Last modified by kai on 2024/09/06 10:00
<
From version < 60.3 >
edited by Xiaoling
on 2023/03/27 13:52
To version < 7.6 >
edited by Xiaoling
on 2022/05/11 10:27
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,118 +1,55 @@
1 - **Table of** **Contents：**
1 +Contens
2 2  
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 -
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 -* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
10 +* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
11 +* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 -(((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 -)))
14 +
18 18  
19 -
20 20  = 2. How to use AT Commands or Downlink command =
21 21  
18 +* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
19 +* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
20 +** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
21 +** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
22 +** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
22 22  
23 -* **AT Command** : See Devices User Manual for how to connect to device via USB TTL adapter and use. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
24 -* **LoRaWAN Downlink Command**: The gateway transfer downlink command in HEX format. This page shows the Downlink Command In HEX format. Please note some LoRaWAN servers use base64 as downlink code so user need to convert HEX to Base64 and use. Below are references for how to use downlink command:
25 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
26 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]], [[How to Convert>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.1ConvertHEXtoBase64]]?
27 -** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
28 -
29 -(% style="display:none" %) (%%)
30 -
31 31  = 3. Support End Node and firmware version =
32 32  
33 -
34 -(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
35 -|=(% colspan="3" style="width: 963px;" %)(((
36 -Dragino STM32 base hardware Firmware / LoRaWAN stack list
37 -)))
38 -|(% style="width:187px" %)(((
39 -**Model**
40 -)))|(% style="width:330px" %)(((
41 -**Description**
42 -)))|(% style="width:445px" %)(((
43 -**Firmware Version <~-~-> Stack Version**
44 -)))
45 -|(% style="width:187px" %)(((
46 -[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
47 -)))|(% style="width:330px" %)(((
48 -Open Source Generic LoRaWAN Sensor Node
49 -)))|(% style="width:445px" %)(((
50 -(((
51 -LSN50 v1.6.0 <~-~-> DR-LWS-003;
52 -)))
53 -
54 -(((
55 -(((
26 +(% style="background-color:#ffffcc; color:green; width:995.222px" %)
27 +|=(% colspan="3" style="width: 992px;" %)Dragino STM32 base hardware Firmware / LoRaWAN stack list
28 +|(% style="width:187px" %)**Model**|(% style="width:349px" %)**Description**|(% style="width:453px" %)**Firmware Version <~-~-> Stack Version**
29 +|(% style="width:187px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:349px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:453px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;(((
56 56  LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
57 57  )))
58 -)))
59 -)))
60 -|(% style="width:187px" %)(((
61 -[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
62 -)))|(% style="width:330px" %)(((
63 -LoRaWAN GPS Tracker
64 -)))|(% style="width:445px" %)(((
65 -(((
66 -LGT92 v1.6.3 <~-~-> DR-LWS-003;
67 -)))
68 -
69 -(((
70 -(((
32 +|(% style="width:187px" %)[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],|(% style="width:349px" %)LoRaWAN GPS Tracker|(% style="width:453px" %)LGT92 v1.6.3 <~-~-> DR-LWS-003;(((
71 71  LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
72 72  )))
73 -)))
74 -)))
75 -|(% style="width:187px" %)(((
76 -[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
77 -)))|(% style="width:330px" %)(((
78 -LoRaWAN BLE Indoor Tracker
79 -)))|(% style="width:445px" %)(((
80 -LBT1 v1.0 <~-~-> DR-LWS-005;
81 -)))
82 -|(% style="width:187px" %)(((
83 -[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
84 -)))|(% style="width:330px" %)(((
85 -LoRaWAN RS485 Modbus Converter
86 -)))|(% style="width:445px" %)(((
87 -RS485-LN v1.3 <~-~-> DR-LWS-005;
88 -)))
89 -|(% style="width:187px" %)(((
90 -[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
91 -)))|(% style="width:330px" %)(((
92 -LoRaWAN Temperature & Humidity Sensor
93 -)))|(% style="width:445px" %)(((
94 -(((
95 -LHT65 v1.7 <~-~-> DR-LWS-003;
96 -)))
97 -
98 -(((
99 -(((
35 +|(% style="width:187px" %)[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],|(% style="width:349px" %)LoRaWAN BLE Indoor Tracker|(% style="width:453px" %)LBT1 v1.0 <~-~-> DR-LWS-005;
36 +|(% style="width:187px" %)[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],|(% style="width:349px" %)LoRaWAN RS485 Modbus Converter|(% style="width:453px" %)RS485-LN v1.3 <~-~-> DR-LWS-005;
37 +|(% style="width:187px" %)[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],|(% style="width:349px" %)LoRaWAN Temperature & Humidity Sensor|(% style="width:453px" %)LHT65 v1.7 <~-~-> DR-LWS-003;(((
100 100  LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
101 101  )))
102 -)))
103 -)))
104 104  
105 105  = 4. System Management Commands =
106 106  
107 107  == 4.1 Change Uplink Interval ==
108 108  
109 -
110 110  Feature: Change LoRaWAN End Node Transmit Interval.
111 111  
47 +(% class="box infomessage" %)
48 +(((
49 +**AT Command: AT+TDC**
50 +)))
112 112  
113 -(% style="color:blue" %)**AT Command: AT+TDC**
114 -
115 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
52 +(% style="background-color:#ffffcc; color:green; width:727.222px" %)
116 116  |=(% colspan="3" style="width: 724px;" %)AT+TDC
117 117  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
118 118  |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
... ... @@ -124,33 +124,29 @@
124 124  Set transmit interval to 60000ms = 60 seconds
125 125  )))
126 126  
127 -(((
128 -
64 +{{info}}
65 +**Downlink Command: 0x01**
66 +{{/info}}
129 129  
130 -(% style="color:blue" %)**Downlink Command: 0x01**
131 -
132 132  Format: Command Code (0x01) followed by 3 bytes time value.
133 -)))
134 134  
135 -(((
136 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
137 -)))
70 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
138 138  
139 -* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
140 -* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
72 +* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
73 +* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
141 141  
142 142  == 4.2 Reboot End Node ==
143 143  
144 -
145 145  Feature: Reboot End Node to perform a new OTAA or ABP Join.
146 146  
79 +{{info}}
80 +**AT Command: ATZ**
81 +{{/info}}
147 147  
148 -(% style="color:blue" %)**AT Command: ATZ**
149 -
150 -(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
151 -|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
152 -|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
153 -|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
83 +(% border="0" style="background-color:#ffffcc; color:green; width:727.222px" %)
84 +|=(% colspan="3" %)ATZ: Trig a reset of the MCU
85 +|**Command Example**|**Function**|**Response**
86 +|ATZ|Reset MCU|(((
154 154  Device reset and show booting info
155 155  
156 156  LSN50 Device/LoRa ST Module
... ... @@ -164,30 +164,26 @@
164 164  <followed by the Tx and Rx information>
165 165  )))
166 166  
167 -(% style="color:blue" %)**Downlink Command: 0x04**
100 +{{info}}
101 +**Downlink Command: 0x04**
102 +{{/info}}
168 168  
169 -(((
170 170  Format: Command Code (0x04) followed by FF.
171 -)))
172 172  
173 -(((
174 174  If the downlink payload=**04FF**, the end node will reboot.
175 175  
176 -
177 -)))
178 -
179 179  == 4.3 Reset to factory Default ==
180 180  
181 -
182 182  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
183 183  
112 +{{info}}
113 +**AT Command: AT+FDR**
114 +{{/info}}
184 184  
185 -(% style="color:blue" %)**AT Command: AT+FDR**
186 -
187 -(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
188 -|=(% colspan="3" style="width: 786px;" %)Reset to factory default
189 -|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
190 -|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
116 +(% style="background-color:#ffffcc; color:green; width:831.222px" %)
117 +|=(% colspan="3" style="width: 828px;" %)Reset to factory default
118 +|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
119 +|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
191 191  Device reset to factory default parameters and show booting info
192 192  
193 193  LSN50 Device/LoRa ST Module
... ... @@ -201,59 +201,47 @@
201 201  Please set the parameters or reset Device to apply change
202 202  )))
203 203  
204 -(% style="color:blue" %)**Downlink Command: 0x04**
133 +{{info}}
134 +**Downlink Command: 0x04**
135 +{{/info}}
205 205  
206 -(((
207 207  Format: Command Code (0x04) followed by FE.
208 -)))
209 209  
210 -(((
211 211  If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
212 -)))
213 213  
214 214  
215 215  == 4.4 Show Firmware Version ==
216 216  
217 -
218 218  Feature: Show firmware version. No downlink command yet.
219 219  
146 +{{info}}
147 +**AT Command: AT+VER**
148 +{{/info}}
220 220  
221 -(% style="color:blue" %)**AT Command: AT+VER**
222 -
223 -(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
224 -|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
225 -|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
226 -|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
150 +(% style="background-color:#ffffcc; color:green" %)
151 +|=(% colspan="3" %)AT+VER: Image Version and Frequency Band
152 +|**Command Example**|**Function**|**Response**
153 +|AT+VER=?|Show Image version and Frequency Band|(((
227 227  1.3 EU868
228 228  
229 229  OK
230 230  )))
231 231  
232 -(% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
159 +{{info}}
160 +**Downlink Command: 0x26 (Valid in 006 stack)**
161 +{{/info}}
233 233  
234 -(((
235 235  Downlink Format: 0x26
236 -)))
237 237  
238 -(((
239 239  Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
240 -)))
241 241  
242 -(((
243 -
244 -
245 245  **xx: Software Type:**
246 -)))
247 247  
248 248  * 0x00 01: LGT92 Version
249 249  * 0x00 02: LBT1
250 250  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
251 251  
252 -(((
253 -
254 -
255 255  **yy: Frequency Band:**
256 -)))
257 257  
258 258  * 0x01: EU868
259 259  * 0x02: US915
... ... @@ -266,11 +266,7 @@
266 266  * 0x09: AS923-2
267 267  * 0xa0: AS923-3
268 268  
269 -(((
270 -
271 -
272 272  **zz: Subband**
273 -)))
274 274  
275 275  firmware version: v1.1.0 ~-~-> 110
276 276  
... ... @@ -277,13 +277,13 @@
277 277  
278 278  == 4.5 Show System Configure ==
279 279  
280 -
281 281  Feature: Show All configure. No downlink command yet.
282 282  
195 +{{info}}
196 +**AT Command: AT+CFG**
197 +{{/info}}
283 283  
284 -(% style="color:blue" %)**AT Command: AT+CFG**
285 -
286 -(% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
199 +(% style="background-color:#ffffcc; color:green; width:599.222px" %)
287 287  |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
288 288  |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
289 289  |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
... ... @@ -300,17 +300,18 @@
300 300  OK
301 301  )))
302 302  
216 +
303 303  = 5. Keys, IDs and EUIs management =
304 304  
305 305  == 5.1 Application EUI ==
306 306  
307 -
308 308  Feature: Get or Set the Application EUI.
309 309  
223 +{{info}}
224 +**AT Command: AT+APPEUI**
225 +{{/info}}
310 310  
311 -(% style="color:blue" %)**AT Command: AT+APPEUI**
312 -
313 -(% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
227 +(% style="background-color:#ffffcc; color:green; width:686.222px" %)
314 314  |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
315 315  |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
316 316  |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
... ... @@ -320,13 +320,13 @@
320 320  
321 321  == 5.2 Application Key ==
322 322  
323 -
324 324  Feature: Get or Set the Application Key.
325 325  
239 +{{info}}
240 +**AT Command: AT+APPKEY**
241 +{{/info}}
326 326  
327 -(% style="color:blue" %)**AT Command: AT+APPKEY**
328 -
329 -(% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
243 +(% style="background-color:#ffffcc; color:green; width:976.222px" %)
330 330  |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
331 331  |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
332 332  |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
... ... @@ -336,13 +336,13 @@
336 336  
337 337  == 5.3 Application Session Key ==
338 338  
339 -
340 340  Feature: Get or Set the Application Session Key.
341 341  
255 +{{info}}
256 +**AT Command: AT+APPSKEY**
257 +{{/info}}
342 342  
343 -(% style="color:blue" %)**AT Command: AT+APPSKEY**
344 -
345 -(% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
259 +(% style="background-color:#ffffcc; color:green; width:1040.22px" %)
346 346  |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
347 347  |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
348 348  |(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
... ... @@ -354,13 +354,13 @@
354 354  
355 355  == 5.4 Device Address ==
356 356  
357 -
358 358  Feature: Get or Set the Device Address.
359 359  
273 +{{info}}
274 +**AT Command: AT+DADDR**
275 +{{/info}}
360 360  
361 -(% style="color:blue" %)**AT Command: AT+DADDR**
362 -
363 -(% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
277 +(% style="background-color:#ffffcc; color:green; width:795.222px" %)
364 364  |=(% colspan="3" style="width: 792px;" %)AT+DADDR
365 365  |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
366 366  |(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
... ... @@ -372,13 +372,13 @@
372 372  
373 373  == 5.5 Device EUI ==
374 374  
375 -
376 376  Feature: Get or Set the Device EUI.
377 377  
291 +{{info}}
292 +**AT Command: AT+DEUI**
293 +{{/info}}
378 378  
379 -(% style="color:blue" %)**AT Command: AT+DEUI**
380 -
381 -(% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
295 +(% style="background-color:#ffffcc; color:green; width:1035.22px" %)
382 382  |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
383 383  |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
384 384  |(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
... ... @@ -390,13 +390,13 @@
390 390  
391 391  == 5.6 Network ID ==
392 392  
393 -
394 394  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
395 395  
309 +{{info}}
310 +**AT Command: AT+NWKID**
311 +{{/info}}
396 396  
397 -(% style="color:blue" %)**AT Command: AT+NWKID**
398 -
399 -(% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
313 +(% style="background-color:#ffffcc; color:green; width:448.222px" %)
400 400  |=(% colspan="3" style="width: 445px;" %)AT+NWKID
401 401  |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
402 402  |(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
... ... @@ -406,13 +406,13 @@
406 406  
407 407  == 5.7 Network Session Key ==
408 408  
409 -
410 410  Feature: Get or Set the Network Session Key
411 411  
325 +{{info}}
326 +**AT Command: AT+NWKSKEY**
327 +{{/info}}
412 412  
413 -(% style="color:blue" %)**AT Command: AT+NWKSKEY**
414 -
415 -(% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
329 +(% style="background-color:#ffffcc; color:green; width:1017.22px" %)
416 416  |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
417 417  |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
418 418  |(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
... ... @@ -424,15 +424,13 @@
424 424  
425 425  == 6.1 Confirm Mode ==
426 426  
427 -=== 6.1.1  AT+CFM command before DR-LWS007 software stack ===
428 -
429 -
430 430  Feature: Get or Set the confirmation mode (0-1).
431 431  
343 +{{info}}
344 +**AT Command: AT+CFM**
345 +{{/info}}
432 432  
433 -(% style="color:blue" %)**AT Command: AT+CFM**
434 -
435 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
347 +(% style="background-color:#ffffcc; color:green; width:710.222px" %)
436 436  |=(% colspan="3" style="width: 707px;" %)AT+CFM
437 437  |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
438 438  |(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
... ... @@ -441,87 +441,36 @@
441 441  |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
442 442  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
443 443  
444 -(% style="color:blue" %)**Downlink Command: 0x05**
356 +Downlink Command: 0x05
445 445  
446 446  Format: Command Code (0x05) followed by 2 bytes mode value.
447 447  
448 448  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
449 449  
450 -* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
451 -* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
362 +* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
363 +* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
452 452  
453 -=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
454 -
455 -
456 -(% style="color:blue" %)**AT Command: AT+CFM**
457 -
458 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
459 -|=(% colspan="3" style="width: 707px;" %)AT+CFM
460 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
461 -|(% style="width:160px" %)(((
462 -AT+CFM=1,0,0
463 -
464 -value1
465 -)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
466 -1
467 -
468 -OK
469 -)))
470 -|(% style="width:160px" %)(((
471 -AT+CFM=0,?,0
472 -
473 -value2
474 -)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
475 -0~~7
476 -
477 -OK
478 -)))
479 -|(% style="width:160px" %)(((
480 -AT+CFM=0,0,1
481 -
482 -value3
483 -)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
484 -1
485 -
486 -OK
487 -)))
488 -
489 -(% style="color:blue" %)**Downlink Command: 0x05**
490 -
491 -Format: Command Code (0x05) followed by 2 bytes mode value.
492 -
493 -If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
494 -
495 -* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
496 -* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
497 -
498 498  == 6.2 Confirm Status ==
499 499  
500 -
501 501  Feature: Get confirmation status of the last AT+SEND (0-1).
502 502  
369 +AT Command: AT+CFS
503 503  
504 -(% style="color:blue" %)**AT Command: AT+CFS**
505 -
506 -(% border="1" style="background-color:#ffffcc; color:green; width:463px" %)
507 -|=(% colspan="3" style="width: 460px;" %)AT+CFS
508 -|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:107px" %)**Response**
509 -|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:107px" %)0(((
371 +|=(% colspan="3" %)AT+CFS
372 +|**Command Example**|**Function**|**Response**
373 +|AT+CFS=?|Get confirmation status|0(((
510 510  OK
511 511  )))
512 512  
513 513  == 6.3 Join LoRa® Network ==
514 514  
515 -
516 516  Feature: Join network.
517 517  
381 +AT Command: AT+JOIN
518 518  
519 -(% style="color:blue" %)**AT Command: AT+JOIN**
520 -
521 -(% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
522 -|=(% colspan="3" style="width: 644px;" %)AT+JOIN
523 -|(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
524 -|(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
383 +|=(% colspan="3" %)AT+JOIN
384 +|**Command Example**|**Function**|**Response**
385 +|AT+JOIN ?|Get imformation.|AT+JOIN: Join network(((
525 525  OK
526 526  
527 527  While Error in format, return AT_BUSY_ERROR
... ... @@ -529,87 +529,72 @@
529 529  
530 530  == 6.4 LoRa® Network Join Mode ==
531 531  
532 -
533 533  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
534 534  
395 +AT Command: AT+NJM
535 535  
536 -(% style="color:blue" %)**AT Command: AT+NJM**
537 -
538 -(% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
539 -|=(% colspan="3" style="width: 750px;" %)AT+NJM
540 -|(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
541 -|(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
397 +|=(% colspan="3" %)AT+NJM
398 +|**Command Example**|**Function**|**Response**
399 +|AT+NJM=?|Get the Network Join Mode|1(((
542 542  OK
543 543  )))
544 -|(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
545 -|(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
402 +|AT+NJM=0|Set the Network Join Mode|OK
403 +|AT+NJM=2|Set the Network Join Mode|While Error in format, return AT_PARAM_ERROR
546 546  
547 -(% style="color:blue" %)**Downlink Command: 0x20**
405 +Downlink Command: 0x20
548 548  
549 549  Format: Command Code (0x20) followed by 1 bytes mode value.
550 550  
551 551  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
552 552  
553 -* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
554 -* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
411 +* Example 1: Downlink Payload: 2000 ~/~/ Set AT+NJM=O
412 +* Example 2: Downlink Payload: 2001 ~/~/ Set AT+NJM=1
555 555  
556 556  == 6.5 LoRa® Network Join Status ==
557 557  
558 -
559 559  Feature: LoRa® Network Join Status.
560 560  
418 +AT Command: AT+NJS
561 561  
562 -(% style="color:blue" %)**AT Command: AT+NJS**
563 -
564 -(% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
565 -|=(% colspan="3" style="width: 495px;" %)AT+NJS
566 -|(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
567 -|(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
420 +|=(% colspan="3" %)AT+NJS
421 +|**Command Example**|**Function**|**Response**
422 +|AT+NJS=?|Get the join status.|0(((
568 568  OK
569 569  )))
570 570  
571 571  == 6.6 Print Last Received Data in Raw Format ==
572 572  
573 -
574 574  Feature: Print Last Received Data in Raw Format<port:data>.
575 575  
430 +AT Command: AT+RECV
576 576  
577 -(% style="color:blue" %)**AT Command: AT+RECV**
578 -
579 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
580 -|=(% colspan="3" style="width: 584px;" %)AT+RECV
581 -|(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
582 -|(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
432 +|=(% colspan="3" %)AT+RECV
433 +|**Command Example**|**Function**|**Response**
434 +|AT+RECV=?|print last received data in raw format.|0:(((
583 583  OK
584 584  )))
585 585  
586 586  == 6.7 Print Last Received Data in Binary Format ==
587 587  
588 -
589 589  Feature: Print Last Received Data in Binary Format<port:data>.
590 590  
442 +AT Command: AT+RECVB
591 591  
592 -(% style="color:blue" %)**AT Command: AT+RECVB**
593 -
594 -(% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
595 -|=(% colspan="3" style="width: 790px;" %)AT+RECVB
596 -|(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
597 -|(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
444 +|=(% colspan="3" %)AT+RECVB
445 +|**Command Example**|**Function**|**Response**
446 +|AT+RECVB=?|print last received data in binary format (with hexadecimal values).|2: 0010(((
598 598  OK
599 599  )))
600 600  
601 601  == 6.8 Send Text Data ==
602 602  
603 -
604 604  Feature: Send Text Data<port:data>.
605 605  
454 +AT Command: AT+SEND
606 606  
607 -(% style="color:blue" %)**AT Command: AT+SEND**
608 -
609 -(% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
610 -|=(% colspan="3" style="width: 988px;" %)AT+SEND
611 -|(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
612 -|(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
456 +|=(% colspan="3" %)AT+SEND
457 +|**Command Example**|**Function**|**Response**
458 +|AT+SEND=12:hello world|Send text data along with the application port.|OK(((
613 613  While Error in format, return
614 614  
615 615  AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
... ... @@ -619,17 +619,14 @@
619 619  
620 620  == 6.9 Send Hexadecimal Data ==
621 621  
622 -
623 623  Feature: Send hexadecimal data along with the application port.
624 624  
470 +AT Command: AT+SENDB
625 625  
626 -(% style="color:blue" %)**AT Command: AT+SENDB**
627 -
628 -(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
629 -|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
630 -|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
631 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
632 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
472 +|=(% colspan="3" %)AT+SENDB
473 +|**Command Example**|**Function**|**Response**
474 +|AT+SENDB=12:abcdef0123456789|Send hexadecimal data along with the application port.|OK
475 +|AT+SENDB=abcdef0123456789|Send hexadecimal data along with the application port.|While Error in format, return(((
633 633  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
634 634  
635 635  
... ... @@ -639,112 +639,97 @@
639 639  
640 640  == 7.1 Adaptive Data Rate ==
641 641  
642 -
643 643  Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
644 644  
645 645  
646 -(% style="color:blue" %)**AT Command: AT+ADR**
488 +AT Command: AT+ADR
647 647  
648 -(% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
649 -|=(% colspan="3" style="width: 680px;" %)AT+ADR
650 -|(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
651 -|(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1(((
490 +|=(% colspan="3" %)AT+ADR
491 +|**Command Example**|**Function**|**Response**
492 +|AT+ADR=?|Get the Adaptive Data Rate setting.|1(((
652 652  OK
653 653  )))
654 -|(% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)OK
655 -|(% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)While Error in format, return(((
495 +|AT+ADR=0|Set the Adaptive Data Rate setting.|OK
496 +|AT+ADR=2|Set the Adaptive Data Rate setting.|While Error in format, return(((
656 656  AT_PARAM_ERROR
657 657  )))
658 658  
659 -(% style="color:blue" %)**Downlink Command: 0x22**
500 +Downlink Command: 0x22
660 660  
502 +
661 661  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
662 662  
663 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
664 -* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
505 +* Example 1: Downlink Payload: 2201 ~/~/ Set AT+ADR=1.
506 +* Example 2: Downlink Payload: 2200FFFF ~/~/ Set AT+ADR=0.
665 665  
666 666  == 7.2 LoRa® Class ==
667 667  
668 -
669 669  Feature: Get or Set the Device Class(Currently only support class A, class C).
670 670  
512 +AT Command:AT+CLASS
671 671  
672 -(% style="color:blue" %)**AT Command:  AT+CLASS**
673 -
674 -(% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
675 -|=(% colspan="3" style="width: 504px;" %)AT+CLASS
676 -|(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
677 -|(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
514 +|=(% colspan="3" %)AT+CLASS
515 +|**Command Example**|**Function**|**Response**
516 +|AT+CLASS=?|Get the Device Class.|A(((
678 678  OK
679 679  )))
680 -|(% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((
519 +|AT+CLASS=C|Set the Device Class.|OK(((
681 681  
682 682  )))
683 683  
684 684  == 7.3 Duty Cycle Setting ==
685 685  
525 +Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
686 686  
687 -Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
527 +AT Command:AT+DCS
688 688  
689 -
690 -(% style="color:blue" %)**AT Command:  AT+DCS**
691 -
692 -(% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
693 -|=(% colspan="3" style="width: 512px;" %)AT+DCS
694 -|(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
695 -|(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
529 +|=(% colspan="3" %)AT+DCS
530 +|**Command Example**|**Function**|**Response**
531 +|AT+DCS=?|Get the ETSI Duty Cycle setting.|1(((
696 696  OK
697 697  )))
698 -|(% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((
534 +|AT+DCS=1|Set the ETSI Duty Cycle setting.|OK(((
699 699  
700 700  )))
701 701  
702 702  == 7.4 Data Rate ==
703 703  
540 +Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
704 704  
705 -Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) .
542 +AT Command: AT+DR
706 706  
707 -(% style="color:red" %)
708 -**Notice:**
709 -
710 -* User need to set Adaptive Data Rate(ADR)=0 first. otherwise device will respond to server's ADR command and change the DR according to server auto-adjustment.
711 -* Data Rate specifies Spreading Factor. The mapping varies in different frequency bands. User can check this link for detail. [[rp2-1.0.3-lorawan-regional-parameters.pdf>>https://lora-alliance.org/resource_hub/rp2-1-0-3-lorawan-regional-parameters/]]
712 -
713 -(% style="color:blue" %)**AT Command: AT+DR**
714 -
715 -(% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
716 -|=(% colspan="3" style="width: 463px;" %)AT+DR
717 -|(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
718 -|(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
544 +|=(% colspan="3" %)AT+DR
545 +|**Command Example**|**Function**|**Response**
546 +|AT+DR=?|Get the Data Rate.|5(((
719 719  OK
720 720  )))
721 -|(% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((
549 +|AT+DR=2|Set the Data Rate.|OK(((
722 722  
723 723  )))
724 724  
725 -(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
553 +Downlink Command: 0x2200aaFF
726 726  
555 +
727 727  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
728 728  
729 -* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
730 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
558 +* Example 1: Downlink Payload: 220001FF ~/~/ Set AT+DR=1.
559 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+DR=0.
731 731  
732 732  == 7.5 Frame Counter Downlink ==
733 733  
734 -
735 735  Feature: Get or Set the Frame Counter Downlink.
736 736  
565 +AT Command:AT+FCD
737 737  
738 -(% style="color:blue" %)**AT Command:  AT+FCD**
739 -
740 -(% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
741 -|=(% colspan="3" style="width: 690px;" %)AT+FCD
742 -|(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
743 -|(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
567 +|=(% colspan="3" %)AT+FCD
568 +|**Command Example**|**Function**|**Response**
569 +|AT+FCD=?|Get the Frame Counter Downlink.|0(((
744 744  OK
745 745  )))
746 -|(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
572 +|AT+FCD=10|Set the Frame Counter Downlink.|(System will write new value to FCD)(((
747 747  OK
574 +
575 +
748 748  )))
749 749  
750 750  == 7.6 Frame Counter Uplink ==
... ... @@ -751,171 +751,136 @@
751 751  
752 752  Feature: Get or Set the Frame Counter Uplink.
753 753  
582 +AT Command:AT+FCU
754 754  
755 -(% style="color:blue" %)**AT Command:  AT+FCU**
756 -
757 -(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
758 -|=(% colspan="3" style="width: 531px;" %)AT+FCU
759 -|(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
760 -|(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
584 +|=(% colspan="3" %)AT+FCU
585 +|**Command Example**|**Function**|**Response**
586 +|AT+FCU=?|Get the Frame Counter Uplink.|0(((
761 761  OK
762 762  )))
763 -|(% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((
589 +|AT+FCU=10|Set the Frame Counter Uplink.|OK(((
764 764  
765 765  )))
766 766  
767 767  == 7.7 Join Accept Delay1 ==
768 768  
769 -
770 770  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
771 771  
597 +AT Command:AT+JN1DL
772 772  
773 -(% style="color:blue" %)**AT Command:  AT+JN1DL**
774 -
775 -(% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
776 -|=(% colspan="3" style="width: 534px;" %)AT+JN1DL
777 -|(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
778 -|(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
599 +|=(% colspan="3" %)AT+JN1DL
600 +|**Command Example**|**Function**|**Response**
601 +|AT+JN1DL=?|Get the Join Accept Delay.|5000(((
779 779  OK
780 780  )))
781 -|(% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((
604 +|AT+JN1DL=10000|Set the Join Accept Delay.|OK(((
782 782  
783 783  )))
784 784  
785 785  == 7.8 Join Accept Delay2 ==
786 786  
787 -
788 788  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
789 789  
612 +AT Command:AT+JN2DL
790 790  
791 -(% style="color:blue" %)**AT Command:  AT+JN2DL**
792 -
793 -(% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
794 -|=(% colspan="3" style="width: 535px;" %)AT+JN2DL
795 -|(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
796 -|(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
614 +|=(% colspan="3" %)AT+JN2DL
615 +|**Command Example**|**Function**|**Response**
616 +|AT+JN2DL=?|Get the Join Accept Delay.|6000(((
797 797  OK
798 798  )))
799 -|(% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((
619 +|AT+JN2DL=20000|Set the Join Accept Delay.|OK(((
800 800  
801 801  )))
802 802  
803 803  == 7.9 Public Network Mode ==
804 804  
625 +Feature: Get or Set the public network mode. (0: off, 1: on)
805 805  
806 -Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
627 +AT Command:AT+PNM
807 807  
808 -(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
809 -
810 -
811 -(% style="color:blue" %)**AT Command:  AT+PNM**
812 -
813 -(% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
814 -|=(% colspan="3" style="width: 664px;" %)AT+PNM
815 -|(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
816 -|(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
629 +|=(% colspan="3" %)AT+PNM
630 +|**Command Example**|**Function**|**Response**
631 +|AT+PNM=?|Get the public network mode.|1(((
817 817  OK
818 818  )))
819 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
820 -Set the public network mode.
821 -
822 -Set syncword=0x34
823 -)))|(% style="width:272px" %)(System will write new value to PNM)(((
634 +|AT+PNM=1|Set the public network mode.|(System will write new value to PNM)(((
824 824  OK
825 825  
826 826  
827 827  )))
828 -|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
829 829  
830 830  == 7.10 Receive Delay1 ==
831 831  
832 -
833 833  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
834 834  
644 +AT Command:AT+RX1DL
835 835  
836 -(% style="color:blue" %)**AT Command: AT+RX1DL**
837 -
838 -(% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
839 -|=(% colspan="3" style="width: 405px;" %)AT+RX1DL
840 -|(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
841 -|(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
646 +|=(% colspan="3" %)AT+RX1DL
647 +|**Command Example**|**Function**|**Response**
648 +|AT+RX1DL=?|Get the delay.|1000(((
842 842  OK
843 843  )))
844 -|(% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((
651 +|AT+RX1DL=1500|Set the delay.|OK(((
845 845  
846 846  )))
847 847  
848 -== 7.11 Receive Delay2 ==
655 +== 7.11Receive Delay2 ==
849 849  
850 -
851 851  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
852 852  
659 +AT Command:AT+RX2DL
853 853  
854 -(% style="color:blue" %)**AT Command: AT+RX2DL**
855 -
856 -(% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
857 -|=(% colspan="3" style="width: 478px;" %)AT+RX2DL
858 -|(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
859 -|(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
661 +|=(% colspan="3" %)AT+RX2DL
662 +|**Command Example**|**Function**|**Response**
663 +|AT+RX2DL=?|Get the delay.|2000(((
860 860  OK
861 861  )))
862 -|(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
666 +|AT+RX2DL=2500|Set the delay.|OK(((
863 863  
864 864  )))
865 865  
866 866  == 7.12 Rx2 Window Data Rate ==
867 867  
868 -
869 869  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
870 870  
674 +AT Command:AT+RX2DR
871 871  
872 -(% style="color:blue" %)**AT Command:  AT+RX2DR**
873 -
874 -(% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
875 -|=(% colspan="3" style="width: 522px;" %)AT+RX2DR
876 -|(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
877 -|(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
676 +|=(% colspan="3" %)AT+RX2DR
677 +|**Command Example**|**Function**|**Response**
678 +|AT+RX2DR=?|Get the Rx2 window data rate.|2(((
878 878  OK
879 879  )))
880 -|(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
681 +|AT+RX2DR=6|Set the Rx2 window data rate.|OK(((
881 881  
882 882  )))
883 883  
884 884  == 7.13 Rx2 Window Frequency ==
885 885  
886 -
887 887  Feature: Get or Set the Rx2 window frequency
888 888  
689 +AT Command:AT+RX2FQ
889 889  
890 -(% style="color:blue" %)**AT Command:  AT+RX2FQ**
891 -
892 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
893 -|=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
894 -|(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
895 -|(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
691 +|=(% colspan="3" %)AT+RX2FQ
692 +|**Command Example**|**Function**|**Response**
693 +|AT+RX2FQ=?|Get the Rx2 window frequency.|434665000(((
896 896  OK
897 897  )))
898 -|(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
696 +|AT+RX2FQ=434665000|Set the Rx2 window frequency.|OK(((
899 899  
900 900  )))
901 901  
902 902  == 7.14 Transmit Power ==
903 903  
904 -
905 905  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
906 906  
907 -(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
704 +AT Command:AT+TXP
908 908  
909 -
910 -(% style="color:blue" %)**AT Command:  AT+TXP**
911 -
912 -(% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
913 -|=(% colspan="3" style="width: 462px;" %)AT+TXP
914 -|(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
915 -|(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
706 +|=(% colspan="3" %)AT+TXP
707 +|**Command Example**|**Function**|**Response**
708 +|AT+TXP=?|Get the Transmit Power.|0(((
916 916  OK
917 917  )))
918 -|(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
711 +|AT+TXP=1|Set the Transmit Power.|OK(((
919 919  
920 920  )))
921 921  
... ... @@ -923,364 +923,195 @@
923 923  
924 924  If the downlink payload=22000100, it means setting the TXP to 0.
925 925  
926 -* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
927 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
719 +* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2.
720 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0.
928 928  
929 929  == 7.15 RSSI of the Last Received Packet ==
930 930  
931 -
932 932  Feature: Get or Set the Rx2 window frequency
933 933  
726 +AT Command:AT+RSSI
934 934  
935 -(% style="color:blue" %)**AT Command:AT+RSSI**
936 -
937 -(% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
938 -|=(% colspan="3" style="width: 554px;" %)AT+RSSI
939 -|(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
940 -|(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
728 +|=(% colspan="3" %)AT+RSSI
729 +|**Command Example**|**Function**|**Response**
730 +|AT+RSSI=?|Get the RSSI of the last received packet.|0(((
941 941  OK
942 942  )))
943 943  
944 944  == 7.16 SNR of the Last Received Packet ==
945 945  
946 -
947 947  Feature: Get the SNR of the last received packet
948 948  
738 +AT Command:AT+SNR
949 949  
950 -(% style="color:blue" %)**AT Command:  AT+SNR**
951 -
952 -(% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
953 -|=(% colspan="3" style="width: 568px;" %)AT+SNR
954 -|(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
955 -|(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
740 +|=(% colspan="3" %)AT+SNR
741 +|**Command Example**|**Function**|**Response**
742 +|AT+SNR=?|Get the RSSI of the last received packet.|0(((
956 956  OK
957 957  )))
958 958  
959 959  == 7.17 Application Port ==
960 960  
961 -
962 962  Feature: Get or set the application port.
963 963  
750 +AT Command: AT+PORT
964 964  
965 -(% style="color:blue" %)**AT Command: AT+PORT**
966 -
967 -(% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
968 -|=(% colspan="3" style="width: 497px;" %)AT+PORT
969 -|(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
970 -|(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
752 +|=(% colspan="3" %)AT+PORT
753 +|**Command Example**|**Function**|**Response**
754 +|AT+PORT=?|Get the application port|21(((
971 971  OK
972 972  )))
973 -|(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
757 +|AT+PORT=21|Set the application port|OK
974 974  
975 -(% style="color:blue" %)**Downlink Command: 0x23**
759 +Downlink Command: 0x23
976 976  
977 977  Format: Command Code (0x23) followed by 1 bytes port value.
978 978  
979 979  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
980 980  
981 -* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
982 -* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
765 +* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1
766 +* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5
983 983  
984 984  == 7.18 Single Channel Mode ==
985 985  
986 -
987 987  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
988 988  
772 +AT Command: AT+CHS
989 989  
990 -(% style="color:blue" %)**AT Command: AT+CHS**
991 -
992 -(% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
993 -|=(% colspan="3" style="width: 600px;" %)AT+CHS
994 -|(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
995 -|(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
774 +|=(% colspan="3" %)AT+CHS
775 +|**Command Example**|**Function**|**Response**
776 +|AT+CHS=?|Get Frequency for Single Channel Mode|0(((
996 996  OK
997 997  )))
998 -|(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
779 +|AT+CHS=868100000|Set Frequency for Single Channel Mode|OK
999 999  
1000 1000  == 7.19 Eight Channel Mode ==
1001 1001  
1002 -
1003 1003  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1004 1004  
785 +AT Command: AT+CHE
1005 1005  
1006 -(% style="color:blue" %)**AT Command: AT+CHE**
1007 -
1008 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1009 -|=(% colspan="3" style="width: 707px;" %)AT+CHE
1010 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1011 -|(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
787 +|=(% colspan="3" %)AT+CHE
788 +|**Command Example**|**Function**|**Response**
789 +|AT+CHE=?|Get eight channels mode|1(((
1012 1012  902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
1013 1013  
1014 1014  OK
1015 1015  )))
1016 -|(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
794 +|AT+CHE=1|Set eight channels mode|OK
1017 1017  
1018 -(% style="color:blue" %)**Downlink Command: 0x24 (LHT65,LHT65N Downlink Command:0x07)**
796 +Downlink Command: 0x24
1019 1019  
1020 1020  Format: Command Code (0x24) followed by 1 bytes channel value.
1021 1021  
1022 1022  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1023 1023  
1024 -* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1025 -* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
802 +* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1
803 +* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5
1026 1026  
1027 1027  == 7.20 Get or Set RXwindows1 timeout ==
1028 1028  
807 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1029 1029  
1030 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
809 +AT Command: AT+RX1WTO
1031 1031  
1032 -
1033 -(% style="color:blue" %)**AT Command: AT+RX1WTO**
1034 -
1035 -(% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1036 -|=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1037 -|(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
1038 -|(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
811 +|=(% colspan="3" %)AT+ RX1WTO
812 +|**Command Example**|**Function**|**Response**
813 +|AT+RX1WTO=?|Get RXwindows1 timeout|14(((
1039 1039  OK
1040 1040  )))
1041 -|(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
816 +|AT+RX1WTO=60|Set RXwindows1 timeout|OK
1042 1042  
1043 -(((
1044 -
818 +AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1045 1045  
820 +[[~[~[image:https://wiki.dragino.com/images/thumb/5/51/RX1WTO.JPG/600px-RX1WTO.JPG~|~|alt="RX1WTO.JPG" height="239" width="600"~]~]>>url:https://wiki.dragino.com/index.php/File:RX1WTO.JPG]]
1046 1046  
1047 -(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1048 -
1049 -
1050 -)))
1051 -
1052 -[[image:image-20220526162535-1.png]]
1053 -
1054 -
1055 -(((
1056 1056  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1057 1057  
1058 -
1059 -)))
1060 -
1061 1061  == 7.21 Get or Set RXwindows2 timeout ==
1062 1062  
826 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1063 1063  
1064 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
828 +AT Command: AT+RX2WTO
1065 1065  
1066 -
1067 -(% style="color:blue" %)**AT Command: AT+RX2WTO**
1068 -
1069 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1070 -|=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1071 -|(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
1072 -|(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
830 +|=(% colspan="3" %)AT+ RX2WTO
831 +|**Command Example**|**Function**|**Response**
832 +|AT+RX2WTO=?|Get RXwindows2 timeout|7(((
1073 1073  OK
1074 1074  )))
1075 -|(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
835 +|AT+RX2WTO=20|Set RXwindows2 timeout|OK
1076 1076  
1077 1077  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1078 1078  
1079 -
1080 1080  Feature: Get or Set uplinkdwelltime
1081 1081  
841 +AT Command: AT+DWELLT
1082 1082  
1083 -(% style="color:blue" %)**AT Command: AT+DWELLT**
1084 -
1085 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1086 -|=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1087 -|(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
1088 -|(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
843 +|=(% colspan="3" %)AT+DWELLT
844 +|**Command Example**|**Function**|**Response**
845 +|AT+DWELLT=?|Get uplinkdwelltime|1(((
1089 1089  OK
1090 1090  )))
1091 -|(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
848 +|AT+DWELLT=0|Set uplinkdwelltime|OK
1092 1092  
1093 -(% style="color:blue" %)**Downlink Command: 0x25**
850 +Downlink Command: 0x25
1094 1094  
1095 1095  Format: Command Code (0x25) followed by 1 bytes state value.
1096 1096  
1097 1097  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1098 1098  
1099 -* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1100 -* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
856 +* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1
857 +* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0
1101 1101  
1102 1102  == 7.23 Set Packet Receiving Response Level ==
1103 1103  
1104 -
1105 1105  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1106 1106  
863 +RPL value:
1107 1107  
1108 -**RPL value:**
865 +* AT+RPL=0: Device won't immediately reply any downlink commands from platform.
866 +* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
867 +* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
868 +* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
869 +* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1109 1109  
1110 -* **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1111 -* **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1112 -* **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1113 -* **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1114 -* **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
871 +Case Analyes:
1115 1115  
1116 -**Case Analyes:**
1117 -
1118 1118  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1119 1119  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1120 1120  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1121 1121  
1122 -(% style="color:blue" %)**AT Command: AT+RPL**
877 +AT Command: AT+RPL
1123 1123  
1124 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1125 -|=(% colspan="3" style="width: 533px;" %)AT+RPL
1126 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1127 -|(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
879 +|=(% colspan="3" %)AT+RPL
880 +|**Command Example**|**Function**|**Response**
881 +|AT+RPL=?|Get packet receiving response level|1(((
1128 1128  OK
1129 1129  )))
1130 -|(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
884 +|AT+RPL=0|Set packet receiving response level|OK
1131 1131  
1132 -(% style="color:blue" %)**Downlink Command: 0x21**
886 +Downlink Command: 0x21
1133 1133  
1134 1134  Format: Command Code (0x21) followed by 1 bytes level value.
1135 1135  
1136 1136  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1137 1137  
1138 -* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1139 -* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
892 +* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1
893 +* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2
1140 1140  
1141 -== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1142 -
1143 -
1144 -(% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1145 -
1146 -(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1147 -|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1148 -|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1149 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1150 -OK
1151 -)))
1152 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1153 -value2: 0: uplink fcnt doesn't change for each NBTrans;
1154 -
1155 -1: uplink fcnt increase by 1 for each NBTrans.
1156 -)))|(% style="width:87px" %)(((
1157 -1
1158 -
1159 -OK
1160 -)))
1161 -
1162 -(% style="color:blue" %)**Downlink Command: 0x33**
1163 -
1164 -Format: Command Code (0x33) followed by 2 bytes mode value.
1165 -
1166 -If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1167 -
1168 -* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1169 -* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1170 -
1171 -== 7.25 Device offline rejoining （LWS007) ==
1172 -
1173 -
1174 -(% style="color:blue" %)**AT Command: AT+DDETECT**
1175 -
1176 -AT+DDETECT=<Flag>,<ACK_Timout_1>,<ACK_Timout_2> (Default Value: AT+DDETECT=1,1440,2880)
1177 -
1178 -* ACK_Timout_1: Unit: min
1179 -* ACK_Timout_2: Unit: min
1180 -
1181 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1182 -|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1183 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1184 -|(% style="width:160px" %)(((
1185 -AT+DDETECT=1,1440,2880
1186 -
1187 -value1
1188 -)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1189 -1
1190 -
1191 -OK
1192 -)))
1193 -|(% style="width:160px" %)(((
1194 -AT+DDETECT=1,?,2880
1195 -
1196 -value2
1197 -)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1198 -
1199 -
1200 -OK
1201 -)))
1202 -|(% style="width:160px" %)(((
1203 -AT+DDETECT=1,1440,？
1204 -
1205 -value3
1206 -)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1207 -
1208 -
1209 -OK
1210 -)))
1211 -
1212 -(% style="color:blue" %)**Downlink Command: 0x32**
1213 -
1214 -Format: Command Code (0x32) followed by 2 bytes mode value.
1215 -
1216 -If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 32.
1217 -
1218 -* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1219 -** 0x01 : Flag
1220 -** 0x05A0: ACK_Timout_1 : 1440minutes (24 hours)
1221 -** 0x0B40: ACK_Timout_2 : 2880minutes (48 hours)
1222 -** **Explain**: Enable Online Detect, if end node doesn't receive any downlink within ACK_Timout_1( 1440 minutes or 24 hours). End node will use confirmed uplink to send packets during ACK_Timout_1 (the 24th hour) to ACK_Timout_2 ( the 48th hour). If from the 24th to 48th hour, end node got an downlink from server, it will switch back to unconfirmed uplink. end node will restart ACK_Timout_1. If from the 24th to 48th hour, end node still not got any downlink, means device doesn't get ACK from server within last 48 hours. Device will process rejoin, rejoin request interval is AT+RJTDC period. For AU915/ US915, device will use the sub-band used for last join.
1223 -
1224 -== 7.26 Request the server to send an ACK ==
1225 -
1226 -
1227 -(% style="color:blue" %)**AT Command: AT+PNACKMD**
1228 -
1229 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1230 -|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1231 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1232 -|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1233 -OK
1234 -)))
1235 -|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1236 -0
1237 -
1238 -OK
1239 -)))
1240 -
1241 -== 7.27 Adjust network rejoining interval ==
1242 -
1243 -
1244 -(% style="color:blue" %)**AT Command: AT+RJTDC**
1245 -
1246 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1247 -|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1248 -|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1249 -|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30(((
1250 -OK
1251 -
1252 -the interval is 30 min
1253 -)))
1254 -|(% style="width:165px" %)AT+RJTDC=60|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1255 -Set the ReJoin data transmission interval to 60 min
1256 -)))
1257 -
1258 -(% style="color:blue" %)**Downlink Command: 0x26**
1259 -
1260 -Format: Command Code (0x26) followed by 2 bytes mode value.
1261 -
1262 -If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1263 -
1264 -* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1265 -* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1266 -
1267 1267  = 8. AT Commands Combination =
1268 1268  
1269 1269  == 8.1 Set a fix RX2DR for downlink window ==
1270 1270  
899 +* AT+ADR=0 ~-~-> Disable ADR first
900 +* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate
1271 1271  
1272 -* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1273 -* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1274 -
1275 1275  == 8.2 Use Downlink Command to set a fix uplink DR ==
1276 1276  
904 +Downlink Command: 0x22000500
1277 1277  
1278 -(% style="color:blue" %)**Downlink Command: 0x22000500**
906 +Same as:
1279 1279  
1280 -**Same as:**
1281 -
1282 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1283 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1284 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1285 -
1286 -
908 +* AT+ADR=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Adaptive_Data_Rate]]
909 +* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]]
910 +* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]
image-20220511120050-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -136.3 KB
Content
image-20220526162535-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -149.4 KB
Content

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0