Last modified by kai on 2024/09/06 10:00
<
From version < 51.17 >
edited by Xiaoling
on 2022/07/13 14:14
To version < 52.13 >
edited by Xiaoling
on 2022/09/19 15:27
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,12 +9,14 @@
9 9  
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
13 -* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
12 +* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 +* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 +
19 +
18 18  )))
19 19  
20 20  = 2. How to use AT Commands or Downlink command =
... ... @@ -28,7 +28,6 @@
28 28  
29 29  
30 30  
31 -
32 32  = 3. Support End Node and firmware version =
33 33  
34 34  
... ... @@ -105,7 +105,6 @@
105 105  
106 106  
107 107  
108 -
109 109  = 4. System Management Commands =
110 110  
111 111  
... ... @@ -138,15 +138,14 @@
138 138  )))
139 139  
140 140  (((
141 -If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
141 +If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
142 142  )))
143 143  
144 -* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 -* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
144 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 146  
147 147  
148 148  
149 -
150 150  == 4.2 Reboot End Node ==
151 151  
152 152  
... ... @@ -155,10 +155,10 @@
155 155  
156 156  (% style="color:blue" %)**AT Command: ATZ**
157 157  
158 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
159 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU
160 -|**Command Example**|**Function**|**Response**
161 -|ATZ|Reset MCU|(((
157 +(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
158 +|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
159 +|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
160 +|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
162 162  Device reset and show booting info
163 163  
164 164  LSN50 Device/LoRa ST Module
... ... @@ -181,6 +181,7 @@
181 181  (((
182 182  If the downlink payload=**04FF**, the end node will reboot.
183 183  
183 +
184 184  
185 185  )))
186 186  
... ... @@ -192,10 +192,10 @@
192 192  
193 193  (% style="color:blue" %)**AT Command: AT+FDR**
194 194  
195 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
196 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default
197 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
198 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
195 +(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
196 +|=(% colspan="3" style="width: 786px;" %)Reset to factory default
197 +|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
198 +|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
199 199  Device reset to factory default parameters and show booting info
200 200  
201 201  LSN50 Device/LoRa ST Module
... ... @@ -220,6 +220,7 @@
220 220  )))
221 221  
222 222  
223 +
223 223  == 4.4 Show Firmware Version ==
224 224  
225 225  
... ... @@ -228,10 +228,10 @@
228 228  
229 229  (% style="color:blue" %)**AT Command: AT+VER**
230 230  
231 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
232 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
233 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
234 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
232 +(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
233 +|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
234 +|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
235 +|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
235 235  1.3 EU868
236 236  
237 237  OK
... ... @@ -284,6 +284,7 @@
284 284  firmware version: v1.1.0 ~-~-> 110
285 285  
286 286  
288 +
287 287  == 4.5 Show System Configure ==
288 288  
289 289  
... ... @@ -475,12 +475,11 @@
475 475  
476 476  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
477 477  
478 -* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
479 -* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
480 +* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
481 +* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
480 480  
481 481  
482 482  
483 -
484 484  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
485 485  
486 486  
... ... @@ -523,12 +523,11 @@
523 523  
524 524  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
525 525  
526 -* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
527 -* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
527 +* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
528 +* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
528 528  
529 529  
530 530  
531 -
532 532  == 6.2 Confirm Status ==
533 533  
534 534  
... ... @@ -588,12 +588,11 @@
588 588  
589 589  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
590 590  
591 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
592 -* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
591 +* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
592 +* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
593 593  
594 594  
595 595  
596 -
597 597  == 6.5 LoRa® Network Join Status ==
598 598  
599 599  
... ... @@ -674,11 +674,11 @@
674 674  
675 675  (% style="color:blue" %)**AT Command: AT+SENDB**
676 676  
677 -(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
678 -|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
679 -|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
680 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
681 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
676 +(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
677 +|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
678 +|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
679 +|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
680 +|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
682 682  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
683 683  
684 684  
... ... @@ -708,17 +708,15 @@
708 708  AT_PARAM_ERROR
709 709  )))
710 710  
711 -
712 712  (% style="color:blue" %)**Downlink Command: 0x22**
713 713  
714 714  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
715 715  
716 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
717 -* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
714 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
715 +* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
718 718  
719 719  
720 720  
721 -
722 722  == 7.2 LoRa® Class ==
723 723  
724 724  
... ... @@ -725,7 +725,7 @@
725 725  Feature: Get or Set the Device Class(Currently only support class A, class C).
726 726  
727 727  
728 -(% style="color:blue" %)**AT Command:AT+CLASS**
725 +(% style="color:blue" %)**AT Command:  AT+CLASS**
729 729  
730 730  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
731 731  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
... ... @@ -742,10 +742,10 @@
742 742  == 7.3 Duty Cycle Setting ==
743 743  
744 744  
745 -Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
742 +Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
746 746  
747 747  
748 -(% style="color:blue" %)**AT Command:AT+DCS**
745 +(% style="color:blue" %)**AT Command:  AT+DCS**
749 749  
750 750  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
751 751  |=(% colspan="3" style="width: 512px;" %)AT+DCS
... ... @@ -777,17 +777,15 @@
777 777  
778 778  )))
779 779  
780 -
781 781  (% style="color:blue" %)**Downlink Command: 0x2200aaFF**
782 782  
783 783  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
784 784  
785 -* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
786 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
781 +* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
782 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
787 787  
788 788  
789 789  
790 -
791 791  == 7.5 Frame Counter Downlink ==
792 792  
793 793  
... ... @@ -794,7 +794,7 @@
794 794  Feature: Get or Set the Frame Counter Downlink.
795 795  
796 796  
797 -(% style="color:blue" %)**AT Command:AT+FCD**
792 +(% style="color:blue" %)**AT Command:  AT+FCD**
798 798  
799 799  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
800 800  |=(% colspan="3" style="width: 690px;" %)AT+FCD
... ... @@ -813,7 +813,7 @@
813 813  Feature: Get or Set the Frame Counter Uplink.
814 814  
815 815  
816 -(% style="color:blue" %)**AT Command:AT+FCU**
811 +(% style="color:blue" %)**AT Command:  AT+FCU**
817 817  
818 818  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
819 819  |=(% colspan="3" style="width: 531px;" %)AT+FCU
... ... @@ -833,7 +833,7 @@
833 833  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
834 834  
835 835  
836 -(% style="color:blue" %)**AT Command:AT+JN1DL**
831 +(% style="color:blue" %)**AT Command:  AT+JN1DL**
837 837  
838 838  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
839 839  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
... ... @@ -849,10 +849,11 @@
849 849  
850 850  == 7.8 Join Accept Delay2 ==
851 851  
847 +
852 852  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
853 853  
854 854  
855 -(% style="color:blue" %)**AT Command:AT+JN2DL**
851 +(% style="color:blue" %)**AT Command:  AT+JN2DL**
856 856  
857 857  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
858 858  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
... ... @@ -864,15 +864,17 @@
864 864  
865 865  )))
866 866  
863 +
864 +
867 867  == 7.9 Public Network Mode ==
868 868  
869 869  
870 870  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
871 871  
872 -(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
870 +(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
873 873  
874 874  
875 -(% style="color:blue" %)**AT Command:AT+PNM**
873 +(% style="color:blue" %)**AT Command:  AT+PNM**
876 876  
877 877  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
878 878  |=(% colspan="3" style="width: 664px;" %)AT+PNM
... ... @@ -891,6 +891,8 @@
891 891  )))
892 892  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
893 893  
892 +
893 +
894 894  == 7.10 Receive Delay1 ==
895 895  
896 896  
... ... @@ -897,7 +897,7 @@
897 897  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
898 898  
899 899  
900 -(% style="color:blue" %)**AT Command:AT+RX1DL**
900 +(% style="color:blue" %)**AT Command: AT+RX1DL**
901 901  
902 902  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
903 903  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
... ... @@ -910,6 +910,7 @@
910 910  )))
911 911  
912 912  
913 +
913 913  == 7.11 Receive Delay2 ==
914 914  
915 915  
... ... @@ -916,7 +916,7 @@
916 916  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
917 917  
918 918  
919 -(% style="color:blue" %)**AT Command:AT+RX2DL**
920 +(% style="color:blue" %)**AT Command: AT+RX2DL**
920 920  
921 921  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
922 922  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
... ... @@ -929,6 +929,7 @@
929 929  )))
930 930  
931 931  
933 +
932 932  == 7.12 Rx2 Window Data Rate ==
933 933  
934 934  
... ... @@ -935,7 +935,7 @@
935 935  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
936 936  
937 937  
938 -(% style="color:blue" %)**AT Command:AT+RX2DR**
940 +(% style="color:blue" %)**AT Command:  AT+RX2DR**
939 939  
940 940  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
941 941  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
... ... @@ -948,6 +948,7 @@
948 948  )))
949 949  
950 950  
953 +
951 951  == 7.13 Rx2 Window Frequency ==
952 952  
953 953  
... ... @@ -954,7 +954,7 @@
954 954  Feature: Get or Set the Rx2 window frequency
955 955  
956 956  
957 -(% style="color:blue" %)**AT Command:AT+RX2FQ**
960 +(% style="color:blue" %)**AT Command:  AT+RX2FQ**
958 958  
959 959  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
960 960  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
... ... @@ -967,14 +967,17 @@
967 967  )))
968 968  
969 969  
973 +
970 970  == 7.14 Transmit Power ==
971 971  
972 972  
973 973  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
974 974  
979 +(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
975 975  
976 -(% style="color:blue" %)**AT Command:AT+TXP**
977 977  
982 +(% style="color:blue" %)**AT Command:  AT+TXP**
983 +
978 978  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
979 979  |=(% colspan="3" style="width: 462px;" %)AT+TXP
980 980  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -989,8 +989,8 @@
989 989  
990 990  If the downlink payload=22000100, it means setting the TXP to 0.
991 991  
992 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
993 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
998 +* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
999 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
994 994  
995 995  
996 996  
... ... @@ -1010,6 +1010,7 @@
1010 1010  )))
1011 1011  
1012 1012  
1019 +
1013 1013  == 7.16 SNR of the Last Received Packet ==
1014 1014  
1015 1015  
... ... @@ -1016,7 +1016,7 @@
1016 1016  Feature: Get the SNR of the last received packet
1017 1017  
1018 1018  
1019 -(% style="color:blue" %)**AT Command:AT+SNR**
1026 +(% style="color:blue" %)**AT Command:  AT+SNR**
1020 1020  
1021 1021  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
1022 1022  |=(% colspan="3" style="width: 568px;" %)AT+SNR
... ... @@ -1026,6 +1026,7 @@
1026 1026  )))
1027 1027  
1028 1028  
1036 +
1029 1029  == 7.17 Application Port ==
1030 1030  
1031 1031  
... ... @@ -1048,8 +1048,8 @@
1048 1048  
1049 1049  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1050 1050  
1051 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1052 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1059 +* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1060 +* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1053 1053  
1054 1054  
1055 1055  
... ... @@ -1070,8 +1070,10 @@
1070 1070  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1071 1071  
1072 1072  
1081 +
1073 1073  == 7.19 Eight Channel Mode ==
1074 1074  
1084 +
1075 1075  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1076 1076  
1077 1077  
... ... @@ -1093,8 +1093,8 @@
1093 1093  
1094 1094  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1095 1095  
1096 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1097 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1106 +* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1107 +* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1098 1098  
1099 1099  
1100 1100  
... ... @@ -1117,8 +1117,9 @@
1117 1117  (((
1118 1118  
1119 1119  
1120 -**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1121 1121  
1131 +(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1132 +
1122 1122  
1123 1123  )))
1124 1124  
... ... @@ -1128,6 +1128,7 @@
1128 1128  (((
1129 1129  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1130 1130  
1142 +
1131 1131  
1132 1132  )))
1133 1133  
... ... @@ -1148,6 +1148,7 @@
1148 1148  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1149 1149  
1150 1150  
1163 +
1151 1151  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1152 1152  
1153 1153  
... ... @@ -1170,8 +1170,8 @@
1170 1170  
1171 1171  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1172 1172  
1173 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1174 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1186 +* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1187 +* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1175 1175  
1176 1176  
1177 1177  
... ... @@ -1181,7 +1181,7 @@
1181 1181  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1182 1182  
1183 1183  
1184 -RPL value:
1197 +**RPL value:**
1185 1185  
1186 1186  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1187 1187  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1189,9 +1189,8 @@
1189 1189  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1190 1190  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1191 1191  
1205 +**Case Analyes:**
1192 1192  
1193 -Case Analyes:
1194 -
1195 1195  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1196 1196  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1197 1197  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
... ... @@ -1213,8 +1213,8 @@
1213 1213  
1214 1214  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1215 1215  
1216 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1217 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1228 +* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1229 +* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1218 1218  
1219 1219  
1220 1220  
... ... @@ -1223,13 +1223,17 @@
1223 1223  
1224 1224  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1225 1225  
1226 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1227 -|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1228 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1229 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1238 +(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1239 +|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1240 +|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1241 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1230 1230  OK
1231 1231  )))
1232 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1244 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1245 +value2: 0: uplink fcnt doesn't change for each NBTrans;
1246 +
1247 +1: uplink fcnt increase by 1 for each NBTrans.
1248 +)))|(% style="width:87px" %)(((
1233 1233  1
1234 1234  
1235 1235  OK
... ... @@ -1241,8 +1241,8 @@
1241 1241  
1242 1242  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1243 1243  
1244 -* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1245 -* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1260 +* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1261 +* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1246 1246  
1247 1247  
1248 1248  
... ... @@ -1288,7 +1288,7 @@
1288 1288  
1289 1289  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1290 1290  
1291 -* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1307 +* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1292 1292  
1293 1293  
1294 1294  
... ... @@ -1310,6 +1310,8 @@
1310 1310  )))
1311 1311  
1312 1312  
1329 +
1330 +
1313 1313  == 7.27 Adjust network rejoining interval ==
1314 1314  
1315 1315  
... ... @@ -1333,8 +1333,8 @@
1333 1333  
1334 1334  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1335 1335  
1336 -* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1337 -* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1354 +* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1355 +* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1338 1338  
1339 1339  
1340 1340  
... ... @@ -1344,8 +1344,8 @@
1344 1344  == 8.1 Set a fix RX2DR for downlink window ==
1345 1345  
1346 1346  
1347 -* **AT+ADR=0             ** **~-~->**  Disable ADR first
1348 -* **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1365 +* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1366 +* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1349 1349  
1350 1350  
1351 1351  
... ... @@ -1356,6 +1356,8 @@
1356 1356  
1357 1357  **Same as:**
1358 1358  
1359 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1360 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1361 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1377 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1378 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1379 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1380 +
1381 +

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0