Last modified by kai on 2024/09/06 10:00
<
From version < 38.84 >
edited by Xiaoling
on 2022/05/31 09:20
To version < 21.1 >
edited by Xiaoling
on 2022/05/27 17:53
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -3,7 +3,6 @@
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
... ... @@ -20,8 +20,8 @@
20 20  
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
22 +** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
23 +** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25 25  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26 26  
27 27  
... ... @@ -139,7 +139,6 @@
139 139  * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140 140  
141 141  
142 -
143 143  == 4.2 Reboot End Node ==
144 144  
145 145  Feature: Reboot End Node to perform a new OTAA or ABP Join.
... ... @@ -302,7 +302,6 @@
302 302  )))
303 303  
304 304  
305 -
306 306  = 5. Keys, IDs and EUIs management =
307 307  
308 308  == 5.1 Application EUI ==
... ... @@ -322,7 +322,6 @@
322 322  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
323 323  
324 324  
325 -
326 326  == 5.2 Application Key ==
327 327  
328 328  Feature: Get or Set the Application Key.
... ... @@ -359,6 +359,7 @@
359 359  )))
360 360  
361 361  
358 +
362 362  == 5.4 Device Address ==
363 363  
364 364  Feature: Get or Set the Device Address.
... ... @@ -378,6 +378,7 @@
378 378  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
379 379  
380 380  
378 +
381 381  == 5.5 Device EUI ==
382 382  
383 383  Feature: Get or Set the Device EUI.
... ... @@ -397,6 +397,7 @@
397 397  )))
398 398  
399 399  
398 +
400 400  == 5.6 Network ID ==
401 401  
402 402  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
... ... @@ -414,6 +414,7 @@
414 414  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
415 415  
416 416  
416 +
417 417  == 5.7 Network Session Key ==
418 418  
419 419  Feature: Get or Set the Network Session Key
... ... @@ -431,6 +431,7 @@
431 431  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
432 432  
433 433  
434 +
434 434  = 6. Joining and sending date on LoRaWAN network =
435 435  
436 436  == 6.1 Confirm Mode ==
... ... @@ -460,6 +460,7 @@
460 460  * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
461 461  
462 462  
464 +
463 463  == 6.2 Confirm Status ==
464 464  
465 465  Feature: Get confirmation status of the last AT+SEND (0-1).
... ... @@ -476,6 +476,7 @@
476 476  )))
477 477  
478 478  
481 +
479 479  == 6.3 Join LoRa® Network ==
480 480  
481 481  Feature: Join network.
... ... @@ -523,6 +523,8 @@
523 523  * **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
524 524  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
525 525  
529 +
530 +
526 526  == 6.5 LoRa® Network Join Status ==
527 527  
528 528  Feature: LoRa® Network Join Status.
... ... @@ -538,6 +538,8 @@
538 538  OK
539 539  )))
540 540  
546 +
547 +
541 541  == 6.6 Print Last Received Data in Raw Format ==
542 542  
543 543  Feature: Print Last Received Data in Raw Format<port:data>.
... ... @@ -553,6 +553,8 @@
553 553  OK
554 554  )))
555 555  
563 +
564 +
556 556  == 6.7 Print Last Received Data in Binary Format ==
557 557  
558 558  Feature: Print Last Received Data in Binary Format<port:data>.
... ... @@ -568,6 +568,8 @@
568 568  OK
569 569  )))
570 570  
580 +
581 +
571 571  == 6.8 Send Text Data ==
572 572  
573 573  Feature: Send Text Data<port:data>.
... ... @@ -587,6 +587,8 @@
587 587  
588 588  )))
589 589  
601 +
602 +
590 590  == 6.9 Send Hexadecimal Data ==
591 591  
592 592  Feature: Send hexadecimal data along with the application port.
... ... @@ -605,6 +605,8 @@
605 605  
606 606  )))
607 607  
621 +
622 +
608 608  = 7. LoRaWAN network management =
609 609  
610 610  == 7.1 Adaptive Data Rate ==
... ... @@ -636,6 +636,8 @@
636 636  * **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
637 637  * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
638 638  
654 +
655 +
639 639  == 7.2 LoRa® Class ==
640 640  
641 641  Feature: Get or Set the Device Class(Currently only support class A, class C).
... ... @@ -654,6 +654,8 @@
654 654  
655 655  )))
656 656  
674 +
675 +
657 657  == 7.3 Duty Cycle Setting ==
658 658  
659 659  Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
... ... @@ -672,6 +672,8 @@
672 672  
673 673  )))
674 674  
694 +
695 +
675 675  == 7.4 Data Rate ==
676 676  
677 677  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
... ... @@ -700,6 +700,8 @@
700 700  * **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
701 701  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
702 702  
724 +
725 +
703 703  == 7.5 Frame Counter Downlink ==
704 704  
705 705  Feature: Get or Set the Frame Counter Downlink.
... ... @@ -720,6 +720,8 @@
720 720  
721 721  )))
722 722  
746 +
747 +
723 723  == 7.6 Frame Counter Uplink ==
724 724  
725 725  Feature: Get or Set the Frame Counter Uplink.
... ... @@ -738,6 +738,8 @@
738 738  
739 739  )))
740 740  
766 +
767 +
741 741  == 7.7 Join Accept Delay1 ==
742 742  
743 743  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
... ... @@ -756,6 +756,8 @@
756 756  
757 757  )))
758 758  
786 +
787 +
759 759  == 7.8 Join Accept Delay2 ==
760 760  
761 761  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
... ... @@ -774,6 +774,8 @@
774 774  
775 775  )))
776 776  
806 +
807 +
777 777  == 7.9 Public Network Mode ==
778 778  
779 779  Feature: Get or Set the public network mode. (0: off, 1: on)
... ... @@ -794,6 +794,8 @@
794 794  
795 795  )))
796 796  
828 +
829 +
797 797  == 7.10 Receive Delay1 ==
798 798  
799 799  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
... ... @@ -812,6 +812,8 @@
812 812  
813 813  )))
814 814  
848 +
849 +
815 815  == 7.11 Receive Delay2 ==
816 816  
817 817  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
... ... @@ -830,6 +830,8 @@
830 830  
831 831  )))
832 832  
868 +
869 +
833 833  == 7.12 Rx2 Window Data Rate ==
834 834  
835 835  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
... ... @@ -848,6 +848,8 @@
848 848  
849 849  )))
850 850  
888 +
889 +
851 851  == 7.13 Rx2 Window Frequency ==
852 852  
853 853  Feature: Get or Set the Rx2 window frequency
... ... @@ -866,6 +866,8 @@
866 866  
867 867  )))
868 868  
908 +
909 +
869 869  == 7.14 Transmit Power ==
870 870  
871 871  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
... ... @@ -891,6 +891,8 @@
891 891  * **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
892 892  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
893 893  
935 +
936 +
894 894  == 7.15 RSSI of the Last Received Packet ==
895 895  
896 896  Feature: Get or Set the Rx2 window frequency
... ... @@ -906,6 +906,8 @@
906 906  OK
907 907  )))
908 908  
952 +
953 +
909 909  == 7.16 SNR of the Last Received Packet ==
910 910  
911 911  Feature: Get the SNR of the last received packet
... ... @@ -921,6 +921,8 @@
921 921  OK
922 922  )))
923 923  
969 +
970 +
924 924  == 7.17 Application Port ==
925 925  
926 926  Feature: Get or set the application port.
... ... @@ -948,6 +948,8 @@
948 948  * **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
949 949  * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
950 950  
998 +
999 +
951 951  == 7.18 Single Channel Mode ==
952 952  
953 953  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
... ... @@ -964,6 +964,8 @@
964 964  )))
965 965  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
966 966  
1016 +
1017 +
967 967  == 7.19 Eight Channel Mode ==
968 968  
969 969  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
... ... @@ -993,6 +993,8 @@
993 993  * **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
994 994  * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
995 995  
1047 +
1048 +
996 996  == 7.20 Get or Set RXwindows1 timeout ==
997 997  
998 998  Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
... ... @@ -1037,6 +1037,8 @@
1037 1037  )))
1038 1038  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1039 1039  
1093 +
1094 +
1040 1040  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1041 1041  
1042 1042  Feature: Get or Set uplinkdwelltime
... ... @@ -1064,6 +1064,8 @@
1064 1064  * **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1065 1065  * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1066 1066  
1122 +
1123 +
1067 1067  == 7.23 Set Packet Receiving Response Level ==
1068 1068  
1069 1069  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
... ... @@ -1105,6 +1105,8 @@
1105 1105  * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1106 1106  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1107 1107  
1165 +
1166 +
1108 1108  = 8. AT Commands Combination =
1109 1109  
1110 1110  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1112,6 +1112,8 @@
1112 1112  * **AT+ADR=0 **~-~-> Disable ADR first
1113 1113  * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1114 1114  
1174 +
1175 +
1115 1115  == 8.2 Use Downlink Command to set a fix uplink DR ==
1116 1116  
1117 1117  {{info}}

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0