Last modified by kai on 2024/09/06 10:00
<
From version < 60.5 >
edited by Xiaoling
on 2023/03/27 14:01
To version < 60.9 >
edited by Xiaoling
on 2023/03/27 14:07
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -708,6 +708,7 @@
708 708  OK
709 709  )))
710 710  |(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
711 +
711 711  )))
712 712  
713 713  (% style="display:none" %) (%%)
... ... @@ -727,6 +727,7 @@
727 727  OK
728 728  )))
729 729  |(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
731 +
730 730  )))
731 731  
732 732  (% style="display:none" %) (%%)
... ... @@ -795,6 +795,7 @@
795 795  OK
796 796  )))
797 797  |(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
800 +
798 798  )))
799 799  
800 800  (% style="display:none" %) (%%)
... ... @@ -814,6 +814,7 @@
814 814  OK
815 815  )))
816 816  |(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
820 +
817 817  )))
818 818  
819 819  (% style="display:none" %) (%%)
... ... @@ -833,6 +833,7 @@
833 833  OK
834 834  )))
835 835  |(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
840 +
836 836  )))
837 837  
838 838  (% style="display:none" %) (%%)
... ... @@ -864,6 +864,8 @@
864 864  )))
865 865  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
866 866  
872 +(% style="display:none" %) (%%)
873 +
867 867  == 7.10 Receive Delay1 ==
868 868  
869 869  
... ... @@ -882,6 +882,8 @@
882 882  
883 883  )))
884 884  
892 +(% style="display:none" %) (%%)
893 +
885 885  == 7.11 Receive Delay2 ==
886 886  
887 887  
... ... @@ -900,6 +900,8 @@
900 900  
901 901  )))
902 902  
912 +(% style="display:none" %) (%%)
913 +
903 903  == 7.12 Rx2 Window Data Rate ==
904 904  
905 905  
... ... @@ -918,6 +918,8 @@
918 918  
919 919  )))
920 920  
932 +(% style="display:none" %) (%%)
933 +
921 921  == 7.13 Rx2 Window Frequency ==
922 922  
923 923  
... ... @@ -936,6 +936,8 @@
936 936  
937 937  )))
938 938  
952 +(% style="display:none" %) (%%)
953 +
939 939  == 7.14 Transmit Power ==
940 940  
941 941  
... ... @@ -963,6 +963,8 @@
963 963  * **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
964 964  * **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
965 965  
981 +(% style="display:none" %) (%%)
982 +
966 966  == 7.15 RSSI of the Last Received Packet ==
967 967  
968 968  
... ... @@ -978,6 +978,8 @@
978 978  OK
979 979  )))
980 980  
998 +(% style="display:none" %) (%%)
999 +
981 981  == 7.16 SNR of the Last Received Packet ==
982 982  
983 983  
... ... @@ -993,6 +993,8 @@
993 993  OK
994 994  )))
995 995  
1015 +(% style="display:none" %) (%%)
1016 +
996 996  == 7.17 Application Port ==
997 997  
998 998  
... ... @@ -1018,6 +1018,8 @@
1018 1018  * **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1019 1019  * **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1020 1020  
1042 +(% style="display:none" %) (%%)
1043 +
1021 1021  == 7.18 Single Channel Mode ==
1022 1022  
1023 1023  
... ... @@ -1034,6 +1034,8 @@
1034 1034  )))
1035 1035  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1036 1036  
1060 +(% style="display:none" %) (%%)
1061 +
1037 1037  == 7.19 Eight Channel Mode ==
1038 1038  
1039 1039  
... ... @@ -1061,6 +1061,8 @@
1061 1061  * **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1062 1062  * **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1063 1063  
1089 +(% style="display:none" %) (%%)
1090 +
1064 1064  == 7.20 Get or Set RXwindows1 timeout ==
1065 1065  
1066 1066  
... ... @@ -1077,24 +1077,19 @@
1077 1077  )))
1078 1078  |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1079 1079  
1080 -(((
1081 -
1107 +(% style="display:none" %) (%%)
1082 1082  
1083 -
1109 +(((
1084 1084  (% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1085 -
1086 -
1087 1087  )))
1088 1088  
1089 1089  [[image:image-20220526162535-1.png]]
1090 1090  
1091 -
1092 1092  (((
1093 1093  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1094 -
1095 -
1096 1096  )))
1097 1097  
1119 +
1098 1098  == 7.21 Get or Set RXwindows2 timeout ==
1099 1099  
1100 1100  
... ... @@ -1111,6 +1111,8 @@
1111 1111  )))
1112 1112  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1113 1113  
1136 +(% style="display:none" %) (%%)
1137 +
1114 1114  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1115 1115  
1116 1116  
... ... @@ -1136,6 +1136,8 @@
1136 1136  * **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1137 1137  * **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1138 1138  
1163 +(% style="display:none" %) (%%)
1164 +
1139 1139  == 7.23 Set Packet Receiving Response Level ==
1140 1140  
1141 1141  
... ... @@ -1175,6 +1175,8 @@
1175 1175  * **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1176 1176  * **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1177 1177  
1204 +(% style="display:none" %) (%%)
1205 +
1178 1178  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1179 1179  
1180 1180  
... ... @@ -1205,6 +1205,8 @@
1205 1205  * Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1206 1206  * Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1207 1207  
1236 +(% style="display:none" %) (%%)
1237 +
1208 1208  == 7.25 Device offline rejoining （LWS007) ==
1209 1209  
1210 1210  
... ... @@ -1258,6 +1258,8 @@
1258 1258  ** 0x0B40: ACK_Timout_2 : 2880minutes (48 hours)
1259 1259  ** **Explain**: Enable Online Detect, if end node doesn't receive any downlink within ACK_Timout_1( 1440 minutes or 24 hours). End node will use confirmed uplink to send packets during ACK_Timout_1 (the 24th hour) to ACK_Timout_2 ( the 48th hour). If from the 24th to 48th hour, end node got an downlink from server, it will switch back to unconfirmed uplink. end node will restart ACK_Timout_1. If from the 24th to 48th hour, end node still not got any downlink, means device doesn't get ACK from server within last 48 hours. Device will process rejoin, rejoin request interval is AT+RJTDC period. For AU915/ US915, device will use the sub-band used for last join.
1260 1260  
1291 +(% style="display:none" %) (%%)
1292 +
1261 1261  == 7.26 Request the server to send an ACK ==
1262 1262  
1263 1263  
... ... @@ -1271,10 +1271,11 @@
1271 1271  )))
1272 1272  |(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1273 1273  0
1274 -
1275 1275  OK
1276 1276  )))
1277 1277  
1309 +(% style="display:none" %) (%%)
1310 +
1278 1278  == 7.27 Adjust network rejoining interval ==
1279 1279  
1280 1280  
... ... @@ -1301,6 +1301,8 @@
1301 1301  * **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1302 1302  * **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1303 1303  
1337 +(% style="display:none" %) (%%)
1338 +
1304 1304  = 8. AT Commands Combination =
1305 1305  
1306 1306  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1307,8 +1307,11 @@
1307 1307  
1308 1308  
1309 1309  * (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1345 +
1310 1310  * (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1311 1311  
1348 +(% style="display:none" %) (%%)
1349 +
1312 1312  == 8.2 Use Downlink Command to set a fix uplink DR ==
1313 1313  
1314 1314  
... ... @@ -1317,7 +1317,9 @@
1317 1317  **Same as:**
1318 1318  
1319 1319  * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1358 +
1320 1320  * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1360 +
1321 1321  * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1322 1322  
1323 1323  

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0