Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-XWiki.Edwin
	1	+XWiki.Xiaoling

Content

...	...	@@ -9,12 +9,14 @@
9	9
10	10	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11	11
12		-* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
13		-* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
	12	+* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
	13	+* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
14	14
15	15	(((
16	16	**This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17	17
	18	+
	19	+
18	18	)))
19	19
20	20	= 2. How to use AT Commands or Downlink command =
...	...	@@ -28,6 +28,7 @@
28	28
29	29
30	30
	33	+
31	31	= 3. Support End Node and firmware version =
32	32
33	33
...	...	@@ -104,6 +104,7 @@
104	104
105	105
106	106
	110	+
107	107	= 4. System Management Commands =
108	108
109	109
...	...	@@ -136,7 +136,7 @@
136	136	)))
137	137
138	138	(((
139		-If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
	143	+If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
140	140	)))
141	141
142	142	* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
...	...	@@ -144,6 +144,7 @@
144	144
145	145
146	146
	151	+
147	147	== 4.2 Reboot End Node ==
148	148
149	149
...	...	@@ -152,10 +152,10 @@
152	152
153	153	(% style="color:blue" %)**AT Command: ATZ**
154	154
155		-(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
156		-|=(% colspan="3" %)ATZ: Trig a reset of the MCU
157		-|**Command Example**|**Function**|**Response**
158		-|ATZ|Reset MCU|(((
	160	+(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
	161	+|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
	162	+|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
	163	+|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
159	159	Device reset and show booting info
160	160
161	161	LSN50 Device/LoRa ST Module
...	...	@@ -178,6 +178,7 @@
178	178	(((
179	179	If the downlink payload=**04FF**, the end node will reboot.
180	180
	186	+
181	181
182	182	)))
183	183
...	...	@@ -189,10 +189,10 @@
189	189
190	190	(% style="color:blue" %)**AT Command: AT+FDR**
191	191
192		-(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
193		-|=(% colspan="3" style="width: 828px;" %)Reset to factory default
194		-|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
195		-|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
	198	+(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
	199	+|=(% colspan="3" style="width: 786px;" %)Reset to factory default
	200	+|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
	201	+|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
196	196	Device reset to factory default parameters and show booting info
197	197
198	198	LSN50 Device/LoRa ST Module
...	...	@@ -217,6 +217,7 @@
217	217	)))
218	218
219	219
	226	+
220	220	== 4.4 Show Firmware Version ==
221	221
222	222
...	...	@@ -225,10 +225,10 @@
225	225
226	226	(% style="color:blue" %)**AT Command: AT+VER**
227	227
228		-(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
229		-|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
230		-|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
231		-|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
	235	+(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
	236	+|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
	237	+|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
	238	+|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
232	232	1.3 EU868
233	233
234	234	OK
...	...	@@ -281,6 +281,7 @@
281	281	firmware version: v1.1.0 ~-~-> 110
282	282
283	283
	291	+
284	284	== 4.5 Show System Configure ==
285	285
286	286
...	...	@@ -307,6 +307,8 @@
307	307	)))
308	308
309	309
	318	+
	319	+
310	310	= 5. Keys, IDs and EUIs management =
311	311
312	312
...	...	@@ -327,6 +327,8 @@
327	327	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
328	328
329	329
	340	+
	341	+
330	330	== 5.2 Application Key ==
331	331
332	332
...	...	@@ -344,6 +344,8 @@
344	344	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
345	345
346	346
	359	+
	360	+
347	347	== 5.3 Application Session Key ==
348	348
349	349
...	...	@@ -363,6 +363,8 @@
363	363	)))
364	364
365	365
	380	+
	381	+
366	366	== 5.4 Device Address ==
367	367
368	368
...	...	@@ -382,6 +382,8 @@
382	382	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
383	383
384	384
	401	+
	402	+
385	385	== 5.5 Device EUI ==
386	386
387	387
...	...	@@ -401,6 +401,8 @@
401	401	)))
402	402
403	403
	422	+
	423	+
404	404	== 5.6 Network ID ==
405	405
406	406
...	...	@@ -418,6 +418,8 @@
418	418	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
419	419
420	420
	441	+
	442	+
421	421	== 5.7 Network Session Key ==
422	422
423	423
...	...	@@ -435,6 +435,8 @@
435	435	|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
436	436
437	437
	460	+
	461	+
438	438	= 6. Joining and sending date on LoRaWAN network =
439	439
440	440
...	...	@@ -458,6 +458,8 @@
458	458	|(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
459	459	|(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
460	460
	485	+
	486	+
461	461	(% style="color:blue" %)**Downlink Command: 0x05**
462	462
463	463	Format: Command Code (0x05) followed by 2 bytes mode value.
...	...	@@ -469,6 +469,7 @@
469	469
470	470
471	471
	498	+
472	472	=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
473	473
474	474
...	...	@@ -505,6 +505,8 @@
505	505	OK
506	506	)))
507	507
	535	+
	536	+
508	508	(% style="color:blue" %)**Downlink Command: 0x05**
509	509
510	510	Format: Command Code (0x05) followed by 2 bytes mode value.
...	...	@@ -516,6 +516,7 @@
516	516
517	517
518	518
	548	+
519	519	== 6.2 Confirm Status ==
520	520
521	521
...	...	@@ -532,6 +532,8 @@
532	532	)))
533	533
534	534
	565	+
	566	+
535	535	== 6.3 Join LoRa® Network ==
536	536
537	537
...	...	@@ -550,6 +550,8 @@
550	550	)))
551	551
552	552
	585	+
	586	+
553	553	== 6.4 LoRa® Network Join Mode ==
554	554
555	555
...	...	@@ -567,6 +567,8 @@
567	567	|(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
568	568	|(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
569	569
	604	+
	605	+
570	570	(% style="color:blue" %)**Downlink Command: 0x20**
571	571
572	572	Format: Command Code (0x20) followed by 1 bytes mode value.
...	...	@@ -578,6 +578,7 @@
578	578
579	579
580	580
	617	+
581	581	== 6.5 LoRa® Network Join Status ==
582	582
583	583
...	...	@@ -594,6 +594,8 @@
594	594	)))
595	595
596	596
	634	+
	635	+
597	597	== 6.6 Print Last Received Data in Raw Format ==
598	598
599	599
...	...	@@ -610,6 +610,8 @@
610	610	)))
611	611
612	612
	652	+
	653	+
613	613	== 6.7 Print Last Received Data in Binary Format ==
614	614
615	615
...	...	@@ -626,6 +626,8 @@
626	626	)))
627	627
628	628
	670	+
	671	+
629	629	== 6.8 Send Text Data ==
630	630
631	631
...	...	@@ -646,6 +646,8 @@
646	646	)))
647	647
648	648
	692	+
	693	+
649	649	== 6.9 Send Hexadecimal Data ==
650	650
651	651
...	...	@@ -654,11 +654,11 @@
654	654
655	655	(% style="color:blue" %)**AT Command: AT+SENDB**
656	656
657		-(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
658		-|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
659		-|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
660		-|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
661		-|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
	702	+(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
	703	+|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
	704	+|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
	705	+|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
	706	+|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
662	662	AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
663	663
664	664
...	...	@@ -665,6 +665,8 @@
665	665	)))
666	666
667	667
	713	+
	714	+
668	668	= 7. LoRaWAN network management =
669	669
670	670
...	...	@@ -687,6 +687,8 @@
687	687	AT_PARAM_ERROR
688	688	)))
689	689
	737	+
	738	+
690	690	(% style="color:blue" %)**Downlink Command: 0x22**
691	691
692	692	If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
...	...	@@ -696,6 +696,7 @@
696	696
697	697
698	698
	748	+
699	699	== 7.2 LoRa® Class ==
700	700
701	701
...	...	@@ -702,7 +702,7 @@
702	702	Feature: Get or Set the Device Class(Currently only support class A, class C).
703	703
704	704
705		-(% style="color:blue" %)**AT Command:AT+CLASS**
	755	+(% style="color:blue" %)**AT Command:  AT+CLASS**
706	706
707	707	(% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
708	708	|=(% colspan="3" style="width: 504px;" %)AT+CLASS
...	...	@@ -715,13 +715,15 @@
715	715	)))
716	716
717	717
	768	+
	769	+
718	718	== 7.3 Duty Cycle Setting ==
719	719
720	720
721		-Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
	773	+Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
722	722
723	723
724		-(% style="color:blue" %)**AT Command:AT+DCS**
	776	+(% style="color:blue" %)**AT Command:  AT+DCS**
725	725
726	726	(% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
727	727	|=(% colspan="3" style="width: 512px;" %)AT+DCS
...	...	@@ -734,6 +734,8 @@
734	734	)))
735	735
736	736
	789	+
	790	+
737	737	== 7.4 Data Rate ==
738	738
739	739
...	...	@@ -752,6 +752,8 @@
752	752
753	753	)))
754	754
	809	+
	810	+
755	755	(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
756	756
757	757	If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
...	...	@@ -761,6 +761,7 @@
761	761
762	762
763	763
	820	+
764	764	== 7.5 Frame Counter Downlink ==
765	765
766	766
...	...	@@ -767,7 +767,7 @@
767	767	Feature: Get or Set the Frame Counter Downlink.
768	768
769	769
770		-(% style="color:blue" %)**AT Command:AT+FCD**
	827	+(% style="color:blue" %)**AT Command:  AT+FCD**
771	771
772	772	(% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
773	773	|=(% colspan="3" style="width: 690px;" %)AT+FCD
...	...	@@ -780,12 +780,14 @@
780	780	)))
781	781
782	782
	840	+
	841	+
783	783	== 7.6 Frame Counter Uplink ==
784	784
785	785	Feature: Get or Set the Frame Counter Uplink.
786	786
787	787
788		-(% style="color:blue" %)**AT Command:AT+FCU**
	847	+(% style="color:blue" %)**AT Command:  AT+FCU**
789	789
790	790	(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
791	791	|=(% colspan="3" style="width: 531px;" %)AT+FCU
...	...	@@ -798,6 +798,8 @@
798	798	)))
799	799
800	800
	860	+
	861	+
801	801	== 7.7 Join Accept Delay1 ==
802	802
803	803
...	...	@@ -804,7 +804,7 @@
804	804	Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
805	805
806	806
807		-(% style="color:blue" %)**AT Command:AT+JN1DL**
	868	+(% style="color:blue" %)**AT Command:  AT+JN1DL**
808	808
809	809	(% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
810	810	|=(% colspan="3" style="width: 534px;" %)AT+JN1DL
...	...	@@ -817,12 +817,15 @@
817	817	)))
818	818
819	819
	881	+
	882	+
820	820	== 7.8 Join Accept Delay2 ==
821	821
	885	+
822	822	Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
823	823
824	824
825		-(% style="color:blue" %)**AT Command:AT+JN2DL**
	889	+(% style="color:blue" %)**AT Command:  AT+JN2DL**
826	826
827	827	(% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
828	828	|=(% colspan="3" style="width: 535px;" %)AT+JN2DL
...	...	@@ -835,15 +835,17 @@
835	835	)))
836	836
837	837
	902	+
	903	+
838	838	== 7.9 Public Network Mode ==
839	839
840	840
841	841	Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
842	842
843		-(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
	909	+(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
844	844
845	845
846		-(% style="color:blue" %)**AT Command:AT+PNM**
	912	+(% style="color:blue" %)**AT Command:  AT+PNM**
847	847
848	848	(% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
849	849	|=(% colspan="3" style="width: 664px;" %)AT+PNM
...	...	@@ -863,6 +863,8 @@
863	863	|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
864	864
865	865
	932	+
	933	+
866	866	== 7.10 Receive Delay1 ==
867	867
868	868
...	...	@@ -869,7 +869,7 @@
869	869	Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
870	870
871	871
872		-(% style="color:blue" %)**AT Command:AT+RX1DL**
	940	+(% style="color:blue" %)**AT Command: AT+RX1DL**
873	873
874	874	(% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
875	875	|=(% colspan="3" style="width: 405px;" %)AT+RX1DL
...	...	@@ -882,6 +882,8 @@
882	882	)))
883	883
884	884
	953	+
	954	+
885	885	== 7.11 Receive Delay2 ==
886	886
887	887
...	...	@@ -888,7 +888,7 @@
888	888	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
889	889
890	890
891		-(% style="color:blue" %)**AT Command:AT+RX2DL**
	961	+(% style="color:blue" %)**AT Command: AT+RX2DL**
892	892
893	893	(% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
894	894	|=(% colspan="3" style="width: 478px;" %)AT+RX2DL
...	...	@@ -901,6 +901,8 @@
901	901	)))
902	902
903	903
	974	+
	975	+
904	904	== 7.12 Rx2 Window Data Rate ==
905	905
906	906
...	...	@@ -907,7 +907,7 @@
907	907	Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
908	908
909	909
910		-(% style="color:blue" %)**AT Command:AT+RX2DR**
	982	+(% style="color:blue" %)**AT Command:  AT+RX2DR**
911	911
912	912	(% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
913	913	|=(% colspan="3" style="width: 522px;" %)AT+RX2DR
...	...	@@ -920,6 +920,8 @@
920	920	)))
921	921
922	922
	995	+
	996	+
923	923	== 7.13 Rx2 Window Frequency ==
924	924
925	925
...	...	@@ -926,7 +926,7 @@
926	926	Feature: Get or Set the Rx2 window frequency
927	927
928	928
929		-(% style="color:blue" %)**AT Command:AT+RX2FQ**
	1003	+(% style="color:blue" %)**AT Command:  AT+RX2FQ**
930	930
931	931	(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
932	932	|=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
...	...	@@ -939,15 +939,17 @@
939	939	)))
940	940
941	941
	1016	+
	1017	+
942	942	== 7.14 Transmit Power ==
943	943
944	944
945	945	Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
946	946
947		-Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor
	1023	+(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
948	948
949	949
950		-(% style="color:blue" %)**AT Command:AT+TXP**
	1026	+(% style="color:blue" %)**AT Command:  AT+TXP**
951	951
952	952	(% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
953	953	|=(% colspan="3" style="width: 462px;" %)AT+TXP
...	...	@@ -968,6 +968,7 @@
968	968
969	969
970	970
	1047	+
971	971	== 7.15 RSSI of the Last Received Packet ==
972	972
973	973
...	...	@@ -984,6 +984,8 @@
984	984	)))
985	985
986	986
	1064	+
	1065	+
987	987	== 7.16 SNR of the Last Received Packet ==
988	988
989	989
...	...	@@ -990,7 +990,7 @@
990	990	Feature: Get the SNR of the last received packet
991	991
992	992
993		-(% style="color:blue" %)**AT Command:AT+SNR**
	1072	+(% style="color:blue" %)**AT Command:  AT+SNR**
994	994
995	995	(% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
996	996	|=(% colspan="3" style="width: 568px;" %)AT+SNR
...	...	@@ -1000,6 +1000,8 @@
1000	1000	)))
1001	1001
1002	1002
	1082	+
	1083	+
1003	1003	== 7.17 Application Port ==
1004	1004
1005	1005
...	...	@@ -1016,6 +1016,8 @@
1016	1016	)))
1017	1017	|(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
1018	1018
	1100	+
	1101	+
1019	1019	(% style="color:blue" %)**Downlink Command: 0x23**
1020	1020
1021	1021	Format: Command Code (0x23) followed by 1 bytes port value.
...	...	@@ -1026,6 +1026,8 @@
1026	1026	* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1027	1027
1028	1028
	1112	+
	1113	+
1029	1029	== 7.18 Single Channel Mode ==
1030	1030
1031	1031
...	...	@@ -1043,8 +1043,11 @@
1043	1043	|(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1044	1044
1045	1045
	1131	+
	1132	+
1046	1046	== 7.19 Eight Channel Mode ==
1047	1047
	1135	+
1048	1048	Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1049	1049
1050	1050
...	...	@@ -1060,6 +1060,8 @@
1060	1060	)))
1061	1061	|(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1062	1062
	1151	+
	1152	+
1063	1063	(% style="color:blue" %)**Downlink Command: 0x24**
1064	1064
1065	1065	Format: Command Code (0x24) followed by 1 bytes channel value.
...	...	@@ -1071,6 +1071,7 @@
1071	1071
1072	1072
1073	1073
	1164	+
1074	1074	== 7.20 Get or Set RXwindows1 timeout ==
1075	1075
1076	1076
...	...	@@ -1090,8 +1090,9 @@
1090	1090	(((
1091	1091
1092	1092
1093		-**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1094	1094
	1185	+(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
	1186	+
1095	1095
1096	1096	)))
1097	1097
...	...	@@ -1101,6 +1101,7 @@
1101	1101	(((
1102	1102	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1103	1103
	1196	+
1104	1104
1105	1105	)))
1106	1106
...	...	@@ -1121,6 +1121,8 @@
1121	1121	|(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1122	1122
1123	1123
	1217	+
	1218	+
1124	1124	== 7.22 Setting up uplinkdwelltime (as923, au915) ==
1125	1125
1126	1126
...	...	@@ -1137,6 +1137,8 @@
1137	1137	)))
1138	1138	|(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1139	1139
	1235	+
	1236	+
1140	1140	(% style="color:blue" %)**Downlink Command: 0x25**
1141	1141
1142	1142	Format: Command Code (0x25) followed by 1 bytes state value.
...	...	@@ -1148,6 +1148,7 @@
1148	1148
1149	1149
1150	1150
	1248	+
1151	1151	== 7.23 Set Packet Receiving Response Level ==
1152	1152
1153	1153
...	...	@@ -1168,6 +1168,9 @@
1168	1168	* For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1169	1169	* For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1170	1170
	1269	+
	1270	+
	1271	+
1171	1171	(% style="color:blue" %)**AT Command: AT+RPL**
1172	1172
1173	1173	(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
...	...	@@ -1178,6 +1178,8 @@
1178	1178	)))
1179	1179	|(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1180	1180
	1282	+
	1283	+
1181	1181	(% style="color:blue" %)**Downlink Command: 0x21**
1182	1182
1183	1183	Format: Command Code (0x21) followed by 1 bytes level value.
...	...	@@ -1189,6 +1189,7 @@
1189	1189
1190	1190
1191	1191
	1295	+
1192	1192	== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1193	1193
1194	1194
...	...	@@ -1210,6 +1210,8 @@
1210	1210	OK
1211	1211	)))
1212	1212
	1317	+
	1318	+
1213	1213	(% style="color:blue" %)**Downlink Command: 0x33**
1214	1214
1215	1215	Format: Command Code (0x33) followed by 2 bytes mode value.
...	...	@@ -1220,6 +1220,8 @@
1220	1220	* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1221	1221
1222	1222
	1329	+
	1330	+
1223	1223	== 7.25 Device offline rejoining （LWS007) ==
1224	1224
1225	1225
...	...	@@ -1256,6 +1256,8 @@
1256	1256	OK
1257	1257	)))
1258	1258
	1367	+
	1368	+
1259	1259	(% style="color:blue" %)**Downlink Command: 0x33**
1260	1260
1261	1261	Format: Command Code (0x32) followed by 2 bytes mode value.
...	...	@@ -1265,6 +1265,8 @@
1265	1265	* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1266	1266
1267	1267
	1378	+
	1379	+
1268	1268	== 7.26 Request the server to send an ACK ==
1269	1269
1270	1270
...	...	@@ -1283,6 +1283,8 @@
1283	1283	)))
1284	1284
1285	1285
	1398	+
	1399	+
1286	1286	== 7.27 Adjust network rejoining interval ==
1287	1287
1288	1288
...	...	@@ -1300,6 +1300,8 @@
1300	1300	Set the ReJoin data transmission interval to 60000ms = 60 seconds
1301	1301	)))
1302	1302
	1417	+
	1418	+
1303	1303	(% style="color:blue" %)**Downlink Command: 0x26**
1304	1304
1305	1305	Format: Command Code (0x26) followed by 2 bytes mode value.
...	...	@@ -1310,6 +1310,8 @@
1310	1310	* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1311	1311
1312	1312
	1429	+
	1430	+
1313	1313	= 8. AT Commands Combination =
1314	1314
1315	1315
...	...	@@ -1316,10 +1316,12 @@
1316	1316	== 8.1 Set a fix RX2DR for downlink window ==
1317	1317
1318	1318
1319		-* **AT+ADR=0             ** **~-~->**  Disable ADR first
1320		-* **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
	1437	+* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
	1438	+* (% style="color:red" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1321	1321
1322	1322
	1441	+
	1442	+
1323	1323	== 8.2 Use Downlink Command to set a fix uplink DR ==
1324	1324
1325	1325
...	...	@@ -1330,3 +1330,5 @@
1330	1330	* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1331	1331	* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1332	1332	* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1453	+
	1454	+