Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -97,7 +97,6 @@
97	97	)))
98	98	)))
99	99
100		-
101	101	= 4. System Management Commands =
102	102
103	103	== 4.1 Change Uplink Interval ==
...	...	@@ -136,7 +136,6 @@
136	136	* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
137	137	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
138	138
139		-
140	140	== 4.2 Reboot End Node ==
141	141
142	142	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -172,8 +172,6 @@
172	172
173	173	(((
174	174	If the downlink payload=**04FF**, the end node will reboot.
175		-
176		-
177	177	)))
178	178
179	179	== 4.3 Reset to factory Default ==
...	...	@@ -298,8 +298,6 @@
298	298	OK
299	299	)))
300	300
301		-
302		-
303	303	= 5. Keys, IDs and EUIs management =
304	304
305	305	== 5.1 Application EUI ==
...	...	@@ -318,7 +318,6 @@
318	318	)))
319	319	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
320	320
321		-
322	322	== 5.2 Application Key ==
323	323
324	324	Feature: Get or Set the Application Key.
...	...	@@ -335,7 +335,6 @@
335	335	)))
336	336	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
337	337
338		-
339	339	== 5.3 Application Session Key ==
340	340
341	341	Feature: Get or Set the Application Session Key.
...	...	@@ -799,7 +799,7 @@
799	799
800	800	)))
801	801
802		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
803	803
804	804	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
805	805
...	...	@@ -1004,8 +1004,6 @@
1004	1004
1005	1005	(((
1006	1006	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1007		-
1008		-
1009	1009	)))
1010	1010
1011	1011	== 7.21 Get or Set RXwindows2 timeout ==