Last modified by kai on 2024/09/06 10:00
<
From version < 51.17 >
edited by Xiaoling
on 2022/07/13 14:14
To version < 52.4 >
edited by Xiaoling
on 2022/08/12 15:58
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -15,6 +15,8 @@
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 +
19 +
18 18  )))
19 19  
20 20  = 2. How to use AT Commands or Downlink command =
... ... @@ -28,7 +28,6 @@
28 28  
29 29  
30 30  
31 -
32 32  = 3. Support End Node and firmware version =
33 33  
34 34  
... ... @@ -141,12 +141,13 @@
141 141  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
142 142  )))
143 143  
144 -* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 -* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
145 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
146 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 146  
147 147  
148 148  
149 149  
151 +
150 150  == 4.2 Reboot End Node ==
151 151  
152 152  
... ... @@ -155,10 +155,10 @@
155 155  
156 156  (% style="color:blue" %)**AT Command: ATZ**
157 157  
158 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
159 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU
160 -|**Command Example**|**Function**|**Response**
161 -|ATZ|Reset MCU|(((
160 +(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
161 +|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
162 +|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
163 +|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
162 162  Device reset and show booting info
163 163  
164 164  LSN50 Device/LoRa ST Module
... ... @@ -181,6 +181,7 @@
181 181  (((
182 182  If the downlink payload=**04FF**, the end node will reboot.
183 183  
186 +
184 184  
185 185  )))
186 186  
... ... @@ -192,10 +192,10 @@
192 192  
193 193  (% style="color:blue" %)**AT Command: AT+FDR**
194 194  
195 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
196 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default
197 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
198 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
198 +(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
199 +|=(% colspan="3" style="width: 786px;" %)Reset to factory default
200 +|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
201 +|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
199 199  Device reset to factory default parameters and show booting info
200 200  
201 201  LSN50 Device/LoRa ST Module
... ... @@ -220,6 +220,7 @@
220 220  )))
221 221  
222 222  
226 +
223 223  == 4.4 Show Firmware Version ==
224 224  
225 225  
... ... @@ -228,10 +228,10 @@
228 228  
229 229  (% style="color:blue" %)**AT Command: AT+VER**
230 230  
231 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
232 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
233 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
234 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
235 +(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
236 +|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
237 +|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
238 +|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
235 235  1.3 EU868
236 236  
237 237  OK
... ... @@ -284,6 +284,7 @@
284 284  firmware version: v1.1.0 ~-~-> 110
285 285  
286 286  
291 +
287 287  == 4.5 Show System Configure ==
288 288  
289 289  
... ... @@ -311,6 +311,7 @@
311 311  
312 312  
313 313  
319 +
314 314  = 5. Keys, IDs and EUIs management =
315 315  
316 316  
... ... @@ -332,6 +332,7 @@
332 332  
333 333  
334 334  
341 +
335 335  == 5.2 Application Key ==
336 336  
337 337  
... ... @@ -350,6 +350,7 @@
350 350  
351 351  
352 352  
360 +
353 353  == 5.3 Application Session Key ==
354 354  
355 355  
... ... @@ -370,6 +370,7 @@
370 370  
371 371  
372 372  
381 +
373 373  == 5.4 Device Address ==
374 374  
375 375  
... ... @@ -390,6 +390,7 @@
390 390  
391 391  
392 392  
402 +
393 393  == 5.5 Device EUI ==
394 394  
395 395  
... ... @@ -408,8 +408,6 @@
408 408  OK
409 409  )))
410 410  
411 -
412 -
413 413  == 5.6 Network ID ==
414 414  
415 415  
... ... @@ -426,8 +426,6 @@
426 426  )))
427 427  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
428 428  
429 -
430 -
431 431  == 5.7 Network Session Key ==
432 432  
433 433  
... ... @@ -444,8 +444,6 @@
444 444  )))
445 445  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
446 446  
447 -
448 -
449 449  = 6. Joining and sending date on LoRaWAN network =
450 450  
451 451  
... ... @@ -475,12 +475,10 @@
475 475  
476 476  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
477 477  
478 -* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
479 -* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
482 +* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
483 +* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
480 480  
481 481  
482 -
483 -
484 484  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
485 485  
486 486  
... ... @@ -523,12 +523,10 @@
523 523  
524 524  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
525 525  
526 -* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
527 -* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
528 +* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
529 +* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
528 528  
529 529  
530 -
531 -
532 532  == 6.2 Confirm Status ==
533 533  
534 534  
... ... @@ -544,8 +544,6 @@
544 544  OK
545 545  )))
546 546  
547 -
548 -
549 549  == 6.3 Join LoRa® Network ==
550 550  
551 551  
... ... @@ -563,8 +563,6 @@
563 563  While Error in format, return AT_BUSY_ERROR
564 564  )))
565 565  
566 -
567 -
568 568  == 6.4 LoRa® Network Join Mode ==
569 569  
570 570  
... ... @@ -588,12 +588,10 @@
588 588  
589 589  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
590 590  
591 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
592 -* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
587 +* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
588 +* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
593 593  
594 594  
595 -
596 -
597 597  == 6.5 LoRa® Network Join Status ==
598 598  
599 599  
... ... @@ -609,8 +609,6 @@
609 609  OK
610 610  )))
611 611  
612 -
613 -
614 614  == 6.6 Print Last Received Data in Raw Format ==
615 615  
616 616  
... ... @@ -626,8 +626,6 @@
626 626  OK
627 627  )))
628 628  
629 -
630 -
631 631  == 6.7 Print Last Received Data in Binary Format ==
632 632  
633 633  
... ... @@ -643,8 +643,6 @@
643 643  OK
644 644  )))
645 645  
646 -
647 -
648 648  == 6.8 Send Text Data ==
649 649  
650 650  
... ... @@ -664,8 +664,6 @@
664 664  
665 665  )))
666 666  
667 -
668 -
669 669  == 6.9 Send Hexadecimal Data ==
670 670  
671 671  
... ... @@ -684,8 +684,6 @@
684 684  
685 685  )))
686 686  
687 -
688 -
689 689  = 7. LoRaWAN network management =
690 690  
691 691  
... ... @@ -708,17 +708,13 @@
708 708  AT_PARAM_ERROR
709 709  )))
710 710  
711 -
712 712  (% style="color:blue" %)**Downlink Command: 0x22**
713 713  
714 714  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
715 715  
716 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
717 -* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
699 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
700 +* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
718 718  
719 -
720 -
721 -
722 722  == 7.2 LoRa® Class ==
723 723  
724 724  
... ... @@ -737,8 +737,6 @@
737 737  
738 738  )))
739 739  
740 -
741 -
742 742  == 7.3 Duty Cycle Setting ==
743 743  
744 744  
... ... @@ -757,8 +757,6 @@
757 757  
758 758  )))
759 759  
760 -
761 -
762 762  == 7.4 Data Rate ==
763 763  
764 764  
... ... @@ -777,17 +777,13 @@
777 777  
778 778  )))
779 779  
780 -
781 781  (% style="color:blue" %)**Downlink Command: 0x2200aaFF**
782 782  
783 783  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
784 784  
785 -* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
786 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
760 +* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
761 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
787 787  
788 -
789 -
790 -
791 791  == 7.5 Frame Counter Downlink ==
792 792  
793 793  
... ... @@ -806,8 +806,6 @@
806 806  OK
807 807  )))
808 808  
809 -
810 -
811 811  == 7.6 Frame Counter Uplink ==
812 812  
813 813  Feature: Get or Set the Frame Counter Uplink.
... ... @@ -825,8 +825,6 @@
825 825  
826 826  )))
827 827  
828 -
829 -
830 830  == 7.7 Join Accept Delay1 ==
831 831  
832 832  
... ... @@ -845,8 +845,6 @@
845 845  
846 846  )))
847 847  
848 -
849 -
850 850  == 7.8 Join Accept Delay2 ==
851 851  
852 852  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
... ... @@ -869,7 +869,7 @@
869 869  
870 870  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
871 871  
872 -(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
838 +(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
873 873  
874 874  
875 875  (% style="color:blue" %)**AT Command:AT+PNM**
... ... @@ -909,7 +909,6 @@
909 909  
910 910  )))
911 911  
912 -
913 913  == 7.11 Receive Delay2 ==
914 914  
915 915  
... ... @@ -928,7 +928,6 @@
928 928  
929 929  )))
930 930  
931 -
932 932  == 7.12 Rx2 Window Data Rate ==
933 933  
934 934  
... ... @@ -947,7 +947,6 @@
947 947  
948 948  )))
949 949  
950 -
951 951  == 7.13 Rx2 Window Frequency ==
952 952  
953 953  
... ... @@ -966,13 +966,14 @@
966 966  
967 967  )))
968 968  
969 -
970 970  == 7.14 Transmit Power ==
971 971  
972 972  
973 973  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
974 974  
937 +Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor
975 975  
939 +
976 976  (% style="color:blue" %)**AT Command:AT+TXP**
977 977  
978 978  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
... ... @@ -989,11 +989,10 @@
989 989  
990 990  If the downlink payload=22000100, it means setting the TXP to 0.
991 991  
992 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
993 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
956 +* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
957 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
994 994  
995 995  
996 -
997 997  == 7.15 RSSI of the Last Received Packet ==
998 998  
999 999  
... ... @@ -1009,7 +1009,6 @@
1009 1009  OK
1010 1010  )))
1011 1011  
1012 -
1013 1013  == 7.16 SNR of the Last Received Packet ==
1014 1014  
1015 1015  
... ... @@ -1025,7 +1025,6 @@
1025 1025  OK
1026 1026  )))
1027 1027  
1028 -
1029 1029  == 7.17 Application Port ==
1030 1030  
1031 1031  
... ... @@ -1048,11 +1048,10 @@
1048 1048  
1049 1049  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1050 1050  
1051 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1052 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1012 +* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1013 +* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1053 1053  
1054 1054  
1055 -
1056 1056  == 7.18 Single Channel Mode ==
1057 1057  
1058 1058  
... ... @@ -1069,9 +1069,9 @@
1069 1069  )))
1070 1070  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1071 1071  
1072 -
1073 1073  == 7.19 Eight Channel Mode ==
1074 1074  
1034 +
1075 1075  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1076 1076  
1077 1077  
... ... @@ -1093,11 +1093,10 @@
1093 1093  
1094 1094  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1095 1095  
1096 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1097 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1056 +* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1057 +* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1098 1098  
1099 1099  
1100 -
1101 1101  == 7.20 Get or Set RXwindows1 timeout ==
1102 1102  
1103 1103  
... ... @@ -1147,7 +1147,6 @@
1147 1147  )))
1148 1148  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1149 1149  
1150 -
1151 1151  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1152 1152  
1153 1153  
... ... @@ -1170,11 +1170,10 @@
1170 1170  
1171 1171  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1172 1172  
1173 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1174 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1131 +* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1132 +* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1175 1175  
1176 1176  
1177 -
1178 1178  == 7.23 Set Packet Receiving Response Level ==
1179 1179  
1180 1180  
... ... @@ -1181,7 +1181,7 @@
1181 1181  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1182 1182  
1183 1183  
1184 -RPL value:
1141 +**RPL value:**
1185 1185  
1186 1186  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1187 1187  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1189,14 +1189,12 @@
1189 1189  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1190 1190  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1191 1191  
1149 +**Case Analyes:**
1192 1192  
1193 -Case Analyes:
1194 -
1195 1195  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1196 1196  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1197 1197  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1198 1198  
1199 -
1200 1200  (% style="color:blue" %)**AT Command: AT+RPL**
1201 1201  
1202 1202  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
... ... @@ -1213,23 +1213,26 @@
1213 1213  
1214 1214  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1215 1215  
1216 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1217 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1171 +* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1172 +* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1218 1218  
1219 1219  
1220 -
1221 1221  == 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1222 1222  
1223 1223  
1224 1224  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1225 1225  
1226 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1227 -|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1228 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1229 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1180 +(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1181 +|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1182 +|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1183 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1230 1230  OK
1231 1231  )))
1232 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1186 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1187 +value2: 0: uplink fcnt doesn't change for each NBTrans;
1188 +
1189 +1: uplink fcnt increase by 1 for each NBTrans.
1190 +)))|(% style="width:87px" %)(((
1233 1233  1
1234 1234  
1235 1235  OK
... ... @@ -1241,11 +1241,10 @@
1241 1241  
1242 1242  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1243 1243  
1244 -* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1245 -* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1202 +* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1203 +* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1246 1246  
1247 1247  
1248 -
1249 1249  == 7.25 Device offline rejoining （LWS007) ==
1250 1250  
1251 1251  
... ... @@ -1288,10 +1288,9 @@
1288 1288  
1289 1289  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1290 1290  
1291 -* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1248 +* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1292 1292  
1293 1293  
1294 -
1295 1295  == 7.26 Request the server to send an ACK ==
1296 1296  
1297 1297  
... ... @@ -1309,7 +1309,6 @@
1309 1309  OK
1310 1310  )))
1311 1311  
1312 -
1313 1313  == 7.27 Adjust network rejoining interval ==
1314 1314  
1315 1315  
... ... @@ -1333,11 +1333,10 @@
1333 1333  
1334 1334  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1335 1335  
1336 -* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1337 -* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1291 +* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1292 +* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1338 1338  
1339 1339  
1340 -
1341 1341  = 8. AT Commands Combination =
1342 1342  
1343 1343  
... ... @@ -1348,7 +1348,6 @@
1348 1348  * **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1349 1349  
1350 1350  
1351 -
1352 1352  == 8.2 Use Downlink Command to set a fix uplink DR ==
1353 1353  
1354 1354  
... ... @@ -1356,6 +1356,8 @@
1356 1356  
1357 1357  **Same as:**
1358 1358  
1359 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1360 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1361 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1312 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1313 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1314 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1315 +
1316 +

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0