<
From version < 58.3 >
edited by Xiaoling
on 2022/12/02 13:51
To version < 54.1 >
edited by Edwin Chen
on 2022/10/16 07:37
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.Edwin
Content
... ... @@ -14,6 +14,7 @@
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 +
17 17  
18 18  
19 19  )))
... ... @@ -21,13 +21,14 @@
21 21  = 2. How to use AT Commands or Downlink command =
22 22  
23 23  
24 -* **AT Command** See Devices User Manual for how to connect to device via USB TTL adapter and use. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
25 -* **LoRaWAN Downlink Command**: The gateway transfer downlink command in HEX format. This page shows the Downlink Command In HEX format. Please note some LoRaWAN servers use base64 as downlink code so user need to convert HEX to Base64 and use. Below are references for how to use downlink command:
25 +* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
26 +* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
26 26  ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
27 27  ** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]], [[How to Convert>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.1ConvertHEXtoBase64]]?
28 28  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
29 29  
30 30  
32 +
31 31  = 3. Support End Node and firmware version =
32 32  
33 33  
... ... @@ -177,6 +177,7 @@
177 177  (((
178 178  If the downlink payload=**04FF**, the end node will reboot.
179 179  
182 +
180 180  
181 181  )))
182 182  
... ... @@ -216,6 +216,7 @@
216 216  )))
217 217  
218 218  
222 +
219 219  == 4.4 Show Firmware Version ==
220 220  
221 221  
... ... @@ -246,6 +246,7 @@
246 246  (((
247 247  
248 248  
253 +
249 249  **xx: Software Type:**
250 250  )))
251 251  
... ... @@ -279,6 +279,7 @@
279 279  firmware version: v1.1.0 ~-~-> 110
280 280  
281 281  
287 +
282 282  == 4.5 Show System Configure ==
283 283  
284 284  
... ... @@ -751,11 +751,9 @@
751 751  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) .
752 752  
753 753  (% style="color:red" %)
754 -**Notice:**
760 +Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server.
761 +(%%)
755 755  
756 -* User need to set Adaptive Data Rate(ADR)=0 first. otherwise device will respond to server's ADR command and change the DR according to server auto-adjustment.
757 -* Data Rate specifies Spreading Factor. The mapping varies in different frequency bands. User can check this link for detail. [[rp2-1.0.3-lorawan-regional-parameters.pdf>>https://lora-alliance.org/resource_hub/rp2-1-0-3-lorawan-regional-parameters/]]
758 -
759 759  (% style="color:blue" %)**AT Command: AT+DR**
760 760  
761 761  (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
... ... @@ -1091,7 +1091,7 @@
1091 1091  )))
1092 1092  |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1093 1093  
1094 -(% style="color:blue" %)**Downlink Command: 0x24 (LHT65,LHT65N Downlink Command:0x07)**
1098 +(% style="color:blue" %)**Downlink Command: 0x24**
1095 1095  
1096 1096  Format: Command Code (0x24) followed by 1 bytes channel value.
1097 1097  
... ... @@ -1133,6 +1133,7 @@
1133 1133  (((
1134 1134  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1135 1135  
1140 +
1136 1136  
1137 1137  )))
1138 1138  
Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0