Last modified by kai on 2024/09/06 10:00
<
From version < 51.7 >
edited by Xiaoling
on 2022/07/13 14:12
To version < 52.11 >
edited by Xiaoling
on 2022/09/19 15:00
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,12 +9,14 @@
9 9  
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
13 -* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
12 +* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 +* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 +
19 +
18 18  )))
19 19  
20 20  = 2. How to use AT Commands or Downlink command =
... ... @@ -138,11 +138,11 @@
138 138  )))
139 139  
140 140  (((
141 -If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
143 +If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
142 142  )))
143 143  
144 -* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 -* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
147 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 146  
147 147  
148 148  
... ... @@ -155,10 +155,10 @@
155 155  
156 156  (% style="color:blue" %)**AT Command: ATZ**
157 157  
158 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
159 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU
160 -|**Command Example**|**Function**|**Response**
161 -|ATZ|Reset MCU|(((
160 +(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
161 +|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
162 +|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
163 +|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
162 162  Device reset and show booting info
163 163  
164 164  LSN50 Device/LoRa ST Module
... ... @@ -181,6 +181,7 @@
181 181  (((
182 182  If the downlink payload=**04FF**, the end node will reboot.
183 183  
186 +
184 184  
185 185  )))
186 186  
... ... @@ -192,10 +192,10 @@
192 192  
193 193  (% style="color:blue" %)**AT Command: AT+FDR**
194 194  
195 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
196 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default
197 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
198 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
198 +(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
199 +|=(% colspan="3" style="width: 786px;" %)Reset to factory default
200 +|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
201 +|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
199 199  Device reset to factory default parameters and show booting info
200 200  
201 201  LSN50 Device/LoRa ST Module
... ... @@ -220,6 +220,7 @@
220 220  )))
221 221  
222 222  
226 +
223 223  == 4.4 Show Firmware Version ==
224 224  
225 225  
... ... @@ -228,10 +228,10 @@
228 228  
229 229  (% style="color:blue" %)**AT Command: AT+VER**
230 230  
231 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
232 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
233 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
234 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
235 +(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
236 +|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
237 +|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
238 +|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
235 235  1.3 EU868
236 236  
237 237  OK
... ... @@ -284,6 +284,7 @@
284 284  firmware version: v1.1.0 ~-~-> 110
285 285  
286 286  
291 +
287 287  == 4.5 Show System Configure ==
288 288  
289 289  
... ... @@ -311,6 +311,7 @@
311 311  
312 312  
313 313  
319 +
314 314  = 5. Keys, IDs and EUIs management =
315 315  
316 316  
... ... @@ -332,6 +332,7 @@
332 332  
333 333  
334 334  
341 +
335 335  == 5.2 Application Key ==
336 336  
337 337  
... ... @@ -350,6 +350,7 @@
350 350  
351 351  
352 352  
360 +
353 353  == 5.3 Application Session Key ==
354 354  
355 355  
... ... @@ -370,6 +370,7 @@
370 370  
371 371  
372 372  
381 +
373 373  == 5.4 Device Address ==
374 374  
375 375  
... ... @@ -390,6 +390,7 @@
390 390  
391 391  
392 392  
402 +
393 393  == 5.5 Device EUI ==
394 394  
395 395  
... ... @@ -410,6 +410,7 @@
410 410  
411 411  
412 412  
423 +
413 413  == 5.6 Network ID ==
414 414  
415 415  
... ... @@ -428,6 +428,7 @@
428 428  
429 429  
430 430  
442 +
431 431  == 5.7 Network Session Key ==
432 432  
433 433  
... ... @@ -446,6 +446,7 @@
446 446  
447 447  
448 448  
461 +
449 449  = 6. Joining and sending date on LoRaWAN network =
450 450  
451 451  
... ... @@ -469,6 +469,8 @@
469 469  |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
470 470  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
471 471  
485 +
486 +
472 472  (% style="color:blue" %)**Downlink Command: 0x05**
473 473  
474 474  Format: Command Code (0x05) followed by 2 bytes mode value.
... ... @@ -475,8 +475,8 @@
475 475  
476 476  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
477 477  
478 -* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
479 -* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
493 +* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
494 +* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
480 480  
481 481  
482 482  
... ... @@ -517,6 +517,8 @@
517 517  OK
518 518  )))
519 519  
535 +
536 +
520 520  (% style="color:blue" %)**Downlink Command: 0x05**
521 521  
522 522  Format: Command Code (0x05) followed by 2 bytes mode value.
... ... @@ -523,10 +523,12 @@
523 523  
524 524  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
525 525  
526 -* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
527 -* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
543 +* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
544 +* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
528 528  
529 529  
547 +
548 +
530 530  == 6.2 Confirm Status ==
531 531  
532 532  
... ... @@ -542,6 +542,9 @@
542 542  OK
543 543  )))
544 544  
564 +
565 +
566 +
545 545  == 6.3 Join LoRa® Network ==
546 546  
547 547  
... ... @@ -559,6 +559,9 @@
559 559  While Error in format, return AT_BUSY_ERROR
560 560  )))
561 561  
584 +
585 +
586 +
562 562  == 6.4 LoRa® Network Join Mode ==
563 563  
564 564  
... ... @@ -576,6 +576,8 @@
576 576  |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
577 577  |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
578 578  
604 +
605 +
579 579  (% style="color:blue" %)**Downlink Command: 0x20**
580 580  
581 581  Format: Command Code (0x20) followed by 1 bytes mode value.
... ... @@ -582,10 +582,12 @@
582 582  
583 583  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
584 584  
585 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
586 -* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
612 +* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
613 +* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
587 587  
588 588  
616 +
617 +
589 589  == 6.5 LoRa® Network Join Status ==
590 590  
591 591  
... ... @@ -601,6 +601,9 @@
601 601  OK
602 602  )))
603 603  
633 +
634 +
635 +
604 604  == 6.6 Print Last Received Data in Raw Format ==
605 605  
606 606  
... ... @@ -616,6 +616,9 @@
616 616  OK
617 617  )))
618 618  
651 +
652 +
653 +
619 619  == 6.7 Print Last Received Data in Binary Format ==
620 620  
621 621  
... ... @@ -631,6 +631,9 @@
631 631  OK
632 632  )))
633 633  
669 +
670 +
671 +
634 634  == 6.8 Send Text Data ==
635 635  
636 636  
... ... @@ -650,6 +650,9 @@
650 650  
651 651  )))
652 652  
691 +
692 +
693 +
653 653  == 6.9 Send Hexadecimal Data ==
654 654  
655 655  
... ... @@ -658,16 +658,19 @@
658 658  
659 659  (% style="color:blue" %)**AT Command: AT+SENDB**
660 660  
661 -(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
662 -|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
663 -|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
664 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
665 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
702 +(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
703 +|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
704 +|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
705 +|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
706 +|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
666 666  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
667 667  
668 668  
669 669  )))
670 670  
712 +
713 +
714 +
671 671  = 7. LoRaWAN network management =
672 672  
673 673  
... ... @@ -690,14 +690,18 @@
690 690  AT_PARAM_ERROR
691 691  )))
692 692  
737 +
738 +
693 693  (% style="color:blue" %)**Downlink Command: 0x22**
694 694  
695 695  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
696 696  
697 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
698 -* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
743 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
744 +* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
699 699  
700 700  
747 +
748 +
701 701  == 7.2 LoRa® Class ==
702 702  
703 703  
... ... @@ -704,7 +704,7 @@
704 704  Feature: Get or Set the Device Class(Currently only support class A, class C).
705 705  
706 706  
707 -(% style="color:blue" %)**AT Command:AT+CLASS**
755 +(% style="color:blue" %)**AT Command:  AT+CLASS**
708 708  
709 709  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
710 710  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
... ... @@ -716,13 +716,16 @@
716 716  
717 717  )))
718 718  
767 +
768 +
769 +
719 719  == 7.3 Duty Cycle Setting ==
720 720  
721 721  
722 -Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
773 +Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
723 723  
724 724  
725 -(% style="color:blue" %)**AT Command:AT+DCS**
776 +(% style="color:blue" %)**AT Command:  AT+DCS**
726 726  
727 727  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
728 728  |=(% colspan="3" style="width: 512px;" %)AT+DCS
... ... @@ -734,6 +734,9 @@
734 734  
735 735  )))
736 736  
788 +
789 +
790 +
737 737  == 7.4 Data Rate ==
738 738  
739 739  
... ... @@ -752,14 +752,18 @@
752 752  
753 753  )))
754 754  
809 +
810 +
755 755  (% style="color:blue" %)**Downlink Command: 0x2200aaFF**
756 756  
757 757  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
758 758  
759 -* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
760 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
815 +* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
816 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
761 761  
762 762  
819 +
820 +
763 763  == 7.5 Frame Counter Downlink ==
764 764  
765 765  
... ... @@ -766,7 +766,7 @@
766 766  Feature: Get or Set the Frame Counter Downlink.
767 767  
768 768  
769 -(% style="color:blue" %)**AT Command:AT+FCD**
827 +(% style="color:blue" %)**AT Command:  AT+FCD**
770 770  
771 771  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
772 772  |=(% colspan="3" style="width: 690px;" %)AT+FCD
... ... @@ -778,12 +778,15 @@
778 778  OK
779 779  )))
780 780  
839 +
840 +
841 +
781 781  == 7.6 Frame Counter Uplink ==
782 782  
783 783  Feature: Get or Set the Frame Counter Uplink.
784 784  
785 785  
786 -(% style="color:blue" %)**AT Command:AT+FCU**
847 +(% style="color:blue" %)**AT Command:  AT+FCU**
787 787  
788 788  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
789 789  |=(% colspan="3" style="width: 531px;" %)AT+FCU
... ... @@ -795,6 +795,9 @@
795 795  
796 796  )))
797 797  
859 +
860 +
861 +
798 798  == 7.7 Join Accept Delay1 ==
799 799  
800 800  
... ... @@ -801,7 +801,7 @@
801 801  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
802 802  
803 803  
804 -(% style="color:blue" %)**AT Command:AT+JN1DL**
868 +(% style="color:blue" %)**AT Command:  AT+JN1DL**
805 805  
806 806  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
807 807  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
... ... @@ -813,12 +813,16 @@
813 813  
814 814  )))
815 815  
880 +
881 +
882 +
816 816  == 7.8 Join Accept Delay2 ==
817 817  
885 +
818 818  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
819 819  
820 820  
821 -(% style="color:blue" %)**AT Command:AT+JN2DL**
889 +(% style="color:blue" %)**AT Command:  AT+JN2DL**
822 822  
823 823  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
824 824  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
... ... @@ -830,15 +830,18 @@
830 830  
831 831  )))
832 832  
901 +
902 +
903 +
833 833  == 7.9 Public Network Mode ==
834 834  
835 835  
836 836  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
837 837  
838 -(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
909 +(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
839 839  
840 840  
841 -(% style="color:blue" %)**AT Command:AT+PNM**
912 +(% style="color:blue" %)**AT Command:  AT+PNM**
842 842  
843 843  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
844 844  |=(% colspan="3" style="width: 664px;" %)AT+PNM
... ... @@ -857,6 +857,9 @@
857 857  )))
858 858  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
859 859  
931 +
932 +
933 +
860 860  == 7.10 Receive Delay1 ==
861 861  
862 862  
... ... @@ -863,7 +863,7 @@
863 863  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
864 864  
865 865  
866 -(% style="color:blue" %)**AT Command:AT+RX1DL**
940 +(% style="color:blue" %)**AT Command: AT+RX1DL**
867 867  
868 868  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
869 869  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
... ... @@ -876,6 +876,8 @@
876 876  )))
877 877  
878 878  
953 +
954 +
879 879  == 7.11 Receive Delay2 ==
880 880  
881 881  
... ... @@ -882,7 +882,7 @@
882 882  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
883 883  
884 884  
885 -(% style="color:blue" %)**AT Command:AT+RX2DL**
961 +(% style="color:blue" %)**AT Command: AT+RX2DL**
886 886  
887 887  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
888 888  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
... ... @@ -895,6 +895,8 @@
895 895  )))
896 896  
897 897  
974 +
975 +
898 898  == 7.12 Rx2 Window Data Rate ==
899 899  
900 900  
... ... @@ -901,7 +901,7 @@
901 901  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
902 902  
903 903  
904 -(% style="color:blue" %)**AT Command:AT+RX2DR**
982 +(% style="color:blue" %)**AT Command:  AT+RX2DR**
905 905  
906 906  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
907 907  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
... ... @@ -914,6 +914,8 @@
914 914  )))
915 915  
916 916  
995 +
996 +
917 917  == 7.13 Rx2 Window Frequency ==
918 918  
919 919  
... ... @@ -920,7 +920,7 @@
920 920  Feature: Get or Set the Rx2 window frequency
921 921  
922 922  
923 -(% style="color:blue" %)**AT Command:AT+RX2FQ**
1003 +(% style="color:blue" %)**AT Command:  AT+RX2FQ**
924 924  
925 925  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
926 926  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
... ... @@ -933,14 +933,18 @@
933 933  )))
934 934  
935 935  
1016 +
1017 +
936 936  == 7.14 Transmit Power ==
937 937  
938 938  
939 939  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
940 940  
1023 +(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
941 941  
942 -(% style="color:blue" %)**AT Command:AT+TXP**
943 943  
1026 +(% style="color:blue" %)**AT Command:  AT+TXP**
1027 +
944 944  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
945 945  |=(% colspan="3" style="width: 462px;" %)AT+TXP
946 946  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -955,11 +955,12 @@
955 955  
956 956  If the downlink payload=22000100, it means setting the TXP to 0.
957 957  
958 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
959 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
1042 +* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
1043 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
960 960  
961 961  
962 962  
1047 +
963 963  == 7.15 RSSI of the Last Received Packet ==
964 964  
965 965  
... ... @@ -976,6 +976,8 @@
976 976  )))
977 977  
978 978  
1064 +
1065 +
979 979  == 7.16 SNR of the Last Received Packet ==
980 980  
981 981  
... ... @@ -982,7 +982,7 @@
982 982  Feature: Get the SNR of the last received packet
983 983  
984 984  
985 -(% style="color:blue" %)**AT Command:AT+SNR**
1072 +(% style="color:blue" %)**AT Command:  AT+SNR**
986 986  
987 987  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
988 988  |=(% colspan="3" style="width: 568px;" %)AT+SNR
... ... @@ -992,6 +992,8 @@
992 992  )))
993 993  
994 994  
1082 +
1083 +
995 995  == 7.17 Application Port ==
996 996  
997 997  
... ... @@ -1008,6 +1008,8 @@
1008 1008  )))
1009 1009  |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
1010 1010  
1100 +
1101 +
1011 1011  (% style="color:blue" %)**Downlink Command: 0x23**
1012 1012  
1013 1013  Format: Command Code (0x23) followed by 1 bytes port value.
... ... @@ -1014,11 +1014,12 @@
1014 1014  
1015 1015  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1016 1016  
1017 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1018 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1108 +* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1109 +* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1019 1019  
1020 1020  
1021 1021  
1113 +
1022 1022  == 7.18 Single Channel Mode ==
1023 1023  
1024 1024  
... ... @@ -1036,8 +1036,11 @@
1036 1036  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1037 1037  
1038 1038  
1131 +
1132 +
1039 1039  == 7.19 Eight Channel Mode ==
1040 1040  
1135 +
1041 1041  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1042 1042  
1043 1043  
... ... @@ -1053,6 +1053,8 @@
1053 1053  )))
1054 1054  |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1055 1055  
1151 +
1152 +
1056 1056  (% style="color:blue" %)**Downlink Command: 0x24**
1057 1057  
1058 1058  Format: Command Code (0x24) followed by 1 bytes channel value.
... ... @@ -1059,11 +1059,12 @@
1059 1059  
1060 1060  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1061 1061  
1062 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1063 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1159 +* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1160 +* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1064 1064  
1065 1065  
1066 1066  
1164 +
1067 1067  == 7.20 Get or Set RXwindows1 timeout ==
1068 1068  
1069 1069  
... ... @@ -1083,8 +1083,9 @@
1083 1083  (((
1084 1084  
1085 1085  
1086 -**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1087 1087  
1185 +(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1186 +
1088 1088  
1089 1089  )))
1090 1090  
... ... @@ -1094,6 +1094,7 @@
1094 1094  (((
1095 1095  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1096 1096  
1196 +
1097 1097  
1098 1098  )))
1099 1099  
... ... @@ -1114,6 +1114,8 @@
1114 1114  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1115 1115  
1116 1116  
1217 +
1218 +
1117 1117  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1118 1118  
1119 1119  
... ... @@ -1130,6 +1130,8 @@
1130 1130  )))
1131 1131  |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1132 1132  
1235 +
1236 +
1133 1133  (% style="color:blue" %)**Downlink Command: 0x25**
1134 1134  
1135 1135  Format: Command Code (0x25) followed by 1 bytes state value.
... ... @@ -1136,11 +1136,12 @@
1136 1136  
1137 1137  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1138 1138  
1139 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1140 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1243 +* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1244 +* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1141 1141  
1142 1142  
1143 1143  
1248 +
1144 1144  == 7.23 Set Packet Receiving Response Level ==
1145 1145  
1146 1146  
... ... @@ -1147,7 +1147,7 @@
1147 1147  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1148 1148  
1149 1149  
1150 -RPL value:
1255 +**RPL value:**
1151 1151  
1152 1152  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1153 1153  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1155,14 +1155,15 @@
1155 1155  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1156 1156  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1157 1157  
1263 +**Case Analyes:**
1158 1158  
1159 -Case Analyes:
1160 -
1161 1161  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1162 1162  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1163 1163  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1164 1164  
1165 1165  
1270 +
1271 +
1166 1166  (% style="color:blue" %)**AT Command: AT+RPL**
1167 1167  
1168 1168  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
... ... @@ -1173,6 +1173,8 @@
1173 1173  )))
1174 1174  |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1175 1175  
1282 +
1283 +
1176 1176  (% style="color:blue" %)**Downlink Command: 0x21**
1177 1177  
1178 1178  Format: Command Code (0x21) followed by 1 bytes level value.
... ... @@ -1179,28 +1179,35 @@
1179 1179  
1180 1180  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1181 1181  
1182 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1183 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1290 +* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1291 +* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1184 1184  
1185 1185  
1186 1186  
1295 +
1187 1187  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1188 1188  
1189 1189  
1190 1190  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1191 1191  
1192 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1193 -|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1194 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1195 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1301 +(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1302 +|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1303 +|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1304 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1196 1196  OK
1197 1197  )))
1198 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1307 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1308 +value2: 0: uplink fcnt doesn't change for each NBTrans;
1309 +
1310 +1: uplink fcnt increase by 1 for each NBTrans.
1311 +)))|(% style="width:87px" %)(((
1199 1199  1
1200 1200  
1201 1201  OK
1202 1202  )))
1203 1203  
1317 +
1318 +
1204 1204  (% style="color:blue" %)**Downlink Command: 0x33**
1205 1205  
1206 1206  Format: Command Code (0x33) followed by 2 bytes mode value.
... ... @@ -1207,11 +1207,12 @@
1207 1207  
1208 1208  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1209 1209  
1210 -* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1211 -* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1325 +* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1326 +* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1212 1212  
1213 1213  
1214 1214  
1330 +
1215 1215  == 7.25 Device offline rejoining （LWS007) ==
1216 1216  
1217 1217  
... ... @@ -1248,6 +1248,8 @@
1248 1248  OK
1249 1249  )))
1250 1250  
1367 +
1368 +
1251 1251  (% style="color:blue" %)**Downlink Command: 0x33**
1252 1252  
1253 1253  Format: Command Code (0x32) followed by 2 bytes mode value.
... ... @@ -1254,10 +1254,11 @@
1254 1254  
1255 1255  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1256 1256  
1257 -* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1375 +* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1258 1258  
1259 1259  
1260 1260  
1379 +
1261 1261  == 7.26 Request the server to send an ACK ==
1262 1262  
1263 1263  
... ... @@ -1276,6 +1276,8 @@
1276 1276  )))
1277 1277  
1278 1278  
1398 +
1399 +
1279 1279  == 7.27 Adjust network rejoining interval ==
1280 1280  
1281 1281  
... ... @@ -1293,6 +1293,8 @@
1293 1293  Set the ReJoin data transmission interval to 60000ms = 60 seconds
1294 1294  )))
1295 1295  
1417 +
1418 +
1296 1296  (% style="color:blue" %)**Downlink Command: 0x26**
1297 1297  
1298 1298  Format: Command Code (0x26) followed by 2 bytes mode value.
... ... @@ -1299,11 +1299,12 @@
1299 1299  
1300 1300  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1301 1301  
1302 -* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1303 -* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1425 +* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1426 +* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1304 1304  
1305 1305  
1306 1306  
1430 +
1307 1307  = 8. AT Commands Combination =
1308 1308  
1309 1309  
... ... @@ -1310,11 +1310,12 @@
1310 1310  == 8.1 Set a fix RX2DR for downlink window ==
1311 1311  
1312 1312  
1313 -* **AT+ADR=0             ** **~-~->**  Disable ADR first
1314 -* **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1437 +* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1438 +* (% style="color:red" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1315 1315  
1316 1316  
1317 1317  
1442 +
1318 1318  == 8.2 Use Downlink Command to set a fix uplink DR ==
1319 1319  
1320 1320  
... ... @@ -1322,6 +1322,8 @@
1322 1322  
1323 1323  **Same as:**
1324 1324  
1325 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1326 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1327 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1450 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1451 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1452 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1453 +
1454 +

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0