Changes for page End Device AT Commands and Downlink Command

Last modified by kai on 2024/09/06 10:00

From version < 60.1 >

edited by Edwin Chen
on 2023/03/25 15:30

To version < 58.2 >

edited by Xiaoling
on 2022/12/02 13:45

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Edwin
++XWiki.Xiaoling

Content

@@ -28,6 +28,7 @@
  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
++
  = 3. Support End Node and firmware version =
@@ -140,7 +140,6 @@
  * **Example 1**: Downlink Payload:** 0100001E**               ~/~/ Set Transmit Interval (TDC) = 30 seconds
  * **Example 2**: Downlink Payload:** 0100003C**               ~/~/ Set Transmit Interval (TDC) = 60 seconds
--
  == 4.2 Reboot End Node ==
@@ -175,6 +175,7 @@
  (((
  If the downlink payload=**04FF**, the end node will reboot.
++
  )))
@@ -214,6 +214,7 @@
  )))
++
  == 4.4 Show Firmware Version ==
@@ -244,6 +244,7 @@
  (((
++
  **xx: Software Type:**
  )))
@@ -277,6 +277,7 @@
  firmware version: v1.1.0 ~-~-> 110
++
  == 4.5 Show System Configure ==
@@ -302,7 +302,6 @@
  OK
  )))
--
  = 5. Keys, IDs and EUIs management =
  == 5.1 Application EUI ==
@@ -321,7 +321,6 @@
  )))
  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
--
  == 5.2 Application Key ==
@@ -338,7 +338,6 @@
  )))
  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
--
  == 5.3 Application Session Key ==
@@ -357,7 +357,6 @@
  OK
  )))
--
  == 5.4 Device Address ==
@@ -376,7 +376,6 @@
  )))
  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
--
  == 5.5 Device EUI ==
@@ -395,7 +395,6 @@
  OK
  )))
--
  == 5.6 Network ID ==
@@ -412,7 +412,6 @@
  )))
  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
--
  == 5.7 Network Session Key ==
@@ -429,7 +429,6 @@
  )))
  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
--
  = 6. Joining and sending date on LoRaWAN network =
  == 6.1 Confirm Mode ==
@@ -460,7 +460,6 @@
  * **Example 1:** Downlink Payload: 0501            ~/~/ Set AT+CFM=1
  * **Example 2:** Downlink Payload: 0500            ~/~/ Set AT+CFM=0
--
  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
@@ -506,7 +506,6 @@
  * **Example 1:** Downlink Payload: 05010101           ~/~/ Set AT+CFM=1,1,1
  * **Example 2:** Downlink Payload: 05000700           ~/~/ Set AT+CFM=0,7,0
--
  == 6.2 Confirm Status ==
@@ -515,14 +515,13 @@
  (% style="color:blue" %)**AT Command: AT+CFS**
--(% border="1" style="background-color:#ffffcc; color:green; width:463px" %)
--|=(% colspan="3" style="width: 460px;" %)AT+CFS
--|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:107px" %)**Response**
--|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:107px" %)0(((
++(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
++|=(% colspan="3" style="width: 531px;" %)AT+CFS
++|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
++|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
  OK
  )))
--
  == 6.3 Join LoRa® Network ==
@@ -540,7 +540,6 @@
  While Error in format, return AT_BUSY_ERROR
  )))
--
  == 6.4 LoRa® Network Join Mode ==
@@ -567,7 +567,6 @@
  * **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
  * **Example 2:** Downlink Payload: **2001**                   ~/~/ Set AT+NJM=1
--
  == 6.5 LoRa® Network Join Status ==
@@ -583,7 +583,6 @@
  OK
  )))
--
  == 6.6 Print Last Received Data in Raw Format ==
@@ -599,7 +599,6 @@
  OK
  )))
--
  == 6.7 Print Last Received Data in Binary Format ==
@@ -615,7 +615,6 @@
  OK
  )))
--
  == 6.8 Send Text Data ==
@@ -635,7 +635,6 @@
  )))
--
  == 6.9 Send Hexadecimal Data ==
@@ -654,7 +654,6 @@
  )))
--
  = 7. LoRaWAN network management =
  == 7.1 Adaptive Data Rate ==
@@ -683,7 +683,6 @@
  * **Example 1**: Downlink Payload: **2201**                       ~/~/ Set AT+ADR=1.
  * **Example 2**: Downlink Payload: **2200FFFF**               ~/~/ Set AT+ADR=0.
--
  == 7.2 LoRa® Class ==
@@ -702,7 +702,6 @@
  )))
--
  == 7.3 Duty Cycle Setting ==
@@ -721,7 +721,6 @@
  )))
--
  == 7.4 Data Rate ==
@@ -752,7 +752,6 @@
  * **Example 1**: Downlink Payload: **220001FF**                     ~/~/ Set AT+DR=1.
  * **Example 2**: Downlink Payload: **220000FF**                     ~/~/ Set AT+DR=0.
--
  == 7.5 Frame Counter Downlink ==
@@ -771,7 +771,6 @@
  OK
  )))
--
  == 7.6 Frame Counter Uplink ==
  Feature: Get or Set the Frame Counter Uplink.
@@ -789,7 +789,6 @@
  )))
--
  == 7.7 Join Accept Delay1 ==
@@ -808,7 +808,6 @@
  )))
--
  == 7.8 Join Accept Delay2 ==
@@ -827,7 +827,6 @@
  )))
--
  == 7.9 Public Network Mode ==
@@ -855,7 +855,6 @@
  )))
  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
--
  == 7.10 Receive Delay1 ==
@@ -874,7 +874,6 @@
  )))
--
  == 7.11 Receive Delay2 ==
@@ -893,7 +893,6 @@
  )))
--
  == 7.12 Rx2 Window Data Rate ==
@@ -912,7 +912,6 @@
  )))
--
  == 7.13 Rx2 Window Frequency ==
@@ -931,7 +931,6 @@
  )))
--
  == 7.14 Transmit Power ==
@@ -959,7 +959,6 @@
  * **Example 1**: Downlink Payload: **22000102**         ~/~/ Set AT+TXP=2.
  * **Example 2**: Downlink Payload: **220000FF**         ~/~/ Set AT+TXP=0.
--
  == 7.15 RSSI of the Last Received Packet ==
@@ -975,7 +975,6 @@
  OK
  )))
--
  == 7.16 SNR of the Last Received Packet ==
@@ -991,7 +991,6 @@
  OK
  )))
--
  == 7.17 Application Port ==
@@ -1017,7 +1017,6 @@
  * **Example 1**: Downlink Payload: **2301**          ~/~/ set the application port to 1
  * **Example 2**: Downlink Payload:** 2305**          ~/~/ set the application port to 5
--
  == 7.18 Single Channel Mode ==
@@ -1034,7 +1034,6 @@
  )))
  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
--
  == 7.19 Eight Channel Mode ==
@@ -1062,7 +1062,6 @@
  * **Example 1**: Downlink Payload: 2401           ~/~/ set channel mode to 1
  * **Example 2**: Downlink Payload: 2405           ~/~/ set channel mode to 5
--
  == 7.20 Get or Set RXwindows1 timeout ==
@@ -1094,6 +1094,7 @@
  (((
  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
++
  )))
@@ -1113,7 +1113,6 @@
  )))
  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
--
  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
@@ -1139,7 +1139,6 @@
  * **Example 1**: Downlink Payload: **2501**                    ~/~/ set uplinkdwelltime to 1
  * **Example 2**: Downlink Payload: **2500**                    ~/~/ set uplinkdwelltime to 0
--
  == 7.23 Set Packet Receiving Response Level ==
@@ -1179,7 +1179,6 @@
  * **Example 1**: Downlink Payload: **2101**                ~/~/ set packet receiving response level to 1
  * **Example 2**: Downlink Payload: **2102**                ~/~/ set packet receiving response level to 2
--
  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
@@ -1210,17 +1210,11 @@
  * Example 1: Downlink Payload: 330100                 ~/~/ Set AT+SETMAXNBTRANS=1,0
  * Example 2: Downlink Payload: 330201                 ~/~/ Set AT+SETMAXNBTRANS=2,1
--
  == 7.25 Device offline rejoining （LWS007) ==
  (% style="color:blue" %)**AT Command: AT+DDETECT**
--AT+DDETECT=<Flag>,<ACK_Timout_1>,<ACK_Timout_2> (Default Value: AT+DDETECT=1,1440,2880)
--
--* ACK_Timout_1: Unit: min
--* ACK_Timout_2: Unit: min
--
  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
  |=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
  |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
@@ -1252,19 +1252,14 @@
  OK
  )))
--(% style="color:blue" %)**Downlink Command: 0x32**
++(% style="color:blue" %)**Downlink Command: 0x33**
  Format: Command Code (0x32) followed by 2 bytes mode value.
--If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 32.
++If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
--* **Example 1:** Downlink Payload: 320105A00B40                     ~/~/ Set AT+DDETECT=1,1440,2880
--** 0x01 : Flag
--** 0x05A0: ACK_Timout_1 : 1440minutes (24 hours)
--** 0x0B40: ACK_Timout_2 : 2880minutes (48 hours)
--** **Explain**: Enable Online Detect, if end node doesn't receive any downlink within ACK_Timout_1( 1440 minutes or 24 hours). End node will use confirmed uplink to send packets during ACK_Timout_1 (the 24th hour) to ACK_Timout_2 ( the 48th hour). If from the 24th to 48th hour, end node got an downlink from server, it will switch back to unconfirmed uplink. end node will restart ACK_Timout_1. If from the 24th to 48th hour, end node still not got any downlink, means device doesn't get ACK from server within last 48 hours. Device will process rejoin, rejoin request interval is AT+RJTDC period. For AU915/ US915, device will use the sub-band used for last join.
++* **Example 1:** Downlink Payload: 320105A00B40                     ~/~/ Set AT+DDETECT=1,1440,2880
--
  == 7.26 Request the server to send an ACK ==
@@ -1282,7 +1282,6 @@
  OK
  )))
--
  == 7.27 Adjust network rejoining interval ==
@@ -1291,13 +1291,13 @@
  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
  |=(% colspan="3" style="width: 724px;" %)AT+RJTDC
  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
--|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30(((
++|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30000(((
  OK
--the interval is 30 min
++the interval is 30000ms = 30s
  )))
--|(% style="width:165px" %)AT+RJTDC=60|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
--Set the ReJoin data transmission interval to 60 min
++|(% style="width:165px" %)AT+RJTDC=60000|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
++Set the ReJoin data transmission interval to 60000ms = 60 seconds
  )))
  (% style="color:blue" %)**Downlink Command: 0x26**
@@ -1309,7 +1309,6 @@
  * **Example 1:** Downlink Payload: 26000A                 ~/~/ Set AT+RJTDC=10
  * **Example 2: **Downlink Payload: 260002                 ~/~/ Set AT+RJTDC=2
--
  = 8. AT Commands Combination =
  == 8.1 Set a fix RX2DR for downlink window ==
@@ -1318,7 +1318,6 @@
  * (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
  * (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
--
  == 8.2 Use Downlink Command to set a fix uplink DR ==

Changes for page End Device AT Commands and Downlink Command

Summary

Details

Applications

Navigation