Last modified by kai on 2024/09/06 10:00
<
From version < 51.6 >
edited by Xiaoling
on 2022/07/13 14:11
To version < 52.5 >
edited by Xiaoling
on 2022/08/12 16:24
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -15,6 +15,8 @@
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 +
19 +
18 18  )))
19 19  
20 20  = 2. How to use AT Commands or Downlink command =
... ... @@ -28,7 +28,6 @@
28 28  
29 29  
30 30  
31 -
32 32  = 3. Support End Node and firmware version =
33 33  
34 34  
... ... @@ -141,12 +141,13 @@
141 141  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
142 142  )))
143 143  
144 -* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 -* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
145 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
146 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 146  
147 147  
148 148  
149 149  
151 +
150 150  == 4.2 Reboot End Node ==
151 151  
152 152  
... ... @@ -155,10 +155,10 @@
155 155  
156 156  (% style="color:blue" %)**AT Command: ATZ**
157 157  
158 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
159 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU
160 -|**Command Example**|**Function**|**Response**
161 -|ATZ|Reset MCU|(((
160 +(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
161 +|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
162 +|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
163 +|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
162 162  Device reset and show booting info
163 163  
164 164  LSN50 Device/LoRa ST Module
... ... @@ -181,6 +181,7 @@
181 181  (((
182 182  If the downlink payload=**04FF**, the end node will reboot.
183 183  
186 +
184 184  
185 185  )))
186 186  
... ... @@ -192,10 +192,10 @@
192 192  
193 193  (% style="color:blue" %)**AT Command: AT+FDR**
194 194  
195 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
196 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default
197 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
198 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
198 +(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
199 +|=(% colspan="3" style="width: 786px;" %)Reset to factory default
200 +|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
201 +|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
199 199  Device reset to factory default parameters and show booting info
200 200  
201 201  LSN50 Device/LoRa ST Module
... ... @@ -220,6 +220,7 @@
220 220  )))
221 221  
222 222  
226 +
223 223  == 4.4 Show Firmware Version ==
224 224  
225 225  
... ... @@ -228,10 +228,10 @@
228 228  
229 229  (% style="color:blue" %)**AT Command: AT+VER**
230 230  
231 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
232 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
233 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
234 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
235 +(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
236 +|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
237 +|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
238 +|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
235 235  1.3 EU868
236 236  
237 237  OK
... ... @@ -284,6 +284,7 @@
284 284  firmware version: v1.1.0 ~-~-> 110
285 285  
286 286  
291 +
287 287  == 4.5 Show System Configure ==
288 288  
289 289  
... ... @@ -311,6 +311,7 @@
311 311  
312 312  
313 313  
319 +
314 314  = 5. Keys, IDs and EUIs management =
315 315  
316 316  
... ... @@ -332,6 +332,7 @@
332 332  
333 333  
334 334  
341 +
335 335  == 5.2 Application Key ==
336 336  
337 337  
... ... @@ -350,6 +350,7 @@
350 350  
351 351  
352 352  
360 +
353 353  == 5.3 Application Session Key ==
354 354  
355 355  
... ... @@ -370,6 +370,7 @@
370 370  
371 371  
372 372  
381 +
373 373  == 5.4 Device Address ==
374 374  
375 375  
... ... @@ -390,6 +390,7 @@
390 390  
391 391  
392 392  
402 +
393 393  == 5.5 Device EUI ==
394 394  
395 395  
... ... @@ -408,6 +408,9 @@
408 408  OK
409 409  )))
410 410  
421 +
422 +
423 +
411 411  == 5.6 Network ID ==
412 412  
413 413  
... ... @@ -424,6 +424,9 @@
424 424  )))
425 425  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
426 426  
440 +
441 +
442 +
427 427  == 5.7 Network Session Key ==
428 428  
429 429  
... ... @@ -440,6 +440,9 @@
440 440  )))
441 441  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
442 442  
459 +
460 +
461 +
443 443  = 6. Joining and sending date on LoRaWAN network =
444 444  
445 445  
... ... @@ -469,8 +469,8 @@
469 469  
470 470  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
471 471  
472 -* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
473 -* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
491 +* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
492 +* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
474 474  
475 475  
476 476  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
... ... @@ -515,8 +515,8 @@
515 515  
516 516  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
517 517  
518 -* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
519 -* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
537 +* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
538 +* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
520 520  
521 521  
522 522  == 6.2 Confirm Status ==
... ... @@ -574,8 +574,8 @@
574 574  
575 575  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
576 576  
577 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
578 -* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
596 +* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
597 +* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
579 579  
580 580  
581 581  == 6.5 LoRa® Network Join Status ==
... ... @@ -686,10 +686,9 @@
686 686  
687 687  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
688 688  
689 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
690 -* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
708 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
709 +* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
691 691  
692 -
693 693  == 7.2 LoRa® Class ==
694 694  
695 695  
... ... @@ -748,10 +748,9 @@
748 748  
749 749  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
750 750  
751 -* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
752 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
769 +* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
770 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
753 753  
754 -
755 755  == 7.5 Frame Counter Downlink ==
756 756  
757 757  
... ... @@ -827,7 +827,7 @@
827 827  
828 828  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
829 829  
830 -(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
847 +(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
831 831  
832 832  
833 833  (% style="color:blue" %)**AT Command:AT+PNM**
... ... @@ -867,7 +867,6 @@
867 867  
868 868  )))
869 869  
870 -
871 871  == 7.11 Receive Delay2 ==
872 872  
873 873  
... ... @@ -886,7 +886,6 @@
886 886  
887 887  )))
888 888  
889 -
890 890  == 7.12 Rx2 Window Data Rate ==
891 891  
892 892  
... ... @@ -905,7 +905,6 @@
905 905  
906 906  )))
907 907  
908 -
909 909  == 7.13 Rx2 Window Frequency ==
910 910  
911 911  
... ... @@ -924,13 +924,14 @@
924 924  
925 925  )))
926 926  
927 -
928 928  == 7.14 Transmit Power ==
929 929  
930 930  
931 931  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
932 932  
946 +Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor
933 933  
948 +
934 934  (% style="color:blue" %)**AT Command:AT+TXP**
935 935  
936 936  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
... ... @@ -947,11 +947,10 @@
947 947  
948 948  If the downlink payload=22000100, it means setting the TXP to 0.
949 949  
950 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
951 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
965 +* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
966 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
952 952  
953 953  
954 -
955 955  == 7.15 RSSI of the Last Received Packet ==
956 956  
957 957  
... ... @@ -967,7 +967,6 @@
967 967  OK
968 968  )))
969 969  
970 -
971 971  == 7.16 SNR of the Last Received Packet ==
972 972  
973 973  
... ... @@ -983,7 +983,6 @@
983 983  OK
984 984  )))
985 985  
986 -
987 987  == 7.17 Application Port ==
988 988  
989 989  
... ... @@ -1006,11 +1006,10 @@
1006 1006  
1007 1007  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1008 1008  
1009 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1010 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1021 +* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1022 +* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1011 1011  
1012 1012  
1013 -
1014 1014  == 7.18 Single Channel Mode ==
1015 1015  
1016 1016  
... ... @@ -1027,9 +1027,9 @@
1027 1027  )))
1028 1028  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1029 1029  
1030 -
1031 1031  == 7.19 Eight Channel Mode ==
1032 1032  
1043 +
1033 1033  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1034 1034  
1035 1035  
... ... @@ -1051,11 +1051,10 @@
1051 1051  
1052 1052  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1053 1053  
1054 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1055 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1065 +* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1066 +* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1056 1056  
1057 1057  
1058 -
1059 1059  == 7.20 Get or Set RXwindows1 timeout ==
1060 1060  
1061 1061  
... ... @@ -1105,7 +1105,6 @@
1105 1105  )))
1106 1106  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1107 1107  
1108 -
1109 1109  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1110 1110  
1111 1111  
... ... @@ -1128,11 +1128,10 @@
1128 1128  
1129 1129  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1130 1130  
1131 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1132 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1140 +* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1141 +* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1133 1133  
1134 1134  
1135 -
1136 1136  == 7.23 Set Packet Receiving Response Level ==
1137 1137  
1138 1138  
... ... @@ -1139,7 +1139,7 @@
1139 1139  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1140 1140  
1141 1141  
1142 -RPL value:
1150 +**RPL value:**
1143 1143  
1144 1144  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1145 1145  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1147,14 +1147,12 @@
1147 1147  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1148 1148  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1149 1149  
1158 +**Case Analyes:**
1150 1150  
1151 -Case Analyes:
1152 -
1153 1153  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1154 1154  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1155 1155  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1156 1156  
1157 -
1158 1158  (% style="color:blue" %)**AT Command: AT+RPL**
1159 1159  
1160 1160  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
... ... @@ -1171,23 +1171,26 @@
1171 1171  
1172 1172  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1173 1173  
1174 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1175 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1180 +* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1181 +* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1176 1176  
1177 1177  
1178 -
1179 1179  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1180 1180  
1181 1181  
1182 1182  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1183 1183  
1184 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1185 -|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1186 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1187 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1189 +(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1190 +|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1191 +|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1192 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1188 1188  OK
1189 1189  )))
1190 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1195 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1196 +value2: 0: uplink fcnt doesn't change for each NBTrans;
1197 +
1198 +1: uplink fcnt increase by 1 for each NBTrans.
1199 +)))|(% style="width:87px" %)(((
1191 1191  1
1192 1192  
1193 1193  OK
... ... @@ -1199,11 +1199,10 @@
1199 1199  
1200 1200  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1201 1201  
1202 -* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1203 -* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1211 +* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1212 +* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1204 1204  
1205 1205  
1206 -
1207 1207  == 7.25 Device offline rejoining （LWS007) ==
1208 1208  
1209 1209  
... ... @@ -1246,10 +1246,9 @@
1246 1246  
1247 1247  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1248 1248  
1249 -* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1257 +* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1250 1250  
1251 1251  
1252 -
1253 1253  == 7.26 Request the server to send an ACK ==
1254 1254  
1255 1255  
... ... @@ -1267,7 +1267,6 @@
1267 1267  OK
1268 1268  )))
1269 1269  
1270 -
1271 1271  == 7.27 Adjust network rejoining interval ==
1272 1272  
1273 1273  
... ... @@ -1291,11 +1291,10 @@
1291 1291  
1292 1292  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1293 1293  
1294 -* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1295 -* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1300 +* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1301 +* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1296 1296  
1297 1297  
1298 -
1299 1299  = 8. AT Commands Combination =
1300 1300  
1301 1301  
... ... @@ -1306,7 +1306,6 @@
1306 1306  * **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1307 1307  
1308 1308  
1309 -
1310 1310  == 8.2 Use Downlink Command to set a fix uplink DR ==
1311 1311  
1312 1312  
... ... @@ -1314,6 +1314,8 @@
1314 1314  
1315 1315  **Same as:**
1316 1316  
1317 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1318 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1319 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1321 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1322 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1323 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1324 +
1325 +

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0