Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,11 +20,12 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
	22	+** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25	25	** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26	26
27	27
	27	+
28	28	= 3. Support End Node and firmware version =
29	29
30	30	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -99,7 +99,6 @@
99	99	)))
100	100
101	101
102		-
103	103	= 4. System Management Commands =
104	104
105	105	== 4.1 Change Uplink Interval ==
...	...	@@ -340,6 +340,7 @@
340	340	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
341	341
342	342
	342	+
343	343	== 5.3 Application Session Key ==
344	344
345	345	Feature: Get or Set the Application Session Key.
...	...	@@ -358,7 +358,6 @@
358	358	OK
359	359	)))
360	360
361		-
362	362	== 5.4 Device Address ==
363	363
364	364	Feature: Get or Set the Device Address.
...	...	@@ -377,7 +377,6 @@
377	377	)))
378	378	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
379	379
380		-
381	381	== 5.5 Device EUI ==
382	382
383	383	Feature: Get or Set the Device EUI.
...	...	@@ -396,7 +396,6 @@
396	396	OK
397	397	)))
398	398
399		-
400	400	== 5.6 Network ID ==
401	401
402	402	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -413,7 +413,6 @@
413	413	)))
414	414	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
415	415
416		-
417	417	== 5.7 Network Session Key ==
418	418
419	419	Feature: Get or Set the Network Session Key
...	...	@@ -430,7 +430,6 @@
430	430	)))
431	431	|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
432	432
433		-
434	434	= 6. Joining and sending date on LoRaWAN network =
435	435
436	436	== 6.1 Confirm Mode ==
...	...	@@ -459,7 +459,6 @@
459	459	* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
460	460	* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
461	461
462		-
463	463	== 6.2 Confirm Status ==
464	464
465	465	Feature: Get confirmation status of the last AT+SEND (0-1).
...	...	@@ -475,7 +475,6 @@
475	475	OK
476	476	)))
477	477
478		-
479	479	== 6.3 Join LoRa® Network ==
480	480
481	481	Feature: Join network.
...	...	@@ -810,7 +810,7 @@
810	810
811	811	)))
812	812
813		-== 7.11 Receive Delay2 ==
	806	+== 7.11Receive Delay2 ==
814	814
815	815	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
816	816
...	...	@@ -1015,8 +1015,6 @@
1015	1015
1016	1016	(((
1017	1017	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1018		-
1019		-
1020	1020	)))
1021	1021
1022	1022	== 7.21 Get or Set RXwindows2 timeout ==