Last modified by kai on 2024/09/06 10:00
<
From version < 59.2 >
edited by Xiaoling
on 2023/01/29 11:16
To version < 38.103 >
edited by Xiaoling
on 2022/06/01 11:53
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,4 @@
1 - **Table of** **Contents：**
1 + **Contents：**
2 2  
3 3  {{toc/}}
4 4  
... ... @@ -6,25 +6,22 @@
6 6  
7 7  = 1. Introduction =
8 8  
9 -
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 -* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
11 +* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
12 +* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 -
18 18  
19 19  )))
20 20  
21 21  = 2. How to use AT Commands or Downlink command =
22 22  
23 -
24 -* **AT Command** : See Devices User Manual for how to connect to device via USB TTL adapter and use. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
25 -* **LoRaWAN Downlink Command**: The gateway transfer downlink command in HEX format. This page shows the Downlink Command In HEX format. Please note some LoRaWAN servers use base64 as downlink code so user need to convert HEX to Base64 and use. Below are references for how to use downlink command:
21 +* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 +* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
26 26  ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
27 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]], [[How to Convert>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.1ConvertHEXtoBase64]]?
24 +** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
28 28  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
29 29  
30 30  
... ... @@ -31,7 +31,6 @@
31 31  
32 32  = 3. Support End Node and firmware version =
33 33  
34 -
35 35  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
36 36  |=(% colspan="3" style="width: 963px;" %)(((
37 37  Dragino STM32 base hardware Firmware / LoRaWAN stack list
... ... @@ -109,12 +109,13 @@
109 109  
110 110  == 4.1 Change Uplink Interval ==
111 111  
112 -
113 113  Feature: Change LoRaWAN End Node Transmit Interval.
114 114  
110 +(% class="box infomessage" %)
111 +(((
112 +**AT Command: AT+TDC**
113 +)))
115 115  
116 -(% style="color:blue" %)**AT Command: AT+TDC**
117 -
118 118  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
119 119  |=(% colspan="3" style="width: 724px;" %)AT+TDC
120 120  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
... ... @@ -127,35 +127,33 @@
127 127  Set transmit interval to 60000ms = 60 seconds
128 128  )))
129 129  
130 -(((
131 -
127 +{{info}}
128 +**Downlink Command: 0x01**
129 +{{/info}}
132 132  
133 -(% style="color:blue" %)**Downlink Command: 0x01**
134 -
131 +(((
135 135  Format: Command Code (0x01) followed by 3 bytes time value.
136 136  )))
137 137  
138 138  (((
139 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
136 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
140 140  )))
141 141  
142 -* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
143 -* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
139 +* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
140 +* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
144 144  
145 -
146 -
147 147  == 4.2 Reboot End Node ==
148 148  
149 -
150 150  Feature: Reboot End Node to perform a new OTAA or ABP Join.
151 151  
146 +{{info}}
147 +**AT Command: ATZ**
148 +{{/info}}
152 152  
153 -(% style="color:blue" %)**AT Command: ATZ**
154 -
155 -(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
156 -|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
157 -|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
158 -|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
150 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
151 +|=(% colspan="3" %)ATZ: Trig a reset of the MCU
152 +|**Command Example**|**Function**|**Response**
153 +|ATZ|Reset MCU|(((
159 159  Device reset and show booting info
160 160  
161 161  LSN50 Device/LoRa ST Module
... ... @@ -169,7 +169,9 @@
169 169  <followed by the Tx and Rx information>
170 170  )))
171 171  
172 -(% style="color:blue" %)**Downlink Command: 0x04**
167 +{{info}}
168 +**Downlink Command: 0x04**
169 +{{/info}}
173 173  
174 174  (((
175 175  Format: Command Code (0x04) followed by FF.
... ... @@ -183,16 +183,16 @@
183 183  
184 184  == 4.3 Reset to factory Default ==
185 185  
186 -
187 187  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
188 188  
185 +{{info}}
186 +**AT Command: AT+FDR**
187 +{{/info}}
189 189  
190 -(% style="color:blue" %)**AT Command: AT+FDR**
191 -
192 -(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
193 -|=(% colspan="3" style="width: 786px;" %)Reset to factory default
194 -|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
195 -|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
189 +(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
190 +|=(% colspan="3" style="width: 828px;" %)Reset to factory default
191 +|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
192 +|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
196 196  Device reset to factory default parameters and show booting info
197 197  
198 198  LSN50 Device/LoRa ST Module
... ... @@ -206,7 +206,9 @@
206 206  Please set the parameters or reset Device to apply change
207 207  )))
208 208  
209 -(% style="color:blue" %)**Downlink Command: 0x04**
206 +{{info}}
207 +**Downlink Command: 0x04**
208 +{{/info}}
210 210  
211 211  (((
212 212  Format: Command Code (0x04) followed by FE.
... ... @@ -219,22 +219,24 @@
219 219  
220 220  == 4.4 Show Firmware Version ==
221 221  
222 -
223 223  Feature: Show firmware version. No downlink command yet.
224 224  
223 +{{info}}
224 +**AT Command: AT+VER**
225 +{{/info}}
225 225  
226 -(% style="color:blue" %)**AT Command: AT+VER**
227 -
228 -(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
229 -|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
230 -|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
231 -|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
227 +(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
228 +|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
229 +|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
230 +|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
232 232  1.3 EU868
233 233  
234 234  OK
235 235  )))
236 236  
237 -(% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
236 +{{info}}
237 +**Downlink Command: 0x26 (Valid in 006 stack)**
238 +{{/info}}
238 238  
239 239  (((
240 240  Downlink Format: 0x26
... ... @@ -245,8 +245,6 @@
245 245  )))
246 246  
247 247  (((
248 -
249 -
250 250  **xx: Software Type:**
251 251  )))
252 252  
... ... @@ -255,8 +255,6 @@
255 255  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
256 256  
257 257  (((
258 -
259 -
260 260  **yy: Frequency Band:**
261 261  )))
262 262  
... ... @@ -272,8 +272,6 @@
272 272  * 0xa0: AS923-3
273 273  
274 274  (((
275 -
276 -
277 277  **zz: Subband**
278 278  )))
279 279  
... ... @@ -282,12 +282,12 @@
282 282  
283 283  == 4.5 Show System Configure ==
284 284  
285 -
286 286  Feature: Show All configure. No downlink command yet.
287 287  
282 +{{info}}
283 +**AT Command: AT+CFG**
284 +{{/info}}
288 288  
289 -(% style="color:blue" %)**AT Command: AT+CFG**
290 -
291 291  (% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
292 292  |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
293 293  |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
... ... @@ -305,18 +305,16 @@
305 305  OK
306 306  )))
307 307  
308 -
309 -
310 310  = 5. Keys, IDs and EUIs management =
311 311  
312 312  == 5.1 Application EUI ==
313 313  
314 -
315 315  Feature: Get or Set the Application EUI.
316 316  
309 +{{info}}
310 +**AT Command: AT+APPEUI**
311 +{{/info}}
317 317  
318 -(% style="color:blue" %)**AT Command: AT+APPEUI**
319 -
320 320  (% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
321 321  |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
322 322  |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
... ... @@ -325,16 +325,14 @@
325 325  )))
326 326  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
327 327  
328 -
329 -
330 330  == 5.2 Application Key ==
331 331  
332 -
333 333  Feature: Get or Set the Application Key.
334 334  
325 +{{info}}
326 +**AT Command: AT+APPKEY**
327 +{{/info}}
335 335  
336 -(% style="color:blue" %)**AT Command: AT+APPKEY**
337 -
338 338  (% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
339 339  |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
340 340  |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
... ... @@ -343,16 +343,14 @@
343 343  )))
344 344  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
345 345  
346 -
347 -
348 348  == 5.3 Application Session Key ==
349 349  
350 -
351 351  Feature: Get or Set the Application Session Key.
352 352  
341 +{{info}}
342 +**AT Command: AT+APPSKEY**
343 +{{/info}}
353 353  
354 -(% style="color:blue" %)**AT Command: AT+APPSKEY**
355 -
356 356  (% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
357 357  |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
358 358  |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
... ... @@ -363,16 +363,14 @@
363 363  OK
364 364  )))
365 365  
366 -
367 -
368 368  == 5.4 Device Address ==
369 369  
370 -
371 371  Feature: Get or Set the Device Address.
372 372  
359 +{{info}}
360 +**AT Command: AT+DADDR**
361 +{{/info}}
373 373  
374 -(% style="color:blue" %)**AT Command: AT+DADDR**
375 -
376 376  (% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
377 377  |=(% colspan="3" style="width: 792px;" %)AT+DADDR
378 378  |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
... ... @@ -383,16 +383,14 @@
383 383  )))
384 384  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
385 385  
386 -
387 -
388 388  == 5.5 Device EUI ==
389 389  
390 -
391 391  Feature: Get or Set the Device EUI.
392 392  
377 +{{info}}
378 +**AT Command: AT+DEUI**
379 +{{/info}}
393 393  
394 -(% style="color:blue" %)**AT Command: AT+DEUI**
395 -
396 396  (% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
397 397  |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
398 398  |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
... ... @@ -403,16 +403,14 @@
403 403  OK
404 404  )))
405 405  
406 -
407 -
408 408  == 5.6 Network ID ==
409 409  
410 -
411 411  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
412 412  
395 +{{info}}
396 +**AT Command: AT+NWKID**
397 +{{/info}}
413 413  
414 -(% style="color:blue" %)**AT Command: AT+NWKID**
415 -
416 416  (% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
417 417  |=(% colspan="3" style="width: 445px;" %)AT+NWKID
418 418  |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
... ... @@ -421,16 +421,14 @@
421 421  )))
422 422  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
423 423  
424 -
425 -
426 426  == 5.7 Network Session Key ==
427 427  
428 -
429 429  Feature: Get or Set the Network Session Key
430 430  
411 +{{info}}
412 +**AT Command: AT+NWKSKEY**
413 +{{/info}}
431 431  
432 -(% style="color:blue" %)**AT Command: AT+NWKSKEY**
433 -
434 434  (% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
435 435  |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
436 436  |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
... ... @@ -439,20 +439,16 @@
439 439  )))
440 440  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
441 441  
442 -
443 -
444 444  = 6. Joining and sending date on LoRaWAN network =
445 445  
446 446  == 6.1 Confirm Mode ==
447 447  
448 -=== 6.1.1  AT+CFM command before DR-LWS007 software stack ===
449 -
450 -
451 451  Feature: Get or Set the confirmation mode (0-1).
452 452  
429 +{{info}}
430 +**AT Command: AT+CFM**
431 +{{/info}}
453 453  
454 -(% style="color:blue" %)**AT Command: AT+CFM**
455 -
456 456  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
457 457  |=(% colspan="3" style="width: 707px;" %)AT+CFM
458 458  |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
... ... @@ -462,89 +462,38 @@
462 462  |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
463 463  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
464 464  
465 -(% style="color:blue" %)**Downlink Command: 0x05**
442 +Downlink Command: 0x05
466 466  
467 467  Format: Command Code (0x05) followed by 2 bytes mode value.
468 468  
469 469  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
470 470  
471 -* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
472 -* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
448 +* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
449 +* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
473 473  
474 -
475 -
476 -=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
477 -
478 -
479 -(% style="color:blue" %)**AT Command: AT+CFM**
480 -
481 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
482 -|=(% colspan="3" style="width: 707px;" %)AT+CFM
483 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
484 -|(% style="width:160px" %)(((
485 -AT+CFM=1,0,0
486 -
487 -value1
488 -)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
489 -1
490 -
491 -OK
492 -)))
493 -|(% style="width:160px" %)(((
494 -AT+CFM=0,?,0
495 -
496 -value2
497 -)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
498 -0~~7
499 -
500 -OK
501 -)))
502 -|(% style="width:160px" %)(((
503 -AT+CFM=0,0,1
504 -
505 -value3
506 -)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
507 -1
508 -
509 -OK
510 -)))
511 -
512 -(% style="color:blue" %)**Downlink Command: 0x05**
513 -
514 -Format: Command Code (0x05) followed by 2 bytes mode value.
515 -
516 -If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
517 -
518 -* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
519 -* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
520 -
521 -
522 -
523 523  == 6.2 Confirm Status ==
524 524  
525 -
526 526  Feature: Get confirmation status of the last AT+SEND (0-1).
527 527  
455 +{{info}}
456 +**AT Command: AT+CFS**
457 +{{/info}}
528 528  
529 -(% style="color:blue" %)**AT Command: AT+CFS**
530 -
531 -(% border="1" style="background-color:#ffffcc; color:green; width:463px" %)
532 -|=(% colspan="3" style="width: 460px;" %)AT+CFS
533 -|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:107px" %)**Response**
534 -|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:107px" %)0(((
459 +(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
460 +|=(% colspan="3" style="width: 531px;" %)AT+CFS
461 +|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
462 +|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
535 535  OK
536 536  )))
537 537  
538 -
539 -
540 540  == 6.3 Join LoRa® Network ==
541 541  
542 -
543 543  Feature: Join network.
544 544  
470 +{{info}}
471 +**AT Command: AT+JOIN**
472 +{{/info}}
545 545  
546 -(% style="color:blue" %)**AT Command: AT+JOIN**
547 -
548 548  (% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
549 549  |=(% colspan="3" style="width: 644px;" %)AT+JOIN
550 550  |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
... ... @@ -554,16 +554,14 @@
554 554  While Error in format, return AT_BUSY_ERROR
555 555  )))
556 556  
557 -
558 -
559 559  == 6.4 LoRa® Network Join Mode ==
560 560  
561 -
562 562  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
563 563  
487 +{{info}}
488 +**AT Command: AT+NJM**
489 +{{/info}}
564 564  
565 -(% style="color:blue" %)**AT Command: AT+NJM**
566 -
567 567  (% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
568 568  |=(% colspan="3" style="width: 750px;" %)AT+NJM
569 569  |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
... ... @@ -573,25 +573,25 @@
573 573  |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
574 574  |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
575 575  
576 -(% style="color:blue" %)**Downlink Command: 0x20**
500 +{{info}}
501 +**Downlink Command: 0x20**
502 +{{/info}}
577 577  
578 578  Format: Command Code (0x20) followed by 1 bytes mode value.
579 579  
580 580  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
581 581  
582 -* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
583 -* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
508 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
509 +* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
584 584  
585 -
586 -
587 587  == 6.5 LoRa® Network Join Status ==
588 588  
589 -
590 590  Feature: LoRa® Network Join Status.
591 591  
515 +{{info}}
516 +**AT Command: AT+NJS**
517 +{{/info}}
592 592  
593 -(% style="color:blue" %)**AT Command: AT+NJS**
594 -
595 595  (% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
596 596  |=(% colspan="3" style="width: 495px;" %)AT+NJS
597 597  |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
... ... @@ -599,16 +599,14 @@
599 599  OK
600 600  )))
601 601  
602 -
603 -
604 604  == 6.6 Print Last Received Data in Raw Format ==
605 605  
606 -
607 607  Feature: Print Last Received Data in Raw Format<port:data>.
608 608  
530 +{{info}}
531 +**AT Command: AT+RECV**
532 +{{/info}}
609 609  
610 -(% style="color:blue" %)**AT Command: AT+RECV**
611 -
612 612  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
613 613  |=(% colspan="3" style="width: 584px;" %)AT+RECV
614 614  |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -616,16 +616,14 @@
616 616  OK
617 617  )))
618 618  
619 -
620 -
621 621  == 6.7 Print Last Received Data in Binary Format ==
622 622  
623 -
624 624  Feature: Print Last Received Data in Binary Format<port:data>.
625 625  
545 +{{info}}
546 +**AT Command: AT+RECVB**
547 +{{/info}}
626 626  
627 -(% style="color:blue" %)**AT Command: AT+RECVB**
628 -
629 629  (% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
630 630  |=(% colspan="3" style="width: 790px;" %)AT+RECVB
631 631  |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
... ... @@ -633,16 +633,14 @@
633 633  OK
634 634  )))
635 635  
636 -
637 -
638 638  == 6.8 Send Text Data ==
639 639  
640 -
641 641  Feature: Send Text Data<port:data>.
642 642  
560 +{{info}}
561 +**AT Command: AT+SEND**
562 +{{/info}}
643 643  
644 -(% style="color:blue" %)**AT Command: AT+SEND**
645 -
646 646  (% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
647 647  |=(% colspan="3" style="width: 988px;" %)AT+SEND
648 648  |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
... ... @@ -654,38 +654,34 @@
654 654  
655 655  )))
656 656  
657 -
658 -
659 659  == 6.9 Send Hexadecimal Data ==
660 660  
661 -
662 662  Feature: Send hexadecimal data along with the application port.
663 663  
579 +{{info}}
580 +**AT Command: AT+SENDB**
581 +{{/info}}
664 664  
665 -(% style="color:blue" %)**AT Command: AT+SENDB**
666 -
667 -(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
668 -|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
669 -|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
670 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
671 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
583 +(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
584 +|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
585 +|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
586 +|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
587 +|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
672 672  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
673 673  
674 674  
675 675  )))
676 676  
677 -
678 -
679 679  = 7. LoRaWAN network management =
680 680  
681 681  == 7.1 Adaptive Data Rate ==
682 682  
683 -
684 684  Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
685 685  
599 +{{info}}
600 +**AT Command: AT+ADR**
601 +{{/info}}
686 686  
687 -(% style="color:blue" %)**AT Command: AT+ADR**
688 -
689 689  (% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
690 690  |=(% colspan="3" style="width: 680px;" %)AT+ADR
691 691  |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
... ... @@ -697,23 +697,24 @@
697 697  AT_PARAM_ERROR
698 698  )))
699 699  
700 -(% style="color:blue" %)**Downlink Command: 0x22**
614 +{{info}}
615 +**Downlink Command: 0x22**
616 +{{/info}}
701 701  
618 +
702 702  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
703 703  
704 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
705 -* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
621 +* **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
622 +* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
706 706  
707 -
708 -
709 709  == 7.2 LoRa® Class ==
710 710  
711 -
712 712  Feature: Get or Set the Device Class(Currently only support class A, class C).
713 713  
628 +{{info}}
629 +**AT Command:AT+CLASS**
630 +{{/info}}
714 714  
715 -(% style="color:blue" %)**AT Command:  AT+CLASS**
716 -
717 717  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
718 718  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
719 719  |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
... ... @@ -724,16 +724,14 @@
724 724  
725 725  )))
726 726  
727 -
728 -
729 729  == 7.3 Duty Cycle Setting ==
730 730  
644 +Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
731 731  
732 -Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
646 +{{info}}
647 +**AT Command:AT+DCS**
648 +{{/info}}
733 733  
734 -
735 -(% style="color:blue" %)**AT Command:  AT+DCS**
736 -
737 737  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
738 738  |=(% colspan="3" style="width: 512px;" %)AT+DCS
739 739  |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
... ... @@ -744,21 +744,14 @@
744 744  
745 745  )))
746 746  
747 -
748 -
749 749  == 7.4 Data Rate ==
750 750  
662 +Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
751 751  
752 -Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) .
664 +{{info}}
665 +**AT Command: AT+DR**
666 +{{/info}}
753 753  
754 -(% style="color:red" %)
755 -**Notice:**
756 -
757 -* User need to set Adaptive Data Rate(ADR)=0 first. otherwise device will respond to server's ADR command and change the DR according to server auto-adjustment.
758 -* Data Rate specifies Spreading Factor. The mapping varies in different frequency bands. User can check this link for detail. [[rp2-1.0.3-lorawan-regional-parameters.pdf>>https://lora-alliance.org/resource_hub/rp2-1-0-3-lorawan-regional-parameters/]]
759 -
760 -(% style="color:blue" %)**AT Command: AT+DR**
761 -
762 762  (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
763 763  |=(% colspan="3" style="width: 463px;" %)AT+DR
764 764  |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -769,23 +769,24 @@
769 769  
770 770  )))
771 771  
772 -(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
678 +{{info}}
679 +**Downlink Command: 0x2200aaFF**
680 +{{/info}}
773 773  
682 +
774 774  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
775 775  
776 -* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
777 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
685 +* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
686 +* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
778 778  
779 -
780 -
781 781  == 7.5 Frame Counter Downlink ==
782 782  
783 -
784 784  Feature: Get or Set the Frame Counter Downlink.
785 785  
692 +{{info}}
693 +**AT Command:AT+FCD**
694 +{{/info}}
786 786  
787 -(% style="color:blue" %)**AT Command:  AT+FCD**
788 -
789 789  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
790 790  |=(% colspan="3" style="width: 690px;" %)AT+FCD
791 791  |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
... ... @@ -794,17 +794,18 @@
794 794  )))
795 795  |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
796 796  OK
704 +
705 +
797 797  )))
798 798  
799 -
800 -
801 801  == 7.6 Frame Counter Uplink ==
802 802  
803 803  Feature: Get or Set the Frame Counter Uplink.
804 804  
712 +{{info}}
713 +**AT Command:AT+FCU**
714 +{{/info}}
805 805  
806 -(% style="color:blue" %)**AT Command:  AT+FCU**
807 -
808 808  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
809 809  |=(% colspan="3" style="width: 531px;" %)AT+FCU
810 810  |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -815,16 +815,14 @@
815 815  
816 816  )))
817 817  
818 -
819 -
820 820  == 7.7 Join Accept Delay1 ==
821 821  
822 -
823 823  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
824 824  
730 +{{info}}
731 +**AT Command:AT+JN1DL**
732 +{{/info}}
825 825  
826 -(% style="color:blue" %)**AT Command:  AT+JN1DL**
827 -
828 828  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
829 829  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
830 830  |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -835,16 +835,14 @@
835 835  
836 836  )))
837 837  
838 -
839 -
840 840  == 7.8 Join Accept Delay2 ==
841 841  
842 -
843 843  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
844 844  
748 +{{info}}
749 +**AT Command:AT+JN2DL**
750 +{{/info}}
845 845  
846 -(% style="color:blue" %)**AT Command:  AT+JN2DL**
847 -
848 848  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
849 849  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
850 850  |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
... ... @@ -855,18 +855,14 @@
855 855  
856 856  )))
857 857  
858 -
859 -
860 860  == 7.9 Public Network Mode ==
861 861  
764 +Feature: Get or Set the public network mode. (0: off, 1: on)
862 862  
863 -Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
766 +{{info}}
767 +**AT Command:AT+PNM**
768 +{{/info}}
864 864  
865 -(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
866 -
867 -
868 -(% style="color:blue" %)**AT Command:  AT+PNM**
869 -
870 870  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
871 871  |=(% colspan="3" style="width: 664px;" %)AT+PNM
872 872  |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
... ... @@ -873,27 +873,20 @@
873 873  |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
874 874  OK
875 875  )))
876 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
877 -Set the public network mode.
878 -
879 -Set syncword=0x34
880 -)))|(% style="width:272px" %)(System will write new value to PNM)(((
776 +|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
881 881  OK
882 882  
883 883  
884 884  )))
885 -|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
886 886  
887 -
888 -
889 889  == 7.10 Receive Delay1 ==
890 890  
891 -
892 892  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
893 893  
786 +{{info}}
787 +**AT Command:AT+RX1DL**
788 +{{/info}}
894 894  
895 -(% style="color:blue" %)**AT Command: AT+RX1DL**
896 -
897 897  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
898 898  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
899 899  |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -904,16 +904,14 @@
904 904  
905 905  )))
906 906  
907 -
908 -
909 909  == 7.11 Receive Delay2 ==
910 910  
911 -
912 912  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
913 913  
804 +{{info}}
805 +**AT Command:AT+RX2DL**
806 +{{/info}}
914 914  
915 -(% style="color:blue" %)**AT Command: AT+RX2DL**
916 -
917 917  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
918 918  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
919 919  |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -924,16 +924,14 @@
924 924  
925 925  )))
926 926  
927 -
928 -
929 929  == 7.12 Rx2 Window Data Rate ==
930 930  
931 -
932 932  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
933 933  
822 +{{info}}
823 +**AT Command:AT+RX2DR**
824 +{{/info}}
934 934  
935 -(% style="color:blue" %)**AT Command:  AT+RX2DR**
936 -
937 937  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
938 938  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
939 939  |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
... ... @@ -944,16 +944,14 @@
944 944  
945 945  )))
946 946  
947 -
948 -
949 949  == 7.13 Rx2 Window Frequency ==
950 950  
951 -
952 952  Feature: Get or Set the Rx2 window frequency
953 953  
840 +{{info}}
841 +**AT Command:AT+RX2FQ**
842 +{{/info}}
954 954  
955 -(% style="color:blue" %)**AT Command:  AT+RX2FQ**
956 -
957 957  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
958 958  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
959 959  |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
... ... @@ -964,18 +964,14 @@
964 964  
965 965  )))
966 966  
967 -
968 -
969 969  == 7.14 Transmit Power ==
970 970  
971 -
972 972  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
973 973  
974 -(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
858 +{{info}}
859 +**AT Command:AT+TXP**
860 +{{/info}}
975 975  
976 -
977 -(% style="color:blue" %)**AT Command:  AT+TXP**
978 -
979 979  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
980 980  |=(% colspan="3" style="width: 462px;" %)AT+TXP
981 981  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -990,19 +990,17 @@
990 990  
991 991  If the downlink payload=22000100, it means setting the TXP to 0.
992 992  
993 -* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
994 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
876 +* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
877 +* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
995 995  
996 -
997 -
998 998  == 7.15 RSSI of the Last Received Packet ==
999 999  
1000 -
1001 1001  Feature: Get or Set the Rx2 window frequency
1002 1002  
883 +{{info}}
884 +**AT Command:AT+RSSI**
885 +{{/info}}
1003 1003  
1004 -(% style="color:blue" %)**AT Command:AT+RSSI**
1005 -
1006 1006  (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
1007 1007  |=(% colspan="3" style="width: 554px;" %)AT+RSSI
1008 1008  |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
... ... @@ -1010,16 +1010,14 @@
1010 1010  OK
1011 1011  )))
1012 1012  
1013 -
1014 -
1015 1015  == 7.16 SNR of the Last Received Packet ==
1016 1016  
1017 -
1018 1018  Feature: Get the SNR of the last received packet
1019 1019  
898 +{{info}}
899 +**AT Command:AT+SNR**
900 +{{/info}}
1020 1020  
1021 -(% style="color:blue" %)**AT Command:  AT+SNR**
1022 -
1023 1023  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
1024 1024  |=(% colspan="3" style="width: 568px;" %)AT+SNR
1025 1025  |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -1027,16 +1027,14 @@
1027 1027  OK
1028 1028  )))
1029 1029  
1030 -
1031 -
1032 1032  == 7.17 Application Port ==
1033 1033  
1034 -
1035 1035  Feature: Get or set the application port.
1036 1036  
913 +{{info}}
914 +**AT Command: AT+PORT**
915 +{{/info}}
1037 1037  
1038 -(% style="color:blue" %)**AT Command: AT+PORT**
1039 -
1040 1040  (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
1041 1041  |=(% colspan="3" style="width: 497px;" %)AT+PORT
1042 1042  |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
... ... @@ -1045,25 +1045,25 @@
1045 1045  )))
1046 1046  |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
1047 1047  
1048 -(% style="color:blue" %)**Downlink Command: 0x23**
925 +{{info}}
926 +**Downlink Command: 0x23**
927 +{{/info}}
1049 1049  
1050 1050  Format: Command Code (0x23) followed by 1 bytes port value.
1051 1051  
1052 1052  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1053 1053  
1054 -* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1055 -* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
933 +* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
934 +* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1056 1056  
1057 -
1058 -
1059 1059  == 7.18 Single Channel Mode ==
1060 1060  
1061 -
1062 1062  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
1063 1063  
940 +{{info}}
941 +**AT Command: AT+CHS**
942 +{{/info}}
1064 1064  
1065 -(% style="color:blue" %)**AT Command: AT+CHS**
1066 -
1067 1067  (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
1068 1068  |=(% colspan="3" style="width: 600px;" %)AT+CHS
1069 1069  |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -1072,16 +1072,14 @@
1072 1072  )))
1073 1073  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1074 1074  
1075 -
1076 -
1077 1077  == 7.19 Eight Channel Mode ==
1078 1078  
1079 -
1080 1080  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1081 1081  
956 +{{info}}
957 +**AT Command: AT+CHE**
958 +{{/info}}
1082 1082  
1083 -(% style="color:blue" %)**AT Command: AT+CHE**
1084 -
1085 1085  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1086 1086  |=(% colspan="3" style="width: 707px;" %)AT+CHE
1087 1087  |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
... ... @@ -1092,25 +1092,25 @@
1092 1092  )))
1093 1093  |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1094 1094  
1095 -(% style="color:blue" %)**Downlink Command: 0x24 (LHT65,LHT65N Downlink Command:0x07)**
970 +{{info}}
971 +**Downlink Command: 0x24**
972 +{{/info}}
1096 1096  
1097 1097  Format: Command Code (0x24) followed by 1 bytes channel value.
1098 1098  
1099 1099  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1100 1100  
1101 -* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1102 -* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
978 +* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
979 +* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1103 1103  
1104 -
1105 -
1106 1106  == 7.20 Get or Set RXwindows1 timeout ==
1107 1107  
983 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1108 1108  
1109 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
985 +{{info}}
986 +**AT Command: AT+RX1WTO**
987 +{{/info}}
1110 1110  
1111 -
1112 -(% style="color:blue" %)**AT Command: AT+RX1WTO**
1113 -
1114 1114  (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1115 1115  |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1116 1116  |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
... ... @@ -1120,17 +1120,11 @@
1120 1120  |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1121 1121  
1122 1122  (((
1123 -
1124 -
1125 -
1126 -(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1127 -
1128 -
998 +**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1129 1129  )))
1130 1130  
1131 1131  [[image:image-20220526162535-1.png]]
1132 1132  
1133 -
1134 1134  (((
1135 1135  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1136 1136  
... ... @@ -1139,12 +1139,12 @@
1139 1139  
1140 1140  == 7.21 Get or Set RXwindows2 timeout ==
1141 1141  
1011 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1142 1142  
1143 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1013 +{{info}}
1014 +**AT Command: AT+RX2WTO**
1015 +{{/info}}
1144 1144  
1145 -
1146 -(% style="color:blue" %)**AT Command: AT+RX2WTO**
1147 -
1148 1148  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1149 1149  |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1150 1150  |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
... ... @@ -1153,16 +1153,14 @@
1153 1153  )))
1154 1154  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1155 1155  
1156 -
1157 -
1158 1158  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1159 1159  
1160 -
1161 1161  Feature: Get or Set uplinkdwelltime
1162 1162  
1029 +{{info}}
1030 +**AT Command: AT+DWELLT**
1031 +{{/info}}
1163 1163  
1164 -(% style="color:blue" %)**AT Command: AT+DWELLT**
1165 -
1166 1166  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1167 1167  |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1168 1168  |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
... ... @@ -1171,25 +1171,23 @@
1171 1171  )))
1172 1172  |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1173 1173  
1174 -(% style="color:blue" %)**Downlink Command: 0x25**
1041 +{{info}}
1042 +**Downlink Command: 0x25**
1043 +{{/info}}
1175 1175  
1176 1176  Format: Command Code (0x25) followed by 1 bytes state value.
1177 1177  
1178 1178  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1179 1179  
1180 -* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1181 -* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1049 +* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1050 +* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1182 1182  
1183 -
1184 -
1185 1185  == 7.23 Set Packet Receiving Response Level ==
1186 1186  
1187 -
1188 1188  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1189 1189  
1056 +RPL value:
1190 1190  
1191 -**RPL value:**
1192 -
1193 1193  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1194 1194  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1195 1195  * **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
... ... @@ -1196,13 +1196,15 @@
1196 1196  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1197 1197  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1198 1198  
1199 -**Case Analyes:**
1064 +Case Analyes:
1200 1200  
1201 1201  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1202 1202  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1203 1203  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1204 1204  
1205 -(% style="color:blue" %)**AT Command: AT+RPL**
1070 +{{info}}
1071 +**AT Command: AT+RPL**
1072 +{{/info}}
1206 1206  
1207 1207  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1208 1208  |=(% colspan="3" style="width: 533px;" %)AT+RPL
... ... @@ -1212,161 +1212,32 @@
1212 1212  )))
1213 1213  |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1214 1214  
1215 -(% style="color:blue" %)**Downlink Command: 0x21**
1082 +{{info}}
1083 +**Downlink Command: 0x21**
1084 +{{/info}}
1216 1216  
1217 1217  Format: Command Code (0x21) followed by 1 bytes level value.
1218 1218  
1219 1219  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1220 1220  
1221 -* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1222 -* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1090 +* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1091 +* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1223 1223  
1224 -
1225 -
1226 -== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1227 -
1228 -
1229 -(% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1230 -
1231 -(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1232 -|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1233 -|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1234 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1235 -OK
1236 -)))
1237 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1238 -value2: 0: uplink fcnt doesn't change for each NBTrans;
1239 -
1240 -1: uplink fcnt increase by 1 for each NBTrans.
1241 -)))|(% style="width:87px" %)(((
1242 -1
1243 -
1244 -OK
1245 -)))
1246 -
1247 -(% style="color:blue" %)**Downlink Command: 0x33**
1248 -
1249 -Format: Command Code (0x33) followed by 2 bytes mode value.
1250 -
1251 -If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1252 -
1253 -* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1254 -* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1255 -
1256 -
1257 -
1258 -== 7.25 Device offline rejoining （LWS007) ==
1259 -
1260 -
1261 -(% style="color:blue" %)**AT Command: AT+DDETECT**
1262 -
1263 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1264 -|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1265 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1266 -|(% style="width:160px" %)(((
1267 -AT+DDETECT=1,1440,2880
1268 -
1269 -value1
1270 -)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1271 -1
1272 -
1273 -OK
1274 -)))
1275 -|(% style="width:160px" %)(((
1276 -AT+DDETECT=1,?,2880
1277 -
1278 -value2
1279 -)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1280 -
1281 -
1282 -OK
1283 -)))
1284 -|(% style="width:160px" %)(((
1285 -AT+DDETECT=1,1440,？
1286 -
1287 -value3
1288 -)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1289 -
1290 -
1291 -OK
1292 -)))
1293 -
1294 -(% style="color:blue" %)**Downlink Command: 0x33**
1295 -
1296 -Format: Command Code (0x32) followed by 2 bytes mode value.
1297 -
1298 -If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1299 -
1300 -* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1301 -
1302 -
1303 -
1304 -== 7.26 Request the server to send an ACK ==
1305 -
1306 -
1307 -(% style="color:blue" %)**AT Command: AT+PNACKMD**
1308 -
1309 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1310 -|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1311 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1312 -|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1313 -OK
1314 -)))
1315 -|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1316 -0
1317 -
1318 -OK
1319 -)))
1320 -
1321 -
1322 -
1323 -== 7.27 Adjust network rejoining interval ==
1324 -
1325 -
1326 -(% style="color:blue" %)**AT Command: AT+RJTDC**
1327 -
1328 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1329 -|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1330 -|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1331 -|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30(((
1332 -OK
1333 -
1334 -the interval is 30 min
1335 -)))
1336 -|(% style="width:165px" %)AT+RJTDC=60|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1337 -Set the ReJoin data transmission interval to 60 min
1338 -)))
1339 -
1340 -(% style="color:blue" %)**Downlink Command: 0x26**
1341 -
1342 -Format: Command Code (0x26) followed by 2 bytes mode value.
1343 -
1344 -If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1345 -
1346 -* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1347 -* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1348 -
1349 -
1350 -
1351 1351  = 8. AT Commands Combination =
1352 1352  
1353 1353  == 8.1 Set a fix RX2DR for downlink window ==
1354 1354  
1097 +* **AT+ADR=0 **~-~-> Disable ADR first
1098 +* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1355 1355  
1356 -* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1357 -* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1358 -
1359 -
1360 -
1361 1361  == 8.2 Use Downlink Command to set a fix uplink DR ==
1362 1362  
1102 +{{info}}
1103 +**Downlink Command: 0x22000500**
1104 +{{/info}}
1363 1363  
1364 -(% style="color:blue" %)**Downlink Command: 0x22000500**
1106 +Same as:
1365 1365  
1366 -**Same as:**
1367 -
1368 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1369 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1370 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1371 -
1372 -
1108 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1109 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1110 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0