Last modified by kai on 2024/09/06 10:00
<
From version < 51.16 >
edited by Xiaoling
on 2022/07/13 14:14
To version < 52.13 >
edited by Xiaoling
on 2022/09/19 15:27
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,12 +9,14 @@
9 9  
10 10  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
11 11  
12 -* **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
13 -* **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
12 +* (% style="color:blue" %)**Common Commands:** (%%) They should be available for each sensor, such as: change uplink interval, reset device.
13 +* (% style="color:blue" %)**Sensor Related Commands:** (%%) Only for special sensor, such as control relay, poll RS485 device.
14 14  
15 15  (((
16 16  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
17 17  
18 +
19 +
18 18  )))
19 19  
20 20  = 2. How to use AT Commands or Downlink command =
... ... @@ -28,7 +28,6 @@
28 28  
29 29  
30 30  
31 -
32 32  = 3. Support End Node and firmware version =
33 33  
34 34  
... ... @@ -105,7 +105,6 @@
105 105  
106 106  
107 107  
108 -
109 109  = 4. System Management Commands =
110 110  
111 111  
... ... @@ -138,15 +138,14 @@
138 138  )))
139 139  
140 140  (((
141 -If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
141 +If the downlink payload=0100003C, it means set the END Node's Transmit Interval to 0x00003C=60(S), while type code is 01.
142 142  )))
143 143  
144 -* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 -* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
144 +* **Example 1**: Downlink Payload:** 0100001E**  ~/~/ Set Transmit Interval (TDC) = 30 seconds
145 +* **Example 2**: Downlink Payload:** 0100003C**  ~/~/ Set Transmit Interval (TDC) = 60 seconds
146 146  
147 147  
148 148  
149 -
150 150  == 4.2 Reboot End Node ==
151 151  
152 152  
... ... @@ -155,10 +155,10 @@
155 155  
156 156  (% style="color:blue" %)**AT Command: ATZ**
157 157  
158 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
159 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU
160 -|**Command Example**|**Function**|**Response**
161 -|ATZ|Reset MCU|(((
157 +(% border="1" style="background-color:#ffffcc; color:green; width:546px" %)
158 +|=(% colspan="3" style="width: 543px;" %)ATZ: Trig a reset of the MCU
159 +|(% style="width:157px" %)**Command Example**|(% style="width:92px" %)**Function**|(% style="width:294px" %)**Response**
160 +|(% style="width:157px" %)ATZ|(% style="width:92px" %)Reset MCU|(% style="width:294px" %)(((
162 162  Device reset and show booting info
163 163  
164 164  LSN50 Device/LoRa ST Module
... ... @@ -181,6 +181,7 @@
181 181  (((
182 182  If the downlink payload=**04FF**, the end node will reboot.
183 183  
183 +
184 184  
185 185  )))
186 186  
... ... @@ -192,10 +192,10 @@
192 192  
193 193  (% style="color:blue" %)**AT Command: AT+FDR**
194 194  
195 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
196 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default
197 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
198 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
195 +(% border="1" style="background-color:#ffffcc; color:green; width:789px" %)
196 +|=(% colspan="3" style="width: 786px;" %)Reset to factory default
197 +|(% style="width:154px" %)**Command Example**|(% style="width:175px" %)**Function**|(% style="width:456px" %)**Response**
198 +|(% style="width:154px" %)AT+FDR|(% style="width:175px" %)Reset to factory default|(% style="width:456px" %)(((
199 199  Device reset to factory default parameters and show booting info
200 200  
201 201  LSN50 Device/LoRa ST Module
... ... @@ -220,6 +220,7 @@
220 220  )))
221 221  
222 222  
223 +
223 223  == 4.4 Show Firmware Version ==
224 224  
225 225  
... ... @@ -228,10 +228,10 @@
228 228  
229 229  (% style="color:blue" %)**AT Command: AT+VER**
230 230  
231 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
232 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
233 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
234 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
232 +(% border="1" style="background-color:#ffffcc; color:green; width:542px" %)
233 +|=(% colspan="3" style="width: 539px;" %)AT+VER: Image Version and Frequency Band
234 +|(% style="width:157px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:86px" %)**Response**
235 +|(% style="width:157px" %)AT+VER=?|(% style="width:295px" %)Show Image version and Frequency Band|(% style="width:86px" %)(((
235 235  1.3 EU868
236 236  
237 237  OK
... ... @@ -284,6 +284,7 @@
284 284  firmware version: v1.1.0 ~-~-> 110
285 285  
286 286  
288 +
287 287  == 4.5 Show System Configure ==
288 288  
289 289  
... ... @@ -475,12 +475,11 @@
475 475  
476 476  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
477 477  
478 -* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
479 -* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
480 +* **Example 1:** Downlink Payload: 0501  ~/~/ Set AT+CFM=1
481 +* **Example 2:** Downlink Payload: 0500  ~/~/ Set AT+CFM=0
480 480  
481 481  
482 482  
483 -
484 484  === 6.1.2  AT+CFM command since DR-LWS007 software stack ===
485 485  
486 486  
... ... @@ -523,12 +523,11 @@
523 523  
524 524  If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
525 525  
526 -* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
527 -* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
527 +* **Example 1:** Downlink Payload: 05010101  ~/~/ Set AT+CFM=1,1,1
528 +* **Example 2:** Downlink Payload: 05000700  ~/~/ Set AT+CFM=0,7,0
528 528  
529 529  
530 530  
531 -
532 532  == 6.2 Confirm Status ==
533 533  
534 534  
... ... @@ -588,12 +588,11 @@
588 588  
589 589  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
590 590  
591 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
592 -* **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
591 +* **Example 1: **Downlink Payload: **2000                  ** ~/~/ Set AT+NJM=0
592 +* **Example 2:** Downlink Payload: **2001**  ~/~/ Set AT+NJM=1
593 593  
594 594  
595 595  
596 -
597 597  == 6.5 LoRa® Network Join Status ==
598 598  
599 599  
... ... @@ -674,11 +674,11 @@
674 674  
675 675  (% style="color:blue" %)**AT Command: AT+SENDB**
676 676  
677 -(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
678 -|=(% colspan="3" style="width: 1117px;" %)AT+SENDB
679 -|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
680 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
681 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return(((
676 +(% border="1" style="background-color:#ffffcc; color:green; width:1101px" %)
677 +|=(% colspan="3" style="width: 1098px;" %)AT+SENDB
678 +|(% style="width:257px" %)**Command Example**|(% style="width:394px" %)**Function**|(% style="width:446px" %)**Response**
679 +|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)OK
680 +|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:394px" %)Send hexadecimal data along with the application port.|(% style="width:446px" %)While Error in format, return(((
682 682  AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED
683 683  
684 684  
... ... @@ -708,17 +708,15 @@
708 708  AT_PARAM_ERROR
709 709  )))
710 710  
711 -
712 712  (% style="color:blue" %)**Downlink Command: 0x22**
713 713  
714 714  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
715 715  
716 -* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
717 -* **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
714 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
715 +* **Example 2**: Downlink Payload: **2200FFFF**  ~/~/ Set AT+ADR=0.
718 718  
719 719  
720 720  
721 -
722 722  == 7.2 LoRa® Class ==
723 723  
724 724  
... ... @@ -725,7 +725,7 @@
725 725  Feature: Get or Set the Device Class(Currently only support class A, class C).
726 726  
727 727  
728 -(% style="color:blue" %)**AT Command:AT+CLASS**
725 +(% style="color:blue" %)**AT Command:  AT+CLASS**
729 729  
730 730  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
731 731  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
... ... @@ -742,10 +742,10 @@
742 742  == 7.3 Duty Cycle Setting ==
743 743  
744 744  
745 -Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
742 +Feature: Get or Set the ETSI Duty Cycle setting** - 0**=disable, **1**=enable - Only for testing.
746 746  
747 747  
748 -(% style="color:blue" %)**AT Command:AT+DCS**
745 +(% style="color:blue" %)**AT Command:  AT+DCS**
749 749  
750 750  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
751 751  |=(% colspan="3" style="width: 512px;" %)AT+DCS
... ... @@ -777,17 +777,15 @@
777 777  
778 778  )))
779 779  
780 -
781 781  (% style="color:blue" %)**Downlink Command: 0x2200aaFF**
782 782  
783 783  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
784 784  
785 -* **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
786 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
781 +* **Example 1**: Downlink Payload: **220001FF**  ~/~/ Set AT+DR=1.
782 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+DR=0.
787 787  
788 788  
789 789  
790 -
791 791  == 7.5 Frame Counter Downlink ==
792 792  
793 793  
... ... @@ -794,7 +794,7 @@
794 794  Feature: Get or Set the Frame Counter Downlink.
795 795  
796 796  
797 -(% style="color:blue" %)**AT Command:AT+FCD**
792 +(% style="color:blue" %)**AT Command:  AT+FCD**
798 798  
799 799  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
800 800  |=(% colspan="3" style="width: 690px;" %)AT+FCD
... ... @@ -813,7 +813,7 @@
813 813  Feature: Get or Set the Frame Counter Uplink.
814 814  
815 815  
816 -(% style="color:blue" %)**AT Command:AT+FCU**
811 +(% style="color:blue" %)**AT Command:  AT+FCU**
817 817  
818 818  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
819 819  |=(% colspan="3" style="width: 531px;" %)AT+FCU
... ... @@ -825,6 +825,8 @@
825 825  
826 826  )))
827 827  
823 +
824 +
828 828  == 7.7 Join Accept Delay1 ==
829 829  
830 830  
... ... @@ -831,7 +831,7 @@
831 831  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
832 832  
833 833  
834 -(% style="color:blue" %)**AT Command:AT+JN1DL**
831 +(% style="color:blue" %)**AT Command:  AT+JN1DL**
835 835  
836 836  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
837 837  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
... ... @@ -843,12 +843,15 @@
843 843  
844 844  )))
845 845  
843 +
844 +
846 846  == 7.8 Join Accept Delay2 ==
847 847  
847 +
848 848  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
849 849  
850 850  
851 -(% style="color:blue" %)**AT Command:AT+JN2DL**
851 +(% style="color:blue" %)**AT Command:  AT+JN2DL**
852 852  
853 853  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
854 854  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
... ... @@ -860,15 +860,17 @@
860 860  
861 861  )))
862 862  
863 +
864 +
863 863  == 7.9 Public Network Mode ==
864 864  
865 865  
866 866  Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
867 867  
868 -(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
870 +(% style="color:red" %)**Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network.**
869 869  
870 870  
871 -(% style="color:blue" %)**AT Command:AT+PNM**
873 +(% style="color:blue" %)**AT Command:  AT+PNM**
872 872  
873 873  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
874 874  |=(% colspan="3" style="width: 664px;" %)AT+PNM
... ... @@ -887,6 +887,8 @@
887 887  )))
888 888  |(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
889 889  
892 +
893 +
890 890  == 7.10 Receive Delay1 ==
891 891  
892 892  
... ... @@ -893,7 +893,7 @@
893 893  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
894 894  
895 895  
896 -(% style="color:blue" %)**AT Command:AT+RX1DL**
900 +(% style="color:blue" %)**AT Command: AT+RX1DL**
897 897  
898 898  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
899 899  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
... ... @@ -906,6 +906,7 @@
906 906  )))
907 907  
908 908  
913 +
909 909  == 7.11 Receive Delay2 ==
910 910  
911 911  
... ... @@ -912,7 +912,7 @@
912 912  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
913 913  
914 914  
915 -(% style="color:blue" %)**AT Command:AT+RX2DL**
920 +(% style="color:blue" %)**AT Command: AT+RX2DL**
916 916  
917 917  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
918 918  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
... ... @@ -925,6 +925,7 @@
925 925  )))
926 926  
927 927  
933 +
928 928  == 7.12 Rx2 Window Data Rate ==
929 929  
930 930  
... ... @@ -931,7 +931,7 @@
931 931  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
932 932  
933 933  
934 -(% style="color:blue" %)**AT Command:AT+RX2DR**
940 +(% style="color:blue" %)**AT Command:  AT+RX2DR**
935 935  
936 936  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
937 937  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
... ... @@ -944,6 +944,7 @@
944 944  )))
945 945  
946 946  
953 +
947 947  == 7.13 Rx2 Window Frequency ==
948 948  
949 949  
... ... @@ -950,7 +950,7 @@
950 950  Feature: Get or Set the Rx2 window frequency
951 951  
952 952  
953 -(% style="color:blue" %)**AT Command:AT+RX2FQ**
960 +(% style="color:blue" %)**AT Command:  AT+RX2FQ**
954 954  
955 955  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
956 956  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
... ... @@ -963,14 +963,17 @@
963 963  )))
964 964  
965 965  
973 +
966 966  == 7.14 Transmit Power ==
967 967  
968 968  
969 969  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
970 970  
979 +(% style="color:red" %)**Notice: Transmit Power might be changed by ADR from LoRaWAN server. So manually change TXP also remember to set AT+ADR=0 in sensor**
971 971  
972 -(% style="color:blue" %)**AT Command:AT+TXP**
973 973  
982 +(% style="color:blue" %)**AT Command:  AT+TXP**
983 +
974 974  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
975 975  |=(% colspan="3" style="width: 462px;" %)AT+TXP
976 976  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -985,8 +985,8 @@
985 985  
986 986  If the downlink payload=22000100, it means setting the TXP to 0.
987 987  
988 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
989 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
998 +* **Example 1**: Downlink Payload: **22000102**  ~/~/ Set AT+TXP=2.
999 +* **Example 2**: Downlink Payload: **220000FF**  ~/~/ Set AT+TXP=0.
990 990  
991 991  
992 992  
... ... @@ -1006,6 +1006,7 @@
1006 1006  )))
1007 1007  
1008 1008  
1019 +
1009 1009  == 7.16 SNR of the Last Received Packet ==
1010 1010  
1011 1011  
... ... @@ -1012,7 +1012,7 @@
1012 1012  Feature: Get the SNR of the last received packet
1013 1013  
1014 1014  
1015 -(% style="color:blue" %)**AT Command:AT+SNR**
1026 +(% style="color:blue" %)**AT Command:  AT+SNR**
1016 1016  
1017 1017  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
1018 1018  |=(% colspan="3" style="width: 568px;" %)AT+SNR
... ... @@ -1022,6 +1022,7 @@
1022 1022  )))
1023 1023  
1024 1024  
1036 +
1025 1025  == 7.17 Application Port ==
1026 1026  
1027 1027  
... ... @@ -1044,8 +1044,8 @@
1044 1044  
1045 1045  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
1046 1046  
1047 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
1048 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
1059 +* **Example 1**: Downlink Payload: **2301**  ~/~/ set the application port to 1
1060 +* **Example 2**: Downlink Payload:** 2305**  ~/~/ set the application port to 5
1049 1049  
1050 1050  
1051 1051  
... ... @@ -1066,8 +1066,10 @@
1066 1066  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
1067 1067  
1068 1068  
1081 +
1069 1069  == 7.19 Eight Channel Mode ==
1070 1070  
1084 +
1071 1071  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
1072 1072  
1073 1073  
... ... @@ -1089,8 +1089,8 @@
1089 1089  
1090 1090  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
1091 1091  
1092 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
1093 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1106 +* **Example 1**: Downlink Payload: 2401  ~/~/ set channel mode to 1
1107 +* **Example 2**: Downlink Payload: 2405  ~/~/ set channel mode to 5
1094 1094  
1095 1095  
1096 1096  
... ... @@ -1113,8 +1113,9 @@
1113 1113  (((
1114 1114  
1115 1115  
1116 -**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1117 1117  
1131 +(% style="color:blue" %)**AT+RX1WTO**(%%) is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1132 +
1118 1118  
1119 1119  )))
1120 1120  
... ... @@ -1124,6 +1124,7 @@
1124 1124  (((
1125 1125  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1126 1126  
1142 +
1127 1127  
1128 1128  )))
1129 1129  
... ... @@ -1144,6 +1144,7 @@
1144 1144  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1145 1145  
1146 1146  
1163 +
1147 1147  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1148 1148  
1149 1149  
... ... @@ -1166,8 +1166,8 @@
1166 1166  
1167 1167  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1168 1168  
1169 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1170 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1186 +* **Example 1**: Downlink Payload: **2501**  ~/~/ set uplinkdwelltime to 1
1187 +* **Example 2**: Downlink Payload: **2500**  ~/~/ set uplinkdwelltime to 0
1171 1171  
1172 1172  
1173 1173  
... ... @@ -1177,7 +1177,7 @@
1177 1177  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1178 1178  
1179 1179  
1180 -RPL value:
1197 +**RPL value:**
1181 1181  
1182 1182  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1183 1183  * **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
... ... @@ -1185,9 +1185,8 @@
1185 1185  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1186 1186  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1187 1187  
1205 +**Case Analyes:**
1188 1188  
1189 -Case Analyes:
1190 -
1191 1191  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
1192 1192  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1193 1193  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
... ... @@ -1209,8 +1209,8 @@
1209 1209  
1210 1210  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1211 1211  
1212 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1213 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1228 +* **Example 1**: Downlink Payload: **2101**  ~/~/ set packet receiving response level to 1
1229 +* **Example 2**: Downlink Payload: **2102**  ~/~/ set packet receiving response level to 2
1214 1214  
1215 1215  
1216 1216  
... ... @@ -1219,13 +1219,17 @@
1219 1219  
1220 1220  (% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1221 1221  
1222 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1223 -|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1224 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1225 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1238 +(% border="1" style="background-color:#ffffcc; color:green; width:589px" %)
1239 +|=(% colspan="3" style="width: 586px;" %)AT+**SETMAXNBTRANS**
1240 +|(% style="width:227px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:87px" %)**Response**
1241 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:300px" %)Value1: set the maximum NBTrans.|(% style="width:87px" %)1(((
1226 1226  OK
1227 1227  )))
1228 -|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1244 +|(% style="width:227px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:300px" %)(((
1245 +value2: 0: uplink fcnt doesn't change for each NBTrans;
1246 +
1247 +1: uplink fcnt increase by 1 for each NBTrans.
1248 +)))|(% style="width:87px" %)(((
1229 1229  1
1230 1230  
1231 1231  OK
... ... @@ -1237,8 +1237,8 @@
1237 1237  
1238 1238  If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1239 1239  
1240 -* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1241 -* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1260 +* Example 1: Downlink Payload: 330100  ~/~/ Set AT+SETMAXNBTRANS=1,0
1261 +* Example 2: Downlink Payload: 330201  ~/~/ Set AT+SETMAXNBTRANS=2,1
1242 1242  
1243 1243  
1244 1244  
... ... @@ -1284,7 +1284,7 @@
1284 1284  
1285 1285  If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1286 1286  
1287 -* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1307 +* **Example 1:** Downlink Payload: 320105A00B40  ~/~/ Set AT+DDETECT=1,1440,2880
1288 1288  
1289 1289  
1290 1290  
... ... @@ -1306,6 +1306,8 @@
1306 1306  )))
1307 1307  
1308 1308  
1329 +
1330 +
1309 1309  == 7.27 Adjust network rejoining interval ==
1310 1310  
1311 1311  
... ... @@ -1329,8 +1329,8 @@
1329 1329  
1330 1330  If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1331 1331  
1332 -* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1333 -* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1354 +* **Example 1:** Downlink Payload: 26000A  ~/~/ Set AT+RJTDC=10
1355 +* **Example 2: **Downlink Payload: 260002  ~/~/ Set AT+RJTDC=2
1334 1334  
1335 1335  
1336 1336  
... ... @@ -1340,8 +1340,8 @@
1340 1340  == 8.1 Set a fix RX2DR for downlink window ==
1341 1341  
1342 1342  
1343 -* **AT+ADR=0             ** **~-~->**  Disable ADR first
1344 -* **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1365 +* (% style="color:blue" %)**AT+ADR=0             **(%%) **~-~->**  Disable ADR first
1366 +* (% style="color:blue" %)**AT+RX2DR=xxxx**   (%%) **~-~->**  Set xxxx to your wanted DataRate
1345 1345  
1346 1346  
1347 1347  
... ... @@ -1352,6 +1352,8 @@
1352 1352  
1353 1353  **Same as:**
1354 1354  
1355 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1356 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1357 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1377 +* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1378 +* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1379 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1380 +
1381 +

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0