Last modified by kai on 2024/09/06 10:00
<
From version < 56.1 >
edited by Edwin Chen
on 2022/10/16 07:44
To version < 51.4 >
edited by Xiaoling
on 2022/07/13 14:10
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Edwin
1 +XWiki.Xiaoling
Content
... ... @@ -9,14 +9,12 @@
9 9  
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 -* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
12 +* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
13 +* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 -
19 -
20 20  )))
21 21  
22 22  = 2. How to use AT Commands or Downlink command =
... ... @@ -25,9 +25,12 @@
25 25  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
26 26  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
27 27  ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
28 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]], [[How to Convert>>http://wiki.dragino.com/xwiki/bin/view/Main/Notes%20for%20ChirpStack/#H4.1ConvertHEXtoBase64]]?
26 +** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
29 29  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
30 30  
29 +
30 +
31 +
31 31  = 3. Support End Node and firmware version =
32 32  
33 33  
... ... @@ -102,8 +102,12 @@
102 102  )))
103 103  )))
104 104  
106 +
107 +
108 +
105 105  = 4. System Management Commands =
106 106  
111 +
107 107  == 4.1 Change Uplink Interval ==
108 108  
109 109  
... ... @@ -133,12 +133,15 @@
133 133  )))
134 134  
135 135  (((
136 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
141 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
137 137  )))
138 138  
139 -* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
140 -* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
144 +* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 +* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
141 141  
147 +
148 +
149 +
142 142  == 4.2 Reboot End Node ==
143 143  
144 144  
... ... @@ -147,10 +147,10 @@
147 147  
148 148  (% style="color:blue" %)**AT Command: ATZ**
149 149  
150 -(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
151 -|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
152 -|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
153 -|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
158 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
159 +|=(% colspan="3" %)ATZ: Trig a reset of the MCU
160 +|**Command Example**|**Function**|**Response**
161 +|ATZ|Reset MCU|(((
154 154  Device reset and show booting info
155 155  
156 156  LSN50 Device/LoRa ST Module
... ... @@ -173,7 +173,6 @@
173 173  (((
174 174  If the downlink payload=**04FF**, the end node will reboot.
175 175  
176 -
177 177  
178 178  )))
179 179  
... ... @@ -185,10 +185,10 @@
185 185  
186 186  (% style="color:blue" %)**AT Command: AT+FDR**
187 187  
188 -(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
189 -|=(% colspan="3" style="width: 786px;" %)Reset to factory default
190 -|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
191 -|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
195 +(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
196 +|=(% colspan="3" style="width: 828px;" %)Reset to factory default
197 +|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
198 +|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
192 192  Device reset to factory default parameters and show booting info
193 193  
194 194  LSN50 Device/LoRa ST Module
... ... @@ -213,7 +213,6 @@
213 213  )))
214 214  
215 215  
216 -
217 217  == 4.4 Show Firmware Version ==
218 218  
219 219  
... ... @@ -222,10 +222,10 @@
222 222  
223 223  (% style="color:blue" %)**AT Command: AT+VER**
224 224  
225 -(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
226 -|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
227 -|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
228 -|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
231 +(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
232 +|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
233 +|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
234 +|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
229 229  1.3 EU868
230 230  
231 231  OK
... ... @@ -278,7 +278,6 @@
278 278  firmware version: v1.1.0 ~-~-> 110
279 279  
280 280  
281 -
282 282  == 4.5 Show System Configure ==
283 283  
284 284  
... ... @@ -304,8 +304,11 @@
304 304  OK
305 305  )))
306 306  
312 +
313 +
307 307  = 5. Keys, IDs and EUIs management =
308 308  
316 +
309 309  == 5.1 Application EUI ==
310 310  
311 311  
... ... @@ -322,6 +322,8 @@
322 322  )))
323 323  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
324 324  
333 +
334 +
325 325  == 5.2 Application Key ==
326 326  
327 327  
... ... @@ -338,6 +338,8 @@
338 338  )))
339 339  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
340 340  
351 +
352 +
341 341  == 5.3 Application Session Key ==
342 342  
343 343  
... ... @@ -426,8 +426,10 @@
426 426  
427 427  = 6. Joining and sending date on LoRaWAN network =
428 428  
441 +
429 429  == 6.1 Confirm Mode ==
430 430  
444 +
431 431  === 6.1.1  AT+CFM command before DR-LWS007 software stack ===
432 432  
433 433  
... ... @@ -451,9 +451,10 @@
451 451  
452 452  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
453 453  
454 -* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
455 -* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
468 +* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
469 +* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
456 456  
471 +
457 457  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
458 458  
459 459  
... ... @@ -496,9 +496,10 @@
496 496  
497 497  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
498 498  
499 -* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
500 -* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
514 +* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
515 +* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
501 501  
517 +
502 502  == 6.2 Confirm Status ==
503 503  
504 504  
... ... @@ -554,9 +554,10 @@
554 554  
555 555  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
556 556  
557 -* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
558 -* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
573 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
574 +* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
559 559  
576 +
560 560  == 6.5 LoRa® Network Join Status ==
561 561  
562 562  
... ... @@ -629,11 +629,11 @@
629 629  
630 630  (% style="color:blue" %)**AT Command: AT+SENDB**
631 631  
632 -(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
633 -|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
634 -|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
635 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
636 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
649 +(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
650 +|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
651 +|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
652 +|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
653 +|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
637 637  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
638 638  
639 639  
... ... @@ -641,6 +641,7 @@
641 641  
642 642  = 7. LoRaWAN network management =
643 643  
661 +
644 644  == 7.1 Adaptive Data Rate ==
645 645  
646 646  
... ... @@ -664,8 +664,8 @@
664 664  
665 665  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
666 666  
667 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
668 -* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
685 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
686 +* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
669 669  
670 670  
671 671  == 7.2 LoRa® Class ==
... ... @@ -674,7 +674,7 @@
674 674  Feature: Get or Set the Device Class(Currently only support class A, class C).
675 675  
676 676  
677 -(% style="color:blue" %)**AT Command:  AT+CLASS**
695 +(% style="color:blue" %)**AT Command:AT+CLASS**
678 678  
679 679  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
680 680  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
... ... @@ -689,10 +689,10 @@
689 689  == 7.3 Duty Cycle Setting ==
690 690  
691 691  
692 -Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
710 +Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
693 693  
694 694  
695 -(% style="color:blue" %)**AT Command:  AT+DCS**
713 +(% style="color:blue" %)**AT Command:AT+DCS**
696 696  
697 697  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
698 698  |=(% colspan="3" style="width: 512px;" %)AT+DCS
... ... @@ -707,14 +707,9 @@
707 707  == 7.4 Data Rate ==
708 708  
709 709  
710 -Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) .
728 +Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
711 711  
712 -(% style="color:red" %)
713 -**Notice:**
714 714  
715 -* User need to set Adaptive Data Rate(ADR)=0 first. otherwise device will respond to server's ADR command and change the DR according to server auto-adjustment.
716 -* Data Rate specifies Spreading Factor. The mapping varies in different frequency bands. User can check this link for detail. [[rp2-1.0.3-lorawan-regional-parameters.pdf>>https://lora-alliance.org/resource_hub/rp2-1-0-3-lorawan-regional-parameters/]]
717 -
718 718  (% style="color:blue" %)**AT Command: AT+DR**
719 719  
720 720  (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
... ... @@ -731,8 +731,8 @@
731 731  
732 732  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
733 733  
734 -* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
735 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
747 +* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
748 +* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
736 736  
737 737  
738 738  == 7.5 Frame Counter Downlink ==
... ... @@ -741,7 +741,7 @@
741 741  Feature: Get or Set the Frame Counter Downlink.
742 742  
743 743  
744 -(% style="color:blue" %)**AT Command:  AT+FCD**
757 +(% style="color:blue" %)**AT Command:AT+FCD**
745 745  
746 746  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
747 747  |=(% colspan="3" style="width: 690px;" %)AT+FCD
... ... @@ -758,7 +758,7 @@
758 758  Feature: Get or Set the Frame Counter Uplink.
759 759  
760 760  
761 -(% style="color:blue" %)**AT Command:  AT+FCU**
774 +(% style="color:blue" %)**AT Command:AT+FCU**
762 762  
763 763  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
764 764  |=(% colspan="3" style="width: 531px;" %)AT+FCU
... ... @@ -776,7 +776,7 @@
776 776  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
777 777  
778 778  
779 -(% style="color:blue" %)**AT Command:  AT+JN1DL**
792 +(% style="color:blue" %)**AT Command:AT+JN1DL**
780 780  
781 781  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
782 782  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
... ... @@ -790,11 +790,10 @@
790 790  
791 791  == 7.8 Join Accept Delay2 ==
792 792  
793 -
794 794  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
795 795  
796 796  
797 -(% style="color:blue" %)**AT Command:  AT+JN2DL**
809 +(% style="color:blue" %)**AT Command:AT+JN2DL**
798 798  
799 799  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
800 800  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
... ... @@ -811,10 +811,10 @@
811 811  
812 812  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
813 813  
814 -(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
826 +(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
815 815  
816 816  
817 -(% style="color:blue" %)**AT Command:  AT+PNM**
829 +(% style="color:blue" %)**AT Command:AT+PNM**
818 818  
819 819  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
820 820  |=(% colspan="3" style="width: 664px;" %)AT+PNM
... ... @@ -839,7 +839,7 @@
839 839  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
840 840  
841 841  
842 -(% style="color:blue" %)**AT Command: AT+RX1DL**
854 +(% style="color:blue" %)**AT Command:AT+RX1DL**
843 843  
844 844  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
845 845  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
... ... @@ -851,6 +851,7 @@
851 851  
852 852  )))
853 853  
866 +
854 854  == 7.11 Receive Delay2 ==
855 855  
856 856  
... ... @@ -857,7 +857,7 @@
857 857  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
858 858  
859 859  
860 -(% style="color:blue" %)**AT Command: AT+RX2DL**
873 +(% style="color:blue" %)**AT Command:AT+RX2DL**
861 861  
862 862  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
863 863  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
... ... @@ -869,6 +869,7 @@
869 869  
870 870  )))
871 871  
885 +
872 872  == 7.12 Rx2 Window Data Rate ==
873 873  
874 874  
... ... @@ -875,7 +875,7 @@
875 875  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
876 876  
877 877  
878 -(% style="color:blue" %)**AT Command:  AT+RX2DR**
892 +(% style="color:blue" %)**AT Command:AT+RX2DR**
879 879  
880 880  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
881 881  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
... ... @@ -887,6 +887,7 @@
887 887  
888 888  )))
889 889  
904 +
890 890  == 7.13 Rx2 Window Frequency ==
891 891  
892 892  
... ... @@ -893,7 +893,7 @@
893 893  Feature: Get or Set the Rx2 window frequency
894 894  
895 895  
896 -(% style="color:blue" %)**AT Command:  AT+RX2FQ**
911 +(% style="color:blue" %)**AT Command:AT+RX2FQ**
897 897  
898 898  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
899 899  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
... ... @@ -905,16 +905,15 @@
905 905  
906 906  )))
907 907  
923 +
908 908  == 7.14 Transmit Power ==
909 909  
910 910  
911 911  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
912 912  
913 -(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
914 914  
930 +(% style="color:blue" %)**AT Command:AT+TXP**
915 915  
916 -(% style="color:blue" %)**AT Command:  AT+TXP**
917 -
918 918  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
919 919  |=(% colspan="3" style="width: 462px;" %)AT+TXP
920 920  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -929,9 +929,11 @@
929 929  
930 930  If the downlink payload=22000100, it means setting the TXP to 0.
931 931  
932 -* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
933 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
946 +* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
947 +* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
934 934  
949 +
950 +
935 935  == 7.15 RSSI of the Last Received Packet ==
936 936  
937 937  
... ... @@ -947,6 +947,7 @@
947 947  OK
948 948  )))
949 949  
966 +
950 950  == 7.16 SNR of the Last Received Packet ==
951 951  
952 952  
... ... @@ -953,7 +953,7 @@
953 953  Feature: Get the SNR of the last received packet
954 954  
955 955  
956 -(% style="color:blue" %)**AT Command:  AT+SNR**
973 +(% style="color:blue" %)**AT Command:AT+SNR**
957 957  
958 958  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
959 959  |=(% colspan="3" style="width: 568px;" %)AT+SNR
... ... @@ -962,6 +962,7 @@
962 962  OK
963 963  )))
964 964  
982 +
965 965  == 7.17 Application Port ==
966 966  
967 967  
... ... @@ -984,9 +984,11 @@
984 984  
985 985  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
986 986  
987 -* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
988 -* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1005 +* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1006 +* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
989 989  
1008 +
1009 +
990 990  == 7.18 Single Channel Mode ==
991 991  
992 992  
... ... @@ -1003,9 +1003,9 @@
1003 1003  )))
1004 1004  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1005 1005  
1026 +
1006 1006  == 7.19 Eight Channel Mode ==
1007 1007  
1008 -
1009 1009  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1010 1010  
1011 1011  
... ... @@ -1027,9 +1027,11 @@
1027 1027  
1028 1028  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1029 1029  
1030 -* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1031 -* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1050 +* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1051 +* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1032 1032  
1053 +
1054 +
1033 1033  == 7.20 Get or Set RXwindows1 timeout ==
1034 1034  
1035 1035  
... ... @@ -1049,9 +1049,8 @@
1049 1049  (((
1050 1050  
1051 1051  
1074 +**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1052 1052  
1053 -(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1054 -
1055 1055  
1056 1056  )))
1057 1057  
... ... @@ -1061,7 +1061,6 @@
1061 1061  (((
1062 1062  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1063 1063  
1064 -
1065 1065  
1066 1066  )))
1067 1067  
... ... @@ -1081,6 +1081,7 @@
1081 1081  )))
1082 1082  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1083 1083  
1104 +
1084 1084  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1085 1085  
1086 1086  
... ... @@ -1103,9 +1103,11 @@
1103 1103  
1104 1104  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1105 1105  
1106 -* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1107 -* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1127 +* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1128 +* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1108 1108  
1130 +
1131 +
1109 1109  == 7.23 Set Packet Receiving Response Level ==
1110 1110  
1111 1111  
... ... @@ -1112,7 +1112,7 @@
1112 1112  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1113 1113  
1114 1114  
1115 -**RPL value:**
1138 +RPL value:
1116 1116  
1117 1117  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1118 1118  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1120,12 +1120,14 @@
1120 1120  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1121 1121  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1122 1122  
1123 -**Case Analyes:**
1124 1124  
1147 +Case Analyes:
1148 +
1125 1125  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1126 1126  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1127 1127  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1128 1128  
1153 +
1129 1129  (% style="color:blue" %)**AT Command: AT+RPL**
1130 1130  
1131 1131  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
... ... @@ -1142,25 +1142,23 @@
1142 1142  
1143 1143  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1144 1144  
1145 -* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1146 -* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1170 +* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1171 +* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1147 1147  
1173 +
1174 +
1148 1148  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1149 1149  
1150 1150  
1151 1151  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1152 1152  
1153 -(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1154 -|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1155 -|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1156 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1180 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1181 +|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1182 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1183 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1157 1157  OK
1158 1158  )))
1159 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1160 -value2: 0: uplink fcnt doesn't change for each NBTrans;
1161 -
1162 -1: uplink fcnt increase by 1 for each NBTrans.
1163 -)))|(% style="width:87px" %)(((
1186 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1164 1164  1
1165 1165  
1166 1166  OK
... ... @@ -1172,9 +1172,11 @@
1172 1172  
1173 1173  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1174 1174  
1175 -* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1176 -* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1198 +* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1199 +* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1177 1177  
1201 +
1202 +
1178 1178  == 7.25 Device offline rejoining （LWS007) ==
1179 1179  
1180 1180  
... ... @@ -1217,8 +1217,10 @@
1217 1217  
1218 1218  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1219 1219  
1220 -* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1245 +* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1221 1221  
1247 +
1248 +
1222 1222  == 7.26 Request the server to send an ACK ==
1223 1223  
1224 1224  
... ... @@ -1236,6 +1236,7 @@
1236 1236  OK
1237 1237  )))
1238 1238  
1266 +
1239 1239  == 7.27 Adjust network rejoining interval ==
1240 1240  
1241 1241  
... ... @@ -1259,17 +1259,22 @@
1259 1259  
1260 1260  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1261 1261  
1262 -* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1263 -* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1290 +* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1291 +* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1264 1264  
1293 +
1294 +
1265 1265  = 8. AT Commands Combination =
1266 1266  
1297 +
1267 1267  == 8.1 Set a fix RX2DR for downlink window ==
1268 1268  
1269 1269  
1270 -* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1271 -* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1301 +* **AT+ADR=0             ** **~-~->**  Disable ADR first
1302 +* **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1272 1272  
1304 +
1305 +
1273 1273  == 8.2 Use Downlink Command to set a fix uplink DR ==
1274 1274  
1275 1275  
... ... @@ -1277,8 +1277,6 @@
1277 1277  
1278 1278  **Same as:**
1279 1279  
1280 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1281 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1282 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1283 -
1284 -
1313 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1314 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1315 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0