Last modified by kai on 2024/09/06 10:00
<
From version < 52.11 >
edited by Xiaoling
on 2022/09/19 15:00
To version < 50.16 >
edited by Xiaoling
on 2022/07/13 13:47
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,14 +9,12 @@
9 9  
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 -* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
12 +* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
13 +* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 -
19 -
20 20  )))
21 21  
22 22  = 2. How to use AT Commands or Downlink command =
... ... @@ -30,7 +30,6 @@
30 30  
31 31  
32 32  
33 -
34 34  = 3. Support End Node and firmware version =
35 35  
36 36  
... ... @@ -106,8 +106,6 @@
106 106  )))
107 107  
108 108  
109 -
110 -
111 111  = 4. System Management Commands =
112 112  
113 113  
... ... @@ -140,15 +140,14 @@
140 140  )))
141 141  
142 142  (((
143 -If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
138 +If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
144 144  )))
145 145  
146 -* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
147 -* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
141 +* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
142 +* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
148 148  
149 149  
150 150  
151 -
152 152  == 4.2 Reboot End Node ==
153 153  
154 154  
... ... @@ -157,10 +157,10 @@
157 157  
158 158  (% style="color:blue" %)**AT Command: ATZ**
159 159  
160 -(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
161 -|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
162 -|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
163 -|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
154 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
155 +|=(% colspan="3" %)ATZ: Trig a reset of the MCU
156 +|**Command Example**|**Function**|**Response**
157 +|ATZ|Reset MCU|(((
164 164  Device reset and show booting info
165 165  
166 166  LSN50 Device/LoRa ST Module
... ... @@ -174,6 +174,7 @@
174 174  <followed by the Tx and Rx information>
175 175  )))
176 176  
171 +
177 177  (% style="color:blue" %)**Downlink Command: 0x04**
178 178  
179 179  (((
... ... @@ -183,7 +183,6 @@
183 183  (((
184 184  If the downlink payload=**04FF**, the end node will reboot.
185 185  
186 -
187 187  
188 188  )))
189 189  
... ... @@ -195,10 +195,10 @@
195 195  
196 196  (% style="color:blue" %)**AT Command: AT+FDR**
197 197  
198 -(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
199 -|=(% colspan="3" style="width: 786px;" %)Reset to factory default
200 -|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
201 -|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
192 +(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
193 +|=(% colspan="3" style="width: 828px;" %)Reset to factory default
194 +|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
195 +|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
202 202  Device reset to factory default parameters and show booting info
203 203  
204 204  LSN50 Device/LoRa ST Module
... ... @@ -212,6 +212,7 @@
212 212  Please set the parameters or reset Device to apply change
213 213  )))
214 214  
209 +
215 215  (% style="color:blue" %)**Downlink Command: 0x04**
216 216  
217 217  (((
... ... @@ -223,7 +223,6 @@
223 223  )))
224 224  
225 225  
226 -
227 227  == 4.4 Show Firmware Version ==
228 228  
229 229  
... ... @@ -232,15 +232,16 @@
232 232  
233 233  (% style="color:blue" %)**AT Command: AT+VER**
234 234  
235 -(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
236 -|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
237 -|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
238 -|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
229 +(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
230 +|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
231 +|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
232 +|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
239 239  1.3 EU868
240 240  
241 241  OK
242 242  )))
243 243  
238 +
244 244  (% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
245 245  
246 246  (((
... ... @@ -265,6 +265,7 @@
265 265  (((
266 266  
267 267  
263 +
268 268  **yy: Frequency Band:**
269 269  )))
270 270  
... ... @@ -282,6 +282,7 @@
282 282  (((
283 283  
284 284  
281 +
285 285  **zz: Subband**
286 286  )))
287 287  
... ... @@ -288,7 +288,6 @@
288 288  firmware version: v1.1.0 ~-~-> 110
289 289  
290 290  
291 -
292 292  == 4.5 Show System Configure ==
293 293  
294 294  
... ... @@ -316,7 +316,6 @@
316 316  
317 317  
318 318  
319 -
320 320  = 5. Keys, IDs and EUIs management =
321 321  
322 322  
... ... @@ -338,7 +338,6 @@
338 338  
339 339  
340 340  
341 -
342 342  == 5.2 Application Key ==
343 343  
344 344  
... ... @@ -357,7 +357,6 @@
357 357  
358 358  
359 359  
360 -
361 361  == 5.3 Application Session Key ==
362 362  
363 363  
... ... @@ -378,7 +378,6 @@
378 378  
379 379  
380 380  
381 -
382 382  == 5.4 Device Address ==
383 383  
384 384  
... ... @@ -399,7 +399,6 @@
399 399  
400 400  
401 401  
402 -
403 403  == 5.5 Device EUI ==
404 404  
405 405  
... ... @@ -420,7 +420,6 @@
420 420  
421 421  
422 422  
423 -
424 424  == 5.6 Network ID ==
425 425  
426 426  
... ... @@ -439,7 +439,6 @@
439 439  
440 440  
441 441  
442 -
443 443  == 5.7 Network Session Key ==
444 444  
445 445  
... ... @@ -458,7 +458,6 @@
458 458  
459 459  
460 460  
461 -
462 462  = 6. Joining and sending date on LoRaWAN network =
463 463  
464 464  
... ... @@ -483,7 +483,6 @@
483 483  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
484 484  
485 485  
486 -
487 487  (% style="color:blue" %)**Downlink Command: 0x05**
488 488  
489 489  Format: Command Code (0x05) followed by 2 bytes mode value.
... ... @@ -490,8 +490,8 @@
490 490  
491 491  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
492 492  
493 -* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
494 -* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
480 +* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
481 +* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
495 495  
496 496  
497 497  
... ... @@ -533,7 +533,6 @@
533 533  )))
534 534  
535 535  
536 -
537 537  (% style="color:blue" %)**Downlink Command: 0x05**
538 538  
539 539  Format: Command Code (0x05) followed by 2 bytes mode value.
... ... @@ -540,8 +540,8 @@
540 540  
541 541  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
542 542  
543 -* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
544 -* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
529 +* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
530 +* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
545 545  
546 546  
547 547  
... ... @@ -563,7 +563,6 @@
563 563  
564 564  
565 565  
566 -
567 567  == 6.3 Join LoRa® Network ==
568 568  
569 569  
... ... @@ -583,7 +583,6 @@
583 583  
584 584  
585 585  
586 -
587 587  == 6.4 LoRa® Network Join Mode ==
588 588  
589 589  
... ... @@ -602,7 +602,6 @@
602 602  |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
603 603  
604 604  
605 -
606 606  (% style="color:blue" %)**Downlink Command: 0x20**
607 607  
608 608  Format: Command Code (0x20) followed by 1 bytes mode value.
... ... @@ -609,8 +609,8 @@
609 609  
610 610  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
611 611  
612 -* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
613 -* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
595 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
596 +* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
614 614  
615 615  
616 616  
... ... @@ -632,7 +632,6 @@
632 632  
633 633  
634 634  
635 -
636 636  == 6.6 Print Last Received Data in Raw Format ==
637 637  
638 638  
... ... @@ -650,7 +650,6 @@
650 650  
651 651  
652 652  
653 -
654 654  == 6.7 Print Last Received Data in Binary Format ==
655 655  
656 656  
... ... @@ -668,7 +668,6 @@
668 668  
669 669  
670 670  
671 -
672 672  == 6.8 Send Text Data ==
673 673  
674 674  
... ... @@ -690,7 +690,6 @@
690 690  
691 691  
692 692  
693 -
694 694  == 6.9 Send Hexadecimal Data ==
695 695  
696 696  
... ... @@ -699,11 +699,11 @@
699 699  
700 700  (% style="color:blue" %)**AT Command: AT+SENDB**
701 701  
702 -(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
703 -|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
704 -|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
705 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
706 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
681 +(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
682 +|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
683 +|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
684 +|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
685 +|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
707 707  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
708 708  
709 709  
... ... @@ -711,7 +711,6 @@
711 711  
712 712  
713 713  
714 -
715 715  = 7. LoRaWAN network management =
716 716  
717 717  
... ... @@ -734,26 +734,23 @@
734 734  AT_PARAM_ERROR
735 735  )))
736 736  
715 +(% style="color:blue" %)**Downlink Command: 0x22**
737 737  
738 738  
739 -(% style="color:blue" %)**Downlink Command: 0x22**
740 740  
741 741  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
742 742  
743 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
744 -* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
721 +* **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
722 +* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
745 745  
746 -
747 -
748 -
749 749  == 7.2 LoRa® Class ==
750 750  
751 -
752 752  Feature: Get or Set the Device Class(Currently only support class A, class C).
753 753  
754 754  
755 -(% style="color:blue" %)**AT Command:  AT+CLASS**
729 +(% style="color:blue" %)**AT Command:AT+CLASS**
756 756  
731 +
757 757  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
758 758  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
759 759  |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
... ... @@ -764,16 +764,13 @@
764 764  
765 765  )))
766 766  
767 -
768 -
769 -
770 770  == 7.3 Duty Cycle Setting ==
771 771  
744 +Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
772 772  
773 -Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
774 774  
747 +(% style="color:blue" %)**AT Command:AT+DCS**
775 775  
776 -(% style="color:blue" %)**AT Command:  AT+DCS**
777 777  
778 778  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
779 779  |=(% colspan="3" style="width: 512px;" %)AT+DCS
... ... @@ -785,17 +785,14 @@
785 785  
786 786  )))
787 787  
788 -
789 -
790 -
791 791  == 7.4 Data Rate ==
792 792  
793 -
794 794  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
795 795  
796 796  
797 797  (% style="color:blue" %)**AT Command: AT+DR**
798 798  
767 +
799 799  (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
800 800  |=(% colspan="3" style="width: 463px;" %)AT+DR
801 801  |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -806,26 +806,23 @@
806 806  
807 807  )))
808 808  
778 +(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
809 809  
810 810  
811 -(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
812 812  
813 813  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
814 814  
815 -* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
816 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
784 +* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
785 +* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
817 817  
818 -
819 -
820 -
821 821  == 7.5 Frame Counter Downlink ==
822 822  
823 -
824 824  Feature: Get or Set the Frame Counter Downlink.
825 825  
826 826  
827 -(% style="color:blue" %)**AT Command:  AT+FCD**
792 +(% style="color:blue" %)**AT Command:AT+FCD**
828 828  
794 +
829 829  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
830 830  |=(% colspan="3" style="width: 690px;" %)AT+FCD
831 831  |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
... ... @@ -834,18 +834,18 @@
834 834  )))
835 835  |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
836 836  OK
803 +
804 +
837 837  )))
838 838  
839 -
840 -
841 -
842 842  == 7.6 Frame Counter Uplink ==
843 843  
844 844  Feature: Get or Set the Frame Counter Uplink.
845 845  
846 846  
847 -(% style="color:blue" %)**AT Command:  AT+FCU**
812 +(% style="color:blue" %)**AT Command:AT+FCU**
848 848  
814 +
849 849  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
850 850  |=(% colspan="3" style="width: 531px;" %)AT+FCU
851 851  |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -856,17 +856,14 @@
856 856  
857 857  )))
858 858  
859 -
860 -
861 -
862 862  == 7.7 Join Accept Delay1 ==
863 863  
864 -
865 865  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
866 866  
867 867  
868 -(% style="color:blue" %)**AT Command:  AT+JN1DL**
830 +(% style="color:blue" %)**AT Command:AT+JN1DL**
869 869  
832 +
870 870  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
871 871  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
872 872  |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -877,17 +877,14 @@
877 877  
878 878  )))
879 879  
880 -
881 -
882 -
883 883  == 7.8 Join Accept Delay2 ==
884 884  
885 -
886 886  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
887 887  
888 888  
889 -(% style="color:blue" %)**AT Command:  AT+JN2DL**
848 +(% style="color:blue" %)**AT Command:AT+JN2DL**
890 890  
850 +
891 891  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
892 892  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
893 893  |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
... ... @@ -898,19 +898,16 @@
898 898  
899 899  )))
900 900  
901 -
902 -
903 -
904 904  == 7.9 Public Network Mode ==
905 905  
906 -
907 907  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
908 908  
909 -(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
865 +Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
910 910  
911 911  
912 -(% style="color:blue" %)**AT Command:  AT+PNM**
868 +(% style="color:blue" %)**AT Command:AT+PNM**
913 913  
870 +
914 914  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
915 915  |=(% colspan="3" style="width: 664px;" %)AT+PNM
916 916  |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
... ... @@ -928,17 +928,14 @@
928 928  )))
929 929  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
930 930  
931 -
932 -
933 -
934 934  == 7.10 Receive Delay1 ==
935 935  
936 -
937 937  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
938 938  
939 939  
940 -(% style="color:blue" %)**AT Command: AT+RX1DL**
893 +(% style="color:blue" %)**AT Command:AT+RX1DL**
941 941  
895 +
942 942  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
943 943  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
944 944  |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -949,17 +949,14 @@
949 949  
950 950  )))
951 951  
952 -
953 -
954 -
955 955  == 7.11 Receive Delay2 ==
956 956  
957 -
958 958  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
959 959  
960 960  
961 -(% style="color:blue" %)**AT Command: AT+RX2DL**
911 +(% style="color:blue" %)**AT Command:AT+RX2DL**
962 962  
913 +
963 963  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
964 964  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
965 965  |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -970,17 +970,14 @@
970 970  
971 971  )))
972 972  
973 -
974 -
975 -
976 976  == 7.12 Rx2 Window Data Rate ==
977 977  
978 -
979 979  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
980 980  
981 981  
982 -(% style="color:blue" %)**AT Command:  AT+RX2DR**
929 +(% style="color:blue" %)**AT Command:AT+RX2DR**
983 983  
931 +
984 984  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
985 985  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
986 986  |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
... ... @@ -991,17 +991,14 @@
991 991  
992 992  )))
993 993  
994 -
995 -
996 -
997 997  == 7.13 Rx2 Window Frequency ==
998 998  
999 -
1000 1000  Feature: Get or Set the Rx2 window frequency
1001 1001  
1002 1002  
1003 -(% style="color:blue" %)**AT Command:  AT+RX2FQ**
947 +(% style="color:blue" %)**AT Command:AT+RX2FQ**
1004 1004  
949 +
1005 1005  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
1006 1006  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
1007 1007  |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
... ... @@ -1012,18 +1012,13 @@
1012 1012  
1013 1013  )))
1014 1014  
1015 -
1016 -
1017 -
1018 1018  == 7.14 Transmit Power ==
1019 1019  
1020 -
1021 1021  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
1022 1022  
1023 -(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
1024 1024  
965 +(% style="color:blue" %)**AT Command:AT+TXP**
1025 1025  
1026 -(% style="color:blue" %)**AT Command:  AT+TXP**
1027 1027  
1028 1028  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
1029 1029  |=(% colspan="3" style="width: 462px;" %)AT+TXP
... ... @@ -1039,20 +1039,17 @@
1039 1039  
1040 1040  If the downlink payload=22000100, it means setting the TXP to 0.
1041 1041  
1042 -* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
1043 -* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
982 +* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
983 +* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
1044 1044  
1045 -
1046 -
1047 -
1048 1048  == 7.15 RSSI of the Last Received Packet ==
1049 1049  
1050 -
1051 1051  Feature: Get or Set the Rx2 window frequency
1052 1052  
1053 1053  
1054 1054  (% style="color:blue" %)**AT Command:AT+RSSI**
1055 1055  
992 +
1056 1056  (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
1057 1057  |=(% colspan="3" style="width: 554px;" %)AT+RSSI
1058 1058  |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
... ... @@ -1060,17 +1060,14 @@
1060 1060  OK
1061 1061  )))
1062 1062  
1063 -
1064 -
1065 -
1066 1066  == 7.16 SNR of the Last Received Packet ==
1067 1067  
1068 -
1069 1069  Feature: Get the SNR of the last received packet
1070 1070  
1071 1071  
1072 -(% style="color:blue" %)**AT Command:  AT+SNR**
1005 +(% style="color:blue" %)**AT Command:AT+SNR**
1073 1073  
1007 +
1074 1074  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
1075 1075  |=(% colspan="3" style="width: 568px;" %)AT+SNR
1076 1076  |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -1078,17 +1078,14 @@
1078 1078  OK
1079 1079  )))
1080 1080  
1081 -
1082 -
1083 -
1084 1084  == 7.17 Application Port ==
1085 1085  
1086 -
1087 1087  Feature: Get or set the application port.
1088 1088  
1089 1089  
1090 1090  (% style="color:blue" %)**AT Command: AT+PORT**
1091 1091  
1022 +
1092 1092  (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
1093 1093  |=(% colspan="3" style="width: 497px;" %)AT+PORT
1094 1094  |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
... ... @@ -1097,28 +1097,24 @@
1097 1097  )))
1098 1098  |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
1099 1099  
1100 -
1101 -
1102 1102  (% style="color:blue" %)**Downlink Command: 0x23**
1103 1103  
1033 +
1104 1104  Format: Command Code (0x23) followed by 1 bytes port value.
1105 1105  
1106 1106  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1107 1107  
1108 -* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1109 -* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1038 +* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1039 +* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1110 1110  
1111 -
1112 -
1113 -
1114 1114  == 7.18 Single Channel Mode ==
1115 1115  
1116 -
1117 1117  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
1118 1118  
1119 1119  
1120 1120  (% style="color:blue" %)**AT Command: AT+CHS**
1121 1121  
1048 +
1122 1122  (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
1123 1123  |=(% colspan="3" style="width: 600px;" %)AT+CHS
1124 1124  |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -1127,17 +1127,14 @@
1127 1127  )))
1128 1128  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1129 1129  
1130 -
1131 -
1132 -
1133 1133  == 7.19 Eight Channel Mode ==
1134 1134  
1135 -
1136 1136  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1137 1137  
1138 1138  
1139 1139  (% style="color:blue" %)**AT Command: AT+CHE**
1140 1140  
1064 +
1141 1141  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1142 1142  |=(% colspan="3" style="width: 707px;" %)AT+CHE
1143 1143  |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
... ... @@ -1148,28 +1148,24 @@
1148 1148  )))
1149 1149  |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1150 1150  
1151 -
1152 -
1153 1153  (% style="color:blue" %)**Downlink Command: 0x24**
1154 1154  
1077 +
1155 1155  Format: Command Code (0x24) followed by 1 bytes channel value.
1156 1156  
1157 1157  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1158 1158  
1159 -* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1160 -* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1082 +* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1083 +* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1161 1161  
1162 -
1163 -
1164 -
1165 1165  == 7.20 Get or Set RXwindows1 timeout ==
1166 1166  
1087 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1167 1167  
1168 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1169 1169  
1170 -
1171 1171  (% style="color:blue" %)**AT Command: AT+RX1WTO**
1172 1172  
1092 +
1173 1173  (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1174 1174  |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1175 1175  |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
... ... @@ -1179,32 +1179,25 @@
1179 1179  |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1180 1180  
1181 1181  (((
1182 -
1183 -
1184 -
1185 -(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1186 -
1187 -
1102 +**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1188 1188  )))
1189 1189  
1190 1190  [[image:image-20220526162535-1.png]]
1191 1191  
1192 -
1193 1193  (((
1194 1194  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1195 1195  
1196 -
1197 1197  
1198 1198  )))
1199 1199  
1200 1200  == 7.21 Get or Set RXwindows2 timeout ==
1201 1201  
1115 +Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1202 1202  
1203 -Feature: Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1204 1204  
1205 -
1206 1206  (% style="color:blue" %)**AT Command: AT+RX2WTO**
1207 1207  
1120 +
1208 1208  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1209 1209  |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1210 1210  |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
... ... @@ -1213,17 +1213,14 @@
1213 1213  )))
1214 1214  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1215 1215  
1216 -
1217 -
1218 -
1219 1219  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1220 1220  
1221 -
1222 1222  Feature: Get or Set uplinkdwelltime
1223 1223  
1224 1224  
1225 1225  (% style="color:blue" %)**AT Command: AT+DWELLT**
1226 1226  
1136 +
1227 1227  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1228 1228  |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1229 1229  |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
... ... @@ -1232,28 +1232,22 @@
1232 1232  )))
1233 1233  |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1234 1234  
1235 -
1236 -
1237 1237  (% style="color:blue" %)**Downlink Command: 0x25**
1238 1238  
1147 +
1239 1239  Format: Command Code (0x25) followed by 1 bytes state value.
1240 1240  
1241 1241  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1242 1242  
1243 -* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1244 -* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1152 +* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1153 +* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1245 1245  
1246 -
1247 -
1248 -
1249 1249  == 7.23 Set Packet Receiving Response Level ==
1250 1250  
1251 -
1252 1252  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1253 1253  
1159 +RPL value:
1254 1254  
1255 -**RPL value:**
1256 -
1257 1257  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1258 1258  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1259 1259  * **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
... ... @@ -1260,17 +1260,15 @@
1260 1260  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1261 1261  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1262 1262  
1263 -**Case Analyes:**
1167 +Case Analyes:
1264 1264  
1265 1265  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1266 1266  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1267 1267  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1268 1268  
1269 -
1270 -
1271 -
1272 1272  (% style="color:blue" %)**AT Command: AT+RPL**
1273 1273  
1175 +
1274 1274  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1275 1275  |=(% colspan="3" style="width: 533px;" %)AT+RPL
1276 1276  |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
... ... @@ -1279,60 +1279,50 @@
1279 1279  )))
1280 1280  |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1281 1281  
1282 -
1283 -
1284 1284  (% style="color:blue" %)**Downlink Command: 0x21**
1285 1285  
1186 +
1286 1286  Format: Command Code (0x21) followed by 1 bytes level value.
1287 1287  
1288 1288  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1289 1289  
1290 -* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1291 -* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1191 +* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1192 +* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1292 1292  
1293 -
1294 -
1295 -
1296 1296  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1297 1297  
1298 1298  
1299 1299  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1300 1300  
1301 -(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1302 -|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1303 -|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1304 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1199 +
1200 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1201 +|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1202 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1203 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1305 1305  OK
1306 1306  )))
1307 -|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1308 -value2: 0: uplink fcnt doesn't change for each NBTrans;
1309 -
1310 -1: uplink fcnt increase by 1 for each NBTrans.
1311 -)))|(% style="width:87px" %)(((
1206 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1312 1312  1
1313 1313  
1314 1314  OK
1315 1315  )))
1316 1316  
1317 -
1318 -
1319 1319  (% style="color:blue" %)**Downlink Command: 0x33**
1320 1320  
1214 +
1321 1321  Format: Command Code (0x33) followed by 2 bytes mode value.
1322 1322  
1323 1323  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1324 1324  
1325 -* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1326 -* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1219 +* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1220 +* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1327 1327  
1328 -
1329 -
1330 -
1331 1331  == 7.25 Device offline rejoining （LWS007) ==
1332 1332  
1333 1333  
1334 1334  (% style="color:blue" %)**AT Command: AT+DDETECT**
1335 1335  
1227 +
1336 1336  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1337 1337  |=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1338 1338  |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
... ... @@ -1364,24 +1364,21 @@
1364 1364  OK
1365 1365  )))
1366 1366  
1367 -
1368 -
1369 1369  (% style="color:blue" %)**Downlink Command: 0x33**
1370 1370  
1261 +
1371 1371  Format: Command Code (0x32) followed by 2 bytes mode value.
1372 1372  
1373 1373  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1374 1374  
1375 -* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1266 +* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1376 1376  
1377 -
1378 -
1379 -
1380 1380  == 7.26 Request the server to send an ACK ==
1381 1381  
1382 1382  
1383 1383  (% style="color:blue" %)**AT Command: AT+PNACKMD**
1384 1384  
1273 +
1385 1385  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1386 1386  |=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1387 1387  |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
... ... @@ -1394,14 +1394,12 @@
1394 1394  OK
1395 1395  )))
1396 1396  
1397 -
1398 -
1399 -
1400 1400  == 7.27 Adjust network rejoining interval ==
1401 1401  
1402 1402  
1403 1403  (% style="color:blue" %)**AT Command: AT+RJTDC**
1404 1404  
1291 +
1405 1405  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1406 1406  |=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1407 1407  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
... ... @@ -1414,41 +1414,31 @@
1414 1414  Set the ReJoin data transmission interval to 60000ms = 60 seconds
1415 1415  )))
1416 1416  
1417 -
1418 -
1419 1419  (% style="color:blue" %)**Downlink Command: 0x26**
1420 1420  
1306 +
1421 1421  Format: Command Code (0x26) followed by 2 bytes mode value.
1422 1422  
1423 1423  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1424 1424  
1425 -* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1426 -* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1311 +* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1312 +* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1427 1427  
1428 -
1429 -
1430 -
1431 1431  = 8. AT Commands Combination =
1432 1432  
1433 -
1434 1434  == 8.1 Set a fix RX2DR for downlink window ==
1435 1435  
1318 +* **AT+ADR=0 **~-~-> Disable ADR first
1319 +* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1436 1436  
1437 -* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1438 -* (% style="color:red" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1439 -
1440 -
1441 -
1442 -
1443 1443  == 8.2 Use Downlink Command to set a fix uplink DR ==
1444 1444  
1445 1445  
1446 1446  (% style="color:blue" %)**Downlink Command: 0x22000500**
1447 1447  
1448 -**Same as:**
1449 1449  
1450 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1451 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1452 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1327 +Same as:
1453 1453  
1454 -
1329 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1330 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1331 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0