Last modified by kai on 2024/09/06 10:00
<
From version < 51.2 >
edited by Xiaoling
on 2022/07/13 14:04
To version < 52.9 >
edited by Xiaoling
on 2022/08/12 16:52
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -15,6 +15,8 @@
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 +
19 +
18 18  )))
19 19  
20 20  = 2. How to use AT Commands or Downlink command =
... ... @@ -28,7 +28,6 @@
28 28  
29 29  
30 30  
31 -
32 32  = 3. Support End Node and firmware version =
33 33  
34 34  
... ... @@ -141,9 +141,13 @@
141 141  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
142 142  )))
143 143  
144 -* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 -* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
145 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
146 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 146  
148 +
149 +
150 +
151 +
147 147  == 4.2 Reboot End Node ==
148 148  
149 149  
... ... @@ -152,10 +152,10 @@
152 152  
153 153  (% style="color:blue" %)**AT Command: ATZ**
154 154  
155 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
156 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU
157 -|**Command Example**|**Function**|**Response**
158 -|ATZ|Reset MCU|(((
160 +(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
161 +|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
162 +|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
163 +|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
159 159  Device reset and show booting info
160 160  
161 161  LSN50 Device/LoRa ST Module
... ... @@ -178,6 +178,7 @@
178 178  (((
179 179  If the downlink payload=**04FF**, the end node will reboot.
180 180  
186 +
181 181  
182 182  )))
183 183  
... ... @@ -189,10 +189,10 @@
189 189  
190 190  (% style="color:blue" %)**AT Command: AT+FDR**
191 191  
192 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
193 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default
194 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
195 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
198 +(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
199 +|=(% colspan="3" style="width: 786px;" %)Reset to factory default
200 +|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
201 +|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
196 196  Device reset to factory default parameters and show booting info
197 197  
198 198  LSN50 Device/LoRa ST Module
... ... @@ -217,6 +217,7 @@
217 217  )))
218 218  
219 219  
226 +
220 220  == 4.4 Show Firmware Version ==
221 221  
222 222  
... ... @@ -225,10 +225,10 @@
225 225  
226 226  (% style="color:blue" %)**AT Command: AT+VER**
227 227  
228 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
229 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
230 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
231 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
235 +(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
236 +|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
237 +|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
238 +|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
232 232  1.3 EU868
233 233  
234 234  OK
... ... @@ -258,7 +258,6 @@
258 258  (((
259 259  
260 260  
261 -
262 262  **yy: Frequency Band:**
263 263  )))
264 264  
... ... @@ -276,7 +276,6 @@
276 276  (((
277 277  
278 278  
279 -
280 280  **zz: Subband**
281 281  )))
282 282  
... ... @@ -283,6 +283,7 @@
283 283  firmware version: v1.1.0 ~-~-> 110
284 284  
285 285  
291 +
286 286  == 4.5 Show System Configure ==
287 287  
288 288  
... ... @@ -308,6 +308,9 @@
308 308  OK
309 309  )))
310 310  
317 +
318 +
319 +
311 311  = 5. Keys, IDs and EUIs management =
312 312  
313 313  
... ... @@ -327,6 +327,9 @@
327 327  )))
328 328  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
329 329  
339 +
340 +
341 +
330 330  == 5.2 Application Key ==
331 331  
332 332  
... ... @@ -343,6 +343,9 @@
343 343  )))
344 344  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
345 345  
358 +
359 +
360 +
346 346  == 5.3 Application Session Key ==
347 347  
348 348  
... ... @@ -361,6 +361,9 @@
361 361  OK
362 362  )))
363 363  
379 +
380 +
381 +
364 364  == 5.4 Device Address ==
365 365  
366 366  
... ... @@ -379,6 +379,9 @@
379 379  )))
380 380  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
381 381  
400 +
401 +
402 +
382 382  == 5.5 Device EUI ==
383 383  
384 384  
... ... @@ -397,6 +397,9 @@
397 397  OK
398 398  )))
399 399  
421 +
422 +
423 +
400 400  == 5.6 Network ID ==
401 401  
402 402  
... ... @@ -413,6 +413,9 @@
413 413  )))
414 414  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
415 415  
440 +
441 +
442 +
416 416  == 5.7 Network Session Key ==
417 417  
418 418  
... ... @@ -429,6 +429,9 @@
429 429  )))
430 430  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
431 431  
459 +
460 +
461 +
432 432  = 6. Joining and sending date on LoRaWAN network =
433 433  
434 434  
... ... @@ -458,10 +458,12 @@
458 458  
459 459  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
460 460  
461 -* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
462 -* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
491 +* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
492 +* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
463 463  
464 464  
495 +
496 +
465 465  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
466 466  
467 467  
... ... @@ -504,10 +504,12 @@
504 504  
505 505  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
506 506  
507 -* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
508 -* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
539 +* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
540 +* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
509 509  
510 510  
543 +
544 +
511 511  == 6.2 Confirm Status ==
512 512  
513 513  
... ... @@ -523,6 +523,9 @@
523 523  OK
524 524  )))
525 525  
560 +
561 +
562 +
526 526  == 6.3 Join LoRa® Network ==
527 527  
528 528  
... ... @@ -540,6 +540,9 @@
540 540  While Error in format, return AT_BUSY_ERROR
541 541  )))
542 542  
580 +
581 +
582 +
543 543  == 6.4 LoRa® Network Join Mode ==
544 544  
545 545  
... ... @@ -563,10 +563,12 @@
563 563  
564 564  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
565 565  
566 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
567 -* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
606 +* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
607 +* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
568 568  
569 569  
610 +
611 +
570 570  == 6.5 LoRa® Network Join Status ==
571 571  
572 572  
... ... @@ -582,6 +582,9 @@
582 582  OK
583 583  )))
584 584  
627 +
628 +
629 +
585 585  == 6.6 Print Last Received Data in Raw Format ==
586 586  
587 587  
... ... @@ -597,6 +597,9 @@
597 597  OK
598 598  )))
599 599  
645 +
646 +
647 +
600 600  == 6.7 Print Last Received Data in Binary Format ==
601 601  
602 602  
... ... @@ -612,6 +612,9 @@
612 612  OK
613 613  )))
614 614  
663 +
664 +
665 +
615 615  == 6.8 Send Text Data ==
616 616  
617 617  
... ... @@ -631,6 +631,9 @@
631 631  
632 632  )))
633 633  
685 +
686 +
687 +
634 634  == 6.9 Send Hexadecimal Data ==
635 635  
636 636  
... ... @@ -649,6 +649,9 @@
649 649  
650 650  )))
651 651  
706 +
707 +
708 +
652 652  = 7. LoRaWAN network management =
653 653  
654 654  
... ... @@ -675,10 +675,13 @@
675 675  
676 676  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
677 677  
678 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
679 -* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
735 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
736 +* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
680 680  
681 681  
739 +
740 +
741 +
682 682  == 7.2 LoRa® Class ==
683 683  
684 684  
... ... @@ -697,6 +697,9 @@
697 697  
698 698  )))
699 699  
760 +
761 +
762 +
700 700  == 7.3 Duty Cycle Setting ==
701 701  
702 702  
... ... @@ -715,6 +715,9 @@
715 715  
716 716  )))
717 717  
781 +
782 +
783 +
718 718  == 7.4 Data Rate ==
719 719  
720 720  
... ... @@ -737,10 +737,13 @@
737 737  
738 738  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
739 739  
740 -* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
741 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
806 +* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
807 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
742 742  
743 743  
810 +
811 +
812 +
744 744  == 7.5 Frame Counter Downlink ==
745 745  
746 746  
... ... @@ -759,6 +759,9 @@
759 759  OK
760 760  )))
761 761  
831 +
832 +
833 +
762 762  == 7.6 Frame Counter Uplink ==
763 763  
764 764  Feature: Get or Set the Frame Counter Uplink.
... ... @@ -776,6 +776,9 @@
776 776  
777 777  )))
778 778  
851 +
852 +
853 +
779 779  == 7.7 Join Accept Delay1 ==
780 780  
781 781  
... ... @@ -794,6 +794,9 @@
794 794  
795 795  )))
796 796  
872 +
873 +
874 +
797 797  == 7.8 Join Accept Delay2 ==
798 798  
799 799  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
... ... @@ -811,12 +811,15 @@
811 811  
812 812  )))
813 813  
892 +
893 +
894 +
814 814  == 7.9 Public Network Mode ==
815 815  
816 816  
817 817  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
818 818  
819 -(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
900 +(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
820 820  
821 821  
822 822  (% style="color:blue" %)**AT Command:AT+PNM**
... ... @@ -838,6 +838,9 @@
838 838  )))
839 839  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
840 840  
922 +
923 +
924 +
841 841  == 7.10 Receive Delay1 ==
842 842  
843 843  
... ... @@ -857,6 +857,8 @@
857 857  )))
858 858  
859 859  
944 +
945 +
860 860  == 7.11 Receive Delay2 ==
861 861  
862 862  
... ... @@ -876,6 +876,8 @@
876 876  )))
877 877  
878 878  
965 +
966 +
879 879  == 7.12 Rx2 Window Data Rate ==
880 880  
881 881  
... ... @@ -895,6 +895,8 @@
895 895  )))
896 896  
897 897  
986 +
987 +
898 898  == 7.13 Rx2 Window Frequency ==
899 899  
900 900  
... ... @@ -914,12 +914,16 @@
914 914  )))
915 915  
916 916  
1007 +
1008 +
917 917  == 7.14 Transmit Power ==
918 918  
919 919  
920 920  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
921 921  
1014 +Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor
922 922  
1016 +
923 923  (% style="color:blue" %)**AT Command:AT+TXP**
924 924  
925 925  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
... ... @@ -936,11 +936,12 @@
936 936  
937 937  If the downlink payload=22000100, it means setting the TXP to 0.
938 938  
939 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
940 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
1033 +* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
1034 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
941 941  
942 942  
943 943  
1038 +
944 944  == 7.15 RSSI of the Last Received Packet ==
945 945  
946 946  
... ... @@ -957,6 +957,8 @@
957 957  )))
958 958  
959 959  
1055 +
1056 +
960 960  == 7.16 SNR of the Last Received Packet ==
961 961  
962 962  
... ... @@ -973,6 +973,8 @@
973 973  )))
974 974  
975 975  
1073 +
1074 +
976 976  == 7.17 Application Port ==
977 977  
978 978  
... ... @@ -995,11 +995,10 @@
995 995  
996 996  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
997 997  
998 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
999 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1097 +* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1098 +* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1000 1000  
1001 1001  
1002 -
1003 1003  == 7.18 Single Channel Mode ==
1004 1004  
1005 1005  
... ... @@ -1016,9 +1016,9 @@
1016 1016  )))
1017 1017  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1018 1018  
1019 -
1020 1020  == 7.19 Eight Channel Mode ==
1021 1021  
1119 +
1022 1022  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1023 1023  
1024 1024  
... ... @@ -1040,11 +1040,10 @@
1040 1040  
1041 1041  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1042 1042  
1043 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1044 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1141 +* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1142 +* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1045 1045  
1046 1046  
1047 -
1048 1048  == 7.20 Get or Set RXwindows1 timeout ==
1049 1049  
1050 1050  
... ... @@ -1094,7 +1094,6 @@
1094 1094  )))
1095 1095  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1096 1096  
1097 -
1098 1098  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1099 1099  
1100 1100  
... ... @@ -1117,11 +1117,10 @@
1117 1117  
1118 1118  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1119 1119  
1120 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1121 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1216 +* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1217 +* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1122 1122  
1123 1123  
1124 -
1125 1125  == 7.23 Set Packet Receiving Response Level ==
1126 1126  
1127 1127  
... ... @@ -1128,7 +1128,7 @@
1128 1128  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1129 1129  
1130 1130  
1131 -RPL value:
1226 +**RPL value:**
1132 1132  
1133 1133  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1134 1134  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1136,14 +1136,12 @@
1136 1136  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1137 1137  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1138 1138  
1234 +**Case Analyes:**
1139 1139  
1140 -Case Analyes:
1141 -
1142 1142  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1143 1143  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1144 1144  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1145 1145  
1146 -
1147 1147  (% style="color:blue" %)**AT Command: AT+RPL**
1148 1148  
1149 1149  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
... ... @@ -1160,23 +1160,26 @@
1160 1160  
1161 1161  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1162 1162  
1163 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1164 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1256 +* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1257 +* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1165 1165  
1166 1166  
1167 -
1168 1168  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1169 1169  
1170 1170  
1171 1171  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1172 1172  
1173 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1174 -|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1175 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1176 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1265 +(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1266 +|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1267 +|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1268 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1177 1177  OK
1178 1178  )))
1179 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1271 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1272 +value2: 0: uplink fcnt doesn't change for each NBTrans;
1273 +
1274 +1: uplink fcnt increase by 1 for each NBTrans.
1275 +)))|(% style="width:87px" %)(((
1180 1180  1
1181 1181  
1182 1182  OK
... ... @@ -1188,11 +1188,10 @@
1188 1188  
1189 1189  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1190 1190  
1191 -* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1192 -* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1287 +* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1288 +* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1193 1193  
1194 1194  
1195 -
1196 1196  == 7.25 Device offline rejoining （LWS007) ==
1197 1197  
1198 1198  
... ... @@ -1235,10 +1235,9 @@
1235 1235  
1236 1236  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1237 1237  
1238 -* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1333 +* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1239 1239  
1240 1240  
1241 -
1242 1242  == 7.26 Request the server to send an ACK ==
1243 1243  
1244 1244  
... ... @@ -1256,7 +1256,6 @@
1256 1256  OK
1257 1257  )))
1258 1258  
1259 -
1260 1260  == 7.27 Adjust network rejoining interval ==
1261 1261  
1262 1262  
... ... @@ -1280,11 +1280,10 @@
1280 1280  
1281 1281  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1282 1282  
1283 -* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1284 -* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1376 +* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1377 +* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1285 1285  
1286 1286  
1287 -
1288 1288  = 8. AT Commands Combination =
1289 1289  
1290 1290  
... ... @@ -1295,7 +1295,6 @@
1295 1295  * **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1296 1296  
1297 1297  
1298 -
1299 1299  == 8.2 Use Downlink Command to set a fix uplink DR ==
1300 1300  
1301 1301  
... ... @@ -1303,6 +1303,8 @@
1303 1303  
1304 1304  **Same as:**
1305 1305  
1306 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1307 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1308 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1397 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1398 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1399 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1400 +
1401 +

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0