<
From version < 38.81 >
edited by Xiaoling
on 2022/05/31 09:19
To version < 50.1 >
edited by Edwin Chen
on 2022/06/22 14:26
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Xiaoling
1 +XWiki.Edwin
Content
... ... @@ -24,7 +24,6 @@
24 24  ** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25 25  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26 26  
27 -
28 28  = 3. Support End Node and firmware version =
29 29  
30 30  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
... ... @@ -98,8 +98,6 @@
98 98  )))
99 99  )))
100 100  
101 -
102 -
103 103  = 4. System Management Commands =
104 104  
105 105  == 4.1 Change Uplink Interval ==
... ... @@ -138,8 +138,6 @@
138 138  * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
139 139  * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140 140  
141 -
142 -
143 143  == 4.2 Reboot End Node ==
144 144  
145 145  Feature: Reboot End Node to perform a new OTAA or ABP Join.
... ... @@ -335,7 +335,6 @@
335 335  )))
336 336  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
337 337  
338 -
339 339  == 5.3 Application Session Key ==
340 340  
341 341  Feature: Get or Set the Application Session Key.
... ... @@ -354,7 +354,6 @@
354 354  OK
355 355  )))
356 356  
357 -
358 358  == 5.4 Device Address ==
359 359  
360 360  Feature: Get or Set the Device Address.
... ... @@ -373,7 +373,6 @@
373 373  )))
374 374  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
375 375  
376 -
377 377  == 5.5 Device EUI ==
378 378  
379 379  Feature: Get or Set the Device EUI.
... ... @@ -392,7 +392,6 @@
392 392  OK
393 393  )))
394 394  
395 -
396 396  == 5.6 Network ID ==
397 397  
398 398  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
... ... @@ -409,7 +409,6 @@
409 409  )))
410 410  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
411 411  
412 -
413 413  == 5.7 Network Session Key ==
414 414  
415 415  Feature: Get or Set the Network Session Key
... ... @@ -426,11 +426,12 @@
426 426  )))
427 427  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
428 428  
429 -
430 430  = 6. Joining and sending date on LoRaWAN network =
431 431  
432 432  == 6.1 Confirm Mode ==
433 433  
423 +=== AT+CFM command before DR-LWS007 software stack ===
424 +
434 434  Feature: Get or Set the confirmation mode (0-1).
435 435  
436 436  {{info}}
... ... @@ -455,7 +455,54 @@
455 455  * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
456 456  * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
457 457  
449 +=== AT+CFM command since DR-LWS007 software stack ===
458 458  
451 +{{info}}
452 +**AT Command: AT+CFM**
453 +{{/info}}
454 +
455 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
456 +|=(% colspan="3" style="width: 707px;" %)AT+CFM
457 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
458 +|(% style="width:160px" %)(((
459 +AT+CFM=1,0,0
460 +
461 +value1
462 +)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
463 +1
464 +
465 +OK
466 +)))
467 +|(% style="width:160px" %)(((
468 +AT+CFM=0,?,0
469 +
470 +value2
471 +)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
472 +0~~7
473 +
474 +OK
475 +)))
476 +|(% style="width:160px" %)(((
477 +AT+CFM=0,0,1
478 +
479 +value3
480 +)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
481 +1
482 +
483 +OK
484 +)))
485 +
486 +{{info}}
487 +**Downlink Command: 0x05**
488 +{{/info}}
489 +
490 +Format: Command Code (0x05) followed by 2 bytes mode value.
491 +
492 +If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
493 +
494 +* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
495 +* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
496 +
459 459  == 6.2 Confirm Status ==
460 460  
461 461  Feature: Get confirmation status of the last AT+SEND (0-1).
... ... @@ -471,7 +471,6 @@
471 471  OK
472 472  )))
473 473  
474 -
475 475  == 6.3 Join LoRa® Network ==
476 476  
477 477  Feature: Join network.
... ... @@ -514,7 +514,7 @@
514 514  
515 515  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
516 516  
517 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
554 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
518 518  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
519 519  
520 520  == 6.5 LoRa® Network Join Status ==
... ... @@ -770,8 +770,10 @@
770 770  
771 771  == 7.9 Public Network Mode ==
772 772  
773 -Feature: Get or Set the public network mode. (0: off, 1: on)
810 +Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
774 774  
812 +Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
813 +
775 775  {{info}}
776 776  **AT Command:AT+PNM**
777 777  {{/info}}
... ... @@ -782,11 +782,16 @@
782 782  |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
783 783  OK
784 784  )))
785 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
824 +|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
825 +Set the public network mode.
826 +
827 +Set syncword=0x34
828 +)))|(% style="width:272px" %)(System will write new value to PNM)(((
786 786  OK
787 787  
788 788  
789 789  )))
833 +|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
790 790  
791 791  == 7.10 Receive Delay1 ==
792 792  
... ... @@ -1099,6 +1099,129 @@
1099 1099  * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1100 1100  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1101 1101  
1146 +== 7.24 Controls NBTrans in unconfirmed uplink mode(LWS007 NBTrans:Set retransmission packets) ==
1147 +
1148 +{{info}}
1149 +**AT Command: AT+SETMAXNBTRANS **
1150 +{{/info}}
1151 +
1152 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1153 +|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1154 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1155 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=1,0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1156 +OK
1157 +)))
1158 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=?,1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1159 +1
1160 +
1161 +OK
1162 +)))
1163 +
1164 +{{info}}
1165 +**Downlink Command: 0x33**
1166 +{{/info}}
1167 +
1168 +Format: Command Code (0x33) followed by 2 bytes mode value.
1169 +
1170 +If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1171 +
1172 +* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1173 +* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1174 +
1175 +== 7.25 Device offline rejoining (LWS007) ==
1176 +
1177 +{{info}}
1178 +**AT Command: AT+DDETECT**
1179 +{{/info}}
1180 +
1181 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1182 +|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1183 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1184 +|(% style="width:160px" %)(((
1185 +AT+DDETECT=1,1440,2880
1186 +
1187 +value1
1188 +)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1189 +1
1190 +
1191 +OK
1192 +)))
1193 +|(% style="width:160px" %)(((
1194 +AT+DDETECT=1,?,2880
1195 +
1196 +value2
1197 +)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1198 +
1199 +
1200 +OK
1201 +)))
1202 +|(% style="width:160px" %)(((
1203 +AT+DDETECT=1,1440,?
1204 +
1205 +value3
1206 +)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1207 +
1208 +
1209 +OK
1210 +)))
1211 +
1212 +{{info}}
1213 +**Downlink Command: 0x33**
1214 +{{/info}}
1215 +
1216 +Format: Command Code (0x32) followed by 2 bytes mode value.
1217 +
1218 +If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1219 +
1220 +* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1221 +
1222 +== 7.26 Request the server to send an ACK ==
1223 +
1224 +{{info}}
1225 +**AT Command: AT+PNACKMD**
1226 +{{/info}}
1227 +
1228 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1229 +|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1230 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1231 +|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1232 +OK
1233 +)))
1234 +|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1235 +0
1236 +
1237 +OK
1238 +)))
1239 +
1240 +== 7.27 Adjust network rejoining interval ==
1241 +
1242 +{{info}}
1243 +**AT Command: AT+RJTDC**
1244 +{{/info}}
1245 +
1246 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1247 +|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1248 +|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1249 +|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30000(((
1250 +OK
1251 +
1252 +the interval is 30000ms = 30s
1253 +)))
1254 +|(% style="width:165px" %)AT+RJTDC=60000|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1255 +Set the ReJoin data transmission interval to 60000ms = 60 seconds
1256 +)))
1257 +
1258 +{{info}}
1259 +**Downlink Command: 0x26**
1260 +{{/info}}
1261 +
1262 +Format: Command Code (0x26) followed by 2 bytes mode value.
1263 +
1264 +If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1265 +
1266 +* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1267 +* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1268 +
1102 1102  = 8. AT Commands Combination =
1103 1103  
1104 1104  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1117,3 +1117,4 @@
1117 1117  * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1118 1118  * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1119 1119  * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1287 +~)~)~)
Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0