389 +983,195 @@
983 983  
984 984  If the downlink payload=22000100, it means setting the TXP to 0.
985 985  
986 -* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
987 -* **Example 2**: Downlink Payload: **22000000**  ~/~/ Set AT+TXP=0.
728 +* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2.
729 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0.
988 988  
989 -(% style="display:none" %) (%%)
990 -
991 991  == 7.15 RSSI of the Last Received Packet ==
992 992  
993 -
994 994  Feature: Get or Set the Rx2 window frequency
995 995  
735 +AT Command:AT+RSSI
996 996  
997 -(% style="color:blue" %)**AT Command:AT+RSSI**
998 -
999 -(% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
1000 -|=(% colspan="3" style="width: 554px;" %)AT+RSSI
1001 -|(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
1002 -|(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
737 +|=(% colspan="3" %)AT+RSSI
738 +|**Command Example**|**Function**|**Response**
739 +|AT+RSSI=?|Get the RSSI of the last received packet.|0(((
1003 1003  OK
1004 1004  )))
1005 1005  
1006 -(% style="display:none" %) (%%)
1007 -
1008 1008  == 7.16 SNR of the Last Received Packet ==
1009 1009  
1010 -
1011 1011  Feature: Get the SNR of the last received packet
1012 1012  
747 +AT Command:AT+SNR
1013 1013  
1014 -(% style="color:blue" %)**AT Command:  AT+SNR**
1015 -
1016 -(% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
1017 -|=(% colspan="3" style="width: 568px;" %)AT+SNR
1018 -|(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
1019 -|(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
749 +|=(% colspan="3" %)AT+SNR
750 +|**Command Example**|**Function**|**Response**
751 +|AT+SNR=?|Get the RSSI of the last received packet.|0(((
1020 1020  OK
1021 1021  )))
1022 1022  
1023 -(% style="display:none" %) (%%)
1024 -
1025 1025  == 7.17 Application Port ==
1026 1026  
1027 -
1028 1028  Feature: Get or set the application port.
1029 1029  
759 +AT Command: AT+PORT
1030 1030  
1031 -(% style="color:blue" %)**AT Command: AT+PORT**
1032 -
1033 -(% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
1034 -|=(% colspan="3" style="width: 497px;" %)AT+PORT
1035 -|(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
1036 -|(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
761 +|=(% colspan="3" %)AT+PORT
762 +|**Command Example**|**Function**|**Response**
763 +|AT+PORT=?|Get the application port|21(((
1037 1037  OK
1038 1038  )))
1039 -|(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
766 +|AT+PORT=21|Set the application port|OK
1040 1040  
1041 -(% style="color:blue" %)**Downlink Command: 0x23**
768 +Downlink Command: 0x23
1042 1042  
1043 1043  Format: Command Code (0x23) followed by 1 bytes port value.
1044 1044  
1045 1045  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1046 1046  
1047 -* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1048 -* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
774 +* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1
775 +* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5
1049 1049  
1050 -(% style="display:none" %) (%%)
1051 -
1052 1052  == 7.18 Single Channel Mode ==
1053 1053  
1054 -
1055 1055  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
1056 1056  
781 +AT Command: AT+CHS
1057 1057  
1058 -(% style="color:blue" %)**AT Command: AT+CHS**
1059 -
1060 -(% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
1061 -|=(% colspan="3" style="width: 600px;" %)AT+CHS
1062 -|(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
1063 -|(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
783 +|=(% colspan="3" %)AT+CHS
784 +|**Command Example**|**Function**|**Response**
785 +|AT+CHS=?|Get Frequency for Single Channel Mode|0(((
1064 1064  OK
1065 1065  )))
1066 -|(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
788 +|AT+CHS=868100000|Set Frequency for Single Channel Mode|OK
1067 1067  
1068 -(% style="display:none" %) (%%)
1069 -
1070 1070  == 7.19 Eight Channel Mode ==
1071 1071  
1072 -
1073 1073  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1074 1074  
794 +AT Command: AT+CHE
1075 1075  
1076 -(% style="color:blue" %)**AT Command: AT+CHE**
1077 -
1078 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1079 -|=(% colspan="3" style="width: 707px;" %)AT+CHE
1080 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1081 -|(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
796 +|=(% colspan="3" %)AT+CHE
797 +|**Command Example**|**Function**|**Response**
798 +|AT+CHE=?|Get eight channels mode|1(((
1082 1082  902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
1083 1083  
1084 1084  OK
1085 1085  )))
1086 -|(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
803 +|AT+CHE=1|Set eight channels mode|OK
1087 1087  
1088 -(% style="color:blue" %)**Downlink Command: 0x24 (LHT65,LHT65N Downlink Command:0x07)**
805 +Downlink Command: 0x24
1089 1089  
1090 1090  Format: Command Code (0x24) followed by 1 bytes channel value.
1091 1091  
1092 1092  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1093 1093  
1094 -* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1095 -* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
811 +* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1
812 +* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5
1096 1096  
1097 -(% style="display:none" %) (%%)
1098 -
1099 1099  == 7.20 Get or Set RXwindows1 timeout ==
1100 1100  
816 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1101 1101  
1102 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
818 +AT Command: AT+RX1WTO
1103 1103  
1104 -
1105 -(% style="color:blue" %)**AT Command: AT+RX1WTO**
1106 -
1107 -(% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1108 -|=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1109 -|(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
1110 -|(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
820 +|=(% colspan="3" %)AT+ RX1WTO
821 +|**Command Example**|**Function**|**Response**
822 +|AT+RX1WTO=?|Get RXwindows1 timeout|14(((
1111 1111  OK
1112 1112  )))
1113 -|(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
825 +|AT+RX1WTO=60|Set RXwindows1 timeout|OK
1114 1114  
1115 -(% style="display:none" %) (%%)
827 +AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1116 1116  
1117 -(((
1118 -(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1119 -)))
829 +[[~[~[image:https://wiki.dragino.com/images/thumb/5/51/RX1WTO.JPG/600px-RX1WTO.JPG~|~|alt="RX1WTO.JPG" height="239" width="600"~]~]>>url:https://wiki.dragino.com/index.php/File:RX1WTO.JPG]]
1120 1120  
1121 -[[image:image-20220526162535-1.png]]
1122 -
1123 -(((
1124 1124  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1125 -)))
1126 1126  
1127 -
1128 1128  == 7.21 Get or Set RXwindows2 timeout ==
1129 1129  
835 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1130 1130  
1131 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
837 +AT Command: AT+RX2WTO
1132 1132  
1133 -
1134 -(% style="color:blue" %)**AT Command: AT+RX2WTO**
1135 -
1136 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1137 -|=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1138 -|(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
1139 -|(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
839 +|=(% colspan="3" %)AT+ RX2WTO
840 +|**Command Example**|**Function**|**Response**
841 +|AT+RX2WTO=?|Get RXwindows2 timeout|7(((
1140 1140  OK
1141 1141  )))
1142 -|(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
844 +|AT+RX2WTO=20|Set RXwindows2 timeout|OK
1143 1143  
1144 -(% style="display:none" %) (%%)
1145 -
1146 1146  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1147 1147  
1148 -
1149 1149  Feature: Get or Set uplinkdwelltime
1150 1150  
850 +AT Command: AT+DWELLT
1151 1151  
1152 -(% style="color:blue" %)**AT Command: AT+DWELLT**
1153 -
1154 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1155 -|=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1156 -|(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
1157 -|(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
852 +|=(% colspan="3" %)AT+DWELLT
853 +|**Command Example**|**Function**|**Response**
854 +|AT+DWELLT=?|Get uplinkdwelltime|1(((
1158 1158  OK
1159 1159  )))
1160 -|(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
857 +|AT+DWELLT=0|Set uplinkdwelltime|OK
1161 1161  
1162 -(% style="color:blue" %)**Downlink Command: 0x25**
859 +Downlink Command: 0x25
1163 1163  
1164 1164  Format: Command Code (0x25) followed by 1 bytes state value.
1165 1165  
1166 1166  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1167 1167  
1168 -* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1169 -* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
865 +* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1
866 +* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0
1170 1170  
1171 -(% style="display:none" %) (%%)
1172 -
1173 1173  == 7.23 Set Packet Receiving Response Level ==
1174 1174  
1175 -
1176 1176  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1177 1177  
872 +RPL value:
1178 1178  
1179 -**RPL value:**
874 +* AT+RPL=0: Device won't immediately reply any downlink commands from platform.
875 +* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
876 +* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
877 +* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
878 +* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1180 1180  
1181 -* **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1182 -* **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1183 -* **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1184 -* **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1185 -* **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
880 +Case Analyes:
1186 1186  
1187 -**Case Analyes:**
1188 -
1189 1189  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1190 1190  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1191 1191  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1192 1192  
1193 -(% style="color:blue" %)**AT Command: AT+RPL**
886 +AT Command: AT+RPL
1194 1194  
1195 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1196 -|=(% colspan="3" style="width: 533px;" %)AT+RPL
1197 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1198 -|(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
888 +|=(% colspan="3" %)AT+RPL
889 +|**Command Example**|**Function**|**Response**
890 +|AT+RPL=?|Get packet receiving response level|1(((
1199 1199  OK
1200 1200  )))
1201 -|(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
893 +|AT+RPL=0|Set packet receiving response level|OK
1202 1202  
1203 -(% style="color:blue" %)**Downlink Command: 0x21**
895 +Downlink Command: 0x21
1204 1204  
1205 1205  Format: Command Code (0x21) followed by 1 bytes level value.
1206 1206  
1207 1207  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1208 1208  
1209 -* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1210 -* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
901 +* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1
902 +* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2
1211 1211  
1212 -(% style="display:none" %) (%%)
1213 -
1214 -== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1215 -
1216 -
1217 -(% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1218 -
1219 -(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1220 -|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1221 -|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1222 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1223 -OK
1224 -)))
1225 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1226 -value2: 0: uplink fcnt doesn't change for each NBTrans;
1227 -
1228 -1: uplink fcnt increase by 1 for each NBTrans.
1229 -)))|(% style="width:87px" %)(((
1230 -1
1231 -
1232 -OK
1233 -)))
1234 -
1235 -(% style="color:blue" %)**Downlink Command: 0x33**
1236 -
1237 -Format: Command Code (0x33) followed by 2 bytes mode value.
1238 -
1239 -If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1240 -
1241 -* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1242 -* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1243 -
1244 -(% style="display:none" %) (%%)
1245 -
1246 -== 7.25 Device offline rejoining （LWS007) ==
1247 -
1248 -
1249 -(% style="color:blue" %)**AT Command: AT+DDETECT**
1250 -
1251 -AT+DDETECT=<Flag>,<ACK_Timout_1>,<ACK_Timout_2> (Default Value: AT+DDETECT=1,1440,2880)
1252 -
1253 -* ACK_Timout_1: Unit: min
1254 -* ACK_Timout_2: Unit: min
1255 -
1256 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1257 -|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1258 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1259 -|(% style="width:160px" %)(((
1260 -AT+DDETECT=1,1440,2880
1261 -
1262 -value1
1263 -)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1264 -1
1265 -
1266 -OK
1267 -)))
1268 -|(% style="width:160px" %)(((
1269 -AT+DDETECT=1,?,2880
1270 -
1271 -value2
1272 -)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1273 -
1274 -
1275 -OK
1276 -)))
1277 -|(% style="width:160px" %)(((
1278 -AT+DDETECT=1,1440,？
1279 -
1280 -value3
1281 -)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1282 -
1283 -
1284 -OK
1285 -)))
1286 -
1287 -(% style="color:blue" %)**Downlink Command: 0x32**
1288 -
1289 -Format: Command Code (0x32) followed by 2 bytes mode value.
1290 -
1291 -If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 32.
1292 -
1293 -* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1294 -** 0x01 : Flag
1295 -** 0x05A0: ACK_Timout_1 : 1440minutes (24 hours)
1296 -** 0x0B40: ACK_Timout_2 : 2880minutes (48 hours)
1297 -** **Explain**: Enable Online Detect, if end node doesn't receive any downlink within ACK_Timout_1( 1440 minutes or 24 hours). End node will use confirmed uplink to send packets during ACK_Timout_1 (the 24th hour) to ACK_Timout_2 ( the 48th hour). If from the 24th to 48th hour, end node got an downlink from server, it will switch back to unconfirmed uplink. end node will restart ACK_Timout_1. If from the 24th to 48th hour, end node still not got any downlink, means device doesn't get ACK from server within last 48 hours. Device will process rejoin, rejoin request interval is AT+RJTDC period. For AU915/ US915, device will use the sub-band used for last join.
1298 -
1299 -(% style="display:none" %) (%%)
1300 -
1301 -== 7.26 Request the server to send an ACK ==
1302 -
1303 -
1304 -(% style="color:blue" %)**AT Command: AT+PNACKMD**
1305 -
1306 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1307 -|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1308 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1309 -|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1310 -OK
1311 -)))
1312 -|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1313 -0
1314 -OK
1315 -)))
1316 -
1317 -(% style="display:none" %) (%%)
1318 -
1319 -== 7.27 Adjust network rejoining interval ==
1320 -
1321 -
1322 -(% style="color:blue" %)**AT Command: AT+RJTDC**
1323 -
1324 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1325 -|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1326 -|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1327 -|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30(((
1328 -OK
1329 -
1330 -the interval is 30 min
1331 -)))
1332 -|(% style="width:165px" %)AT+RJTDC=60|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1333 -Set the ReJoin data transmission interval to 60 min
1334 -)))
1335 -
1336 -(% style="color:blue" %)**Downlink Command: 0x26**
1337 -
1338 -Format: Command Code (0x26) followed by 2 bytes mode value.
1339 -
1340 -If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1341 -
1342 -* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1343 -* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1344 -
1345 -(% style="display:none" %) (%%)
1346 -
1347 1347  = 8. AT Commands Combination =
1348 1348  
1349 1349  == 8.1 Set a fix RX2DR for downlink window ==
1350 1350  
908 +* AT+ADR=0 ~-~-> Disable ADR first
909 +* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate
1351 1351  
1352 -* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1353 -
1354 -* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1355 -
1356 -(% style="display:none" %) (%%)
1357 -
1358 1358  == 8.2 Use Downlink Command to set a fix uplink DR ==
1359 1359  
913 +Downlink Command: 0x22000500
1360 1360  
1361 -(% style="color:blue" %)**Downlink Command: 0x22000500**
915 +Same as:
1362 1362  
1363 -**Same as:**
1364 -
1365 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1366 -
1367 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1368 -
1369 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1370 -
1371 -
917 +* AT+ADR=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Adaptive_Data_Rate]]
918 +* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]]
919 +* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]
image-20220511120050-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -136.3 KB
Content
image-20220526162535-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -149.4 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0