Last modified by kai on 2024/09/06 10:00
<
From version < 38.79 >
edited by Xiaoling
on 2022/05/31 09:19
To version < 51.4 >
edited by Xiaoling
on 2022/07/13 14:10
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,4 @@
1 - **Contents：**
1 + **Table of** **Contents：**
2 2  
3 3  {{toc/}}
4 4  
... ... @@ -6,6 +6,7 @@
6 6  
7 7  = 1. Introduction =
8 8  
9 +
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10 10  
11 11  * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
... ... @@ -18,6 +18,7 @@
18 18  
19 19  = 2. How to use AT Commands or Downlink command =
20 20  
22 +
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 23  ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
... ... @@ -26,8 +26,10 @@
26 26  
27 27  
28 28  
31 +
29 29  = 3. Support End Node and firmware version =
30 30  
34 +
31 31  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
32 32  |=(% colspan="3" style="width: 963px;" %)(((
33 33  Dragino STM32 base hardware Firmware / LoRaWAN stack list
... ... @@ -100,17 +100,19 @@
100 100  )))
101 101  
102 102  
107 +
108 +
103 103  = 4. System Management Commands =
104 104  
111 +
105 105  == 4.1 Change Uplink Interval ==
106 106  
114 +
107 107  Feature: Change LoRaWAN End Node Transmit Interval.
108 108  
109 -(% class="box infomessage" %)
110 -(((
111 -**AT Command: AT+TDC**
112 -)))
113 113  
118 +(% style="color:blue" %)**AT Command: AT+TDC**
119 +
114 114  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
115 115  |=(% colspan="3" style="width: 724px;" %)AT+TDC
116 116  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
... ... @@ -123,11 +123,11 @@
123 123  Set transmit interval to 60000ms = 60 seconds
124 124  )))
125 125  
126 -{{info}}
127 -**Downlink Command: 0x01**
128 -{{/info}}
129 -
130 130  (((
133 +
134 +
135 +(% style="color:blue" %)**Downlink Command: 0x01**
136 +
131 131  Format: Command Code (0x01) followed by 3 bytes time value.
132 132  )))
133 133  
... ... @@ -139,14 +139,16 @@
139 139  * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140 140  
141 141  
148 +
149 +
142 142  == 4.2 Reboot End Node ==
143 143  
152 +
144 144  Feature: Reboot End Node to perform a new OTAA or ABP Join.
145 145  
146 -{{info}}
147 -**AT Command: ATZ**
148 -{{/info}}
149 149  
156 +(% style="color:blue" %)**AT Command: ATZ**
157 +
150 150  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
151 151  |=(% colspan="3" %)ATZ: Trig a reset of the MCU
152 152  |**Command Example**|**Function**|**Response**
... ... @@ -164,9 +164,7 @@
164 164  <followed by the Tx and Rx information>
165 165  )))
166 166  
167 -{{info}}
168 -**Downlink Command: 0x04**
169 -{{/info}}
175 +(% style="color:blue" %)**Downlink Command: 0x04**
170 170  
171 171  (((
172 172  Format: Command Code (0x04) followed by FF.
... ... @@ -180,12 +180,12 @@
180 180  
181 181  == 4.3 Reset to factory Default ==
182 182  
189 +
183 183  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
184 184  
185 -{{info}}
186 -**AT Command: AT+FDR**
187 -{{/info}}
188 188  
193 +(% style="color:blue" %)**AT Command: AT+FDR**
194 +
189 189  (% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
190 190  |=(% colspan="3" style="width: 828px;" %)Reset to factory default
191 191  |(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
... ... @@ -203,9 +203,7 @@
203 203  Please set the parameters or reset Device to apply change
204 204  )))
205 205  
206 -{{info}}
207 -**Downlink Command: 0x04**
208 -{{/info}}
212 +(% style="color:blue" %)**Downlink Command: 0x04**
209 209  
210 210  (((
211 211  Format: Command Code (0x04) followed by FE.
... ... @@ -218,12 +218,12 @@
218 218  
219 219  == 4.4 Show Firmware Version ==
220 220  
225 +
221 221  Feature: Show firmware version. No downlink command yet.
222 222  
223 -{{info}}
224 -**AT Command: AT+VER**
225 -{{/info}}
226 226  
229 +(% style="color:blue" %)**AT Command: AT+VER**
230 +
227 227  (% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
228 228  |=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
229 229  |(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -233,9 +233,7 @@
233 233  OK
234 234  )))
235 235  
236 -{{info}}
237 -**Downlink Command: 0x26 (Valid in 006 stack)**
238 -{{/info}}
240 +(% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
239 239  
240 240  (((
241 241  Downlink Format: 0x26
... ... @@ -246,6 +246,9 @@
246 246  )))
247 247  
248 248  (((
251 +
252 +
253 +
249 249  **xx: Software Type:**
250 250  )))
251 251  
... ... @@ -254,6 +254,8 @@
254 254  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
255 255  
256 256  (((
262 +
263 +
257 257  **yy: Frequency Band:**
258 258  )))
259 259  
... ... @@ -269,6 +269,8 @@
269 269  * 0xa0: AS923-3
270 270  
271 271  (((
279 +
280 +
272 272  **zz: Subband**
273 273  )))
274 274  
... ... @@ -277,12 +277,12 @@
277 277  
278 278  == 4.5 Show System Configure ==
279 279  
289 +
280 280  Feature: Show All configure. No downlink command yet.
281 281  
282 -{{info}}
283 -**AT Command: AT+CFG**
284 -{{/info}}
285 285  
293 +(% style="color:blue" %)**AT Command: AT+CFG**
294 +
286 286  (% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
287 287  |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
288 288  |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
... ... @@ -301,16 +301,18 @@
301 301  )))
302 302  
303 303  
313 +
304 304  = 5. Keys, IDs and EUIs management =
305 305  
316 +
306 306  == 5.1 Application EUI ==
307 307  
319 +
308 308  Feature: Get or Set the Application EUI.
309 309  
310 -{{info}}
311 -**AT Command: AT+APPEUI**
312 -{{/info}}
313 313  
323 +(% style="color:blue" %)**AT Command: AT+APPEUI**
324 +
314 314  (% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
315 315  |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
316 316  |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
... ... @@ -320,14 +320,15 @@
320 320  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
321 321  
322 322  
334 +
323 323  == 5.2 Application Key ==
324 324  
337 +
325 325  Feature: Get or Set the Application Key.
326 326  
327 -{{info}}
328 -**AT Command: AT+APPKEY**
329 -{{/info}}
330 330  
341 +(% style="color:blue" %)**AT Command: AT+APPKEY**
342 +
331 331  (% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
332 332  |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
333 333  |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
... ... @@ -340,12 +340,12 @@
340 340  
341 341  == 5.3 Application Session Key ==
342 342  
355 +
343 343  Feature: Get or Set the Application Session Key.
344 344  
345 -{{info}}
346 -**AT Command: AT+APPSKEY**
347 -{{/info}}
348 348  
359 +(% style="color:blue" %)**AT Command: AT+APPSKEY**
360 +
349 349  (% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
350 350  |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
351 351  |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
... ... @@ -356,16 +356,14 @@
356 356  OK
357 357  )))
358 358  
359 -
360 -
361 361  == 5.4 Device Address ==
362 362  
373 +
363 363  Feature: Get or Set the Device Address.
364 364  
365 -{{info}}
366 -**AT Command: AT+DADDR**
367 -{{/info}}
368 368  
377 +(% style="color:blue" %)**AT Command: AT+DADDR**
378 +
369 369  (% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
370 370  |=(% colspan="3" style="width: 792px;" %)AT+DADDR
371 371  |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
... ... @@ -376,16 +376,14 @@
376 376  )))
377 377  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
378 378  
379 -
380 -
381 381  == 5.5 Device EUI ==
382 382  
391 +
383 383  Feature: Get or Set the Device EUI.
384 384  
385 -{{info}}
386 -**AT Command: AT+DEUI**
387 -{{/info}}
388 388  
395 +(% style="color:blue" %)**AT Command: AT+DEUI**
396 +
389 389  (% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
390 390  |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
391 391  |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
... ... @@ -396,16 +396,14 @@
396 396  OK
397 397  )))
398 398  
399 -
400 -
401 401  == 5.6 Network ID ==
402 402  
409 +
403 403  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
404 404  
405 -{{info}}
406 -**AT Command: AT+NWKID**
407 -{{/info}}
408 408  
413 +(% style="color:blue" %)**AT Command: AT+NWKID**
414 +
409 409  (% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
410 410  |=(% colspan="3" style="width: 445px;" %)AT+NWKID
411 411  |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
... ... @@ -414,16 +414,14 @@
414 414  )))
415 415  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
416 416  
417 -
418 -
419 419  == 5.7 Network Session Key ==
420 420  
425 +
421 421  Feature: Get or Set the Network Session Key
422 422  
423 -{{info}}
424 -**AT Command: AT+NWKSKEY**
425 -{{/info}}
426 426  
429 +(% style="color:blue" %)**AT Command: AT+NWKSKEY**
430 +
427 427  (% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
428 428  |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
429 429  |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
... ... @@ -432,18 +432,20 @@
432 432  )))
433 433  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
434 434  
435 -
436 -
437 437  = 6. Joining and sending date on LoRaWAN network =
438 438  
441 +
439 439  == 6.1 Confirm Mode ==
440 440  
444 +
445 +=== 6.1.1  AT+CFM command before DR-LWS007 software stack ===
446 +
447 +
441 441  Feature: Get or Set the confirmation mode (0-1).
442 442  
443 -{{info}}
444 -**AT Command: AT+CFM**
445 -{{/info}}
446 446  
451 +(% style="color:blue" %)**AT Command: AT+CFM**
452 +
447 447  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
448 448  |=(% colspan="3" style="width: 707px;" %)AT+CFM
449 449  |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
... ... @@ -453,7 +453,7 @@
453 453  |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
454 454  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
455 455  
456 -Downlink Command: 0x05
462 +(% style="color:blue" %)**Downlink Command: 0x05**
457 457  
458 458  Format: Command Code (0x05) followed by 2 bytes mode value.
459 459  
... ... @@ -463,15 +463,60 @@
463 463  * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
464 464  
465 465  
472 +=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
466 466  
474 +
475 +(% style="color:blue" %)**AT Command: AT+CFM**
476 +
477 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
478 +|=(% colspan="3" style="width: 707px;" %)AT+CFM
479 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
480 +|(% style="width:160px" %)(((
481 +AT+CFM=1,0,0
482 +
483 +value1
484 +)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
485 +1
486 +
487 +OK
488 +)))
489 +|(% style="width:160px" %)(((
490 +AT+CFM=0,?,0
491 +
492 +value2
493 +)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
494 +0~~7
495 +
496 +OK
497 +)))
498 +|(% style="width:160px" %)(((
499 +AT+CFM=0,0,1
500 +
501 +value3
502 +)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
503 +1
504 +
505 +OK
506 +)))
507 +
508 +(% style="color:blue" %)**Downlink Command: 0x05**
509 +
510 +Format: Command Code (0x05) followed by 2 bytes mode value.
511 +
512 +If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
513 +
514 +* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
515 +* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
516 +
517 +
467 467  == 6.2 Confirm Status ==
468 468  
520 +
469 469  Feature: Get confirmation status of the last AT+SEND (0-1).
470 470  
471 -{{info}}
472 -**AT Command: AT+CFS**
473 -{{/info}}
474 474  
524 +(% style="color:blue" %)**AT Command: AT+CFS**
525 +
475 475  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
476 476  |=(% colspan="3" style="width: 531px;" %)AT+CFS
477 477  |(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
... ... @@ -479,16 +479,14 @@
479 479  OK
480 480  )))
481 481  
482 -
483 -
484 484  == 6.3 Join LoRa® Network ==
485 485  
535 +
486 486  Feature: Join network.
487 487  
488 -{{info}}
489 -**AT Command: AT+JOIN**
490 -{{/info}}
491 491  
539 +(% style="color:blue" %)**AT Command: AT+JOIN**
540 +
492 492  (% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
493 493  |=(% colspan="3" style="width: 644px;" %)AT+JOIN
494 494  |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
... ... @@ -498,15 +498,14 @@
498 498  While Error in format, return AT_BUSY_ERROR
499 499  )))
500 500  
501 -
502 502  == 6.4 LoRa® Network Join Mode ==
503 503  
552 +
504 504  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
505 505  
506 -{{info}}
507 -**AT Command: AT+NJM**
508 -{{/info}}
509 509  
556 +(% style="color:blue" %)**AT Command: AT+NJM**
557 +
510 510  (% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
511 511  |=(% colspan="3" style="width: 750px;" %)AT+NJM
512 512  |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
... ... @@ -516,26 +516,24 @@
516 516  |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
517 517  |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
518 518  
519 -{{info}}
520 -**Downlink Command: 0x20**
521 -{{/info}}
567 +(% style="color:blue" %)**Downlink Command: 0x20**
522 522  
523 523  Format: Command Code (0x20) followed by 1 bytes mode value.
524 524  
525 525  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
526 526  
527 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
573 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
528 528  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
529 529  
530 530  
531 531  == 6.5 LoRa® Network Join Status ==
532 532  
579 +
533 533  Feature: LoRa® Network Join Status.
534 534  
535 -{{info}}
536 -**AT Command: AT+NJS**
537 -{{/info}}
538 538  
583 +(% style="color:blue" %)**AT Command: AT+NJS**
584 +
539 539  (% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
540 540  |=(% colspan="3" style="width: 495px;" %)AT+NJS
541 541  |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
... ... @@ -543,15 +543,14 @@
543 543  OK
544 544  )))
545 545  
546 -
547 547  == 6.6 Print Last Received Data in Raw Format ==
548 548  
594 +
549 549  Feature: Print Last Received Data in Raw Format<port:data>.
550 550  
551 -{{info}}
552 -**AT Command: AT+RECV**
553 -{{/info}}
554 554  
598 +(% style="color:blue" %)**AT Command: AT+RECV**
599 +
555 555  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
556 556  |=(% colspan="3" style="width: 584px;" %)AT+RECV
557 557  |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -559,15 +559,14 @@
559 559  OK
560 560  )))
561 561  
562 -
563 563  == 6.7 Print Last Received Data in Binary Format ==
564 564  
609 +
565 565  Feature: Print Last Received Data in Binary Format<port:data>.
566 566  
567 -{{info}}
568 -**AT Command: AT+RECVB**
569 -{{/info}}
570 570  
613 +(% style="color:blue" %)**AT Command: AT+RECVB**
614 +
571 571  (% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
572 572  |=(% colspan="3" style="width: 790px;" %)AT+RECVB
573 573  |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
... ... @@ -575,15 +575,14 @@
575 575  OK
576 576  )))
577 577  
578 -
579 579  == 6.8 Send Text Data ==
580 580  
624 +
581 581  Feature: Send Text Data<port:data>.
582 582  
583 -{{info}}
584 -**AT Command: AT+SEND**
585 -{{/info}}
586 586  
628 +(% style="color:blue" %)**AT Command: AT+SEND**
629 +
587 587  (% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
588 588  |=(% colspan="3" style="width: 988px;" %)AT+SEND
589 589  |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
... ... @@ -595,15 +595,14 @@
595 595  
596 596  )))
597 597  
598 -
599 599  == 6.9 Send Hexadecimal Data ==
600 600  
643 +
601 601  Feature: Send hexadecimal data along with the application port.
602 602  
603 -{{info}}
604 -**AT Command: AT+SENDB**
605 -{{/info}}
606 606  
647 +(% style="color:blue" %)**AT Command: AT+SENDB**
648 +
607 607  (% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
608 608  |=(% colspan="3" style="width: 1117px;" %)AT+SENDB
609 609  |(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
... ... @@ -614,17 +614,17 @@
614 614  
615 615  )))
616 616  
617 -
618 618  = 7. LoRaWAN network management =
619 619  
661 +
620 620  == 7.1 Adaptive Data Rate ==
621 621  
664 +
622 622  Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
623 623  
624 -{{info}}
625 -**AT Command: AT+ADR**
626 -{{/info}}
627 627  
668 +(% style="color:blue" %)**AT Command: AT+ADR**
669 +
628 628  (% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
629 629  |=(% colspan="3" style="width: 680px;" %)AT+ADR
630 630  |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
... ... @@ -636,25 +636,22 @@
636 636  AT_PARAM_ERROR
637 637  )))
638 638  
639 -{{info}}
640 -**Downlink Command: 0x22**
641 -{{/info}}
681 +(% style="color:blue" %)**Downlink Command: 0x22**
642 642  
643 -
644 644  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
645 645  
646 -* **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
685 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
647 647  * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
648 648  
649 649  
650 650  == 7.2 LoRa® Class ==
651 651  
691 +
652 652  Feature: Get or Set the Device Class(Currently only support class A, class C).
653 653  
654 -{{info}}
655 -**AT Command:AT+CLASS**
656 -{{/info}}
657 657  
695 +(% style="color:blue" %)**AT Command:AT+CLASS**
696 +
658 658  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
659 659  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
660 660  |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
... ... @@ -665,15 +665,14 @@
665 665  
666 666  )))
667 667  
668 -
669 669  == 7.3 Duty Cycle Setting ==
670 670  
709 +
671 671  Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
672 672  
673 -{{info}}
674 -**AT Command:AT+DCS**
675 -{{/info}}
676 676  
713 +(% style="color:blue" %)**AT Command:AT+DCS**
714 +
677 677  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
678 678  |=(% colspan="3" style="width: 512px;" %)AT+DCS
679 679  |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
... ... @@ -684,15 +684,14 @@
684 684  
685 685  )))
686 686  
687 -
688 688  == 7.4 Data Rate ==
689 689  
727 +
690 690  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
691 691  
692 -{{info}}
693 -**AT Command: AT+DR**
694 -{{/info}}
695 695  
731 +(% style="color:blue" %)**AT Command: AT+DR**
732 +
696 696  (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
697 697  |=(% colspan="3" style="width: 463px;" %)AT+DR
698 698  |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -703,11 +703,8 @@
703 703  
704 704  )))
705 705  
706 -{{info}}
707 -**Downlink Command: 0x2200aaFF**
708 -{{/info}}
743 +(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
709 709  
710 -
711 711  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
712 712  
713 713  * **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
... ... @@ -716,12 +716,12 @@
716 716  
717 717  == 7.5 Frame Counter Downlink ==
718 718  
753 +
719 719  Feature: Get or Set the Frame Counter Downlink.
720 720  
721 -{{info}}
722 -**AT Command:AT+FCD**
723 -{{/info}}
724 724  
757 +(% style="color:blue" %)**AT Command:AT+FCD**
758 +
725 725  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
726 726  |=(% colspan="3" style="width: 690px;" %)AT+FCD
727 727  |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
... ... @@ -730,19 +730,15 @@
730 730  )))
731 731  |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
732 732  OK
733 -
734 -
735 735  )))
736 736  
737 -
738 738  == 7.6 Frame Counter Uplink ==
739 739  
740 740  Feature: Get or Set the Frame Counter Uplink.
741 741  
742 -{{info}}
743 -**AT Command:AT+FCU**
744 -{{/info}}
745 745  
774 +(% style="color:blue" %)**AT Command:AT+FCU**
775 +
746 746  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
747 747  |=(% colspan="3" style="width: 531px;" %)AT+FCU
748 748  |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -753,15 +753,14 @@
753 753  
754 754  )))
755 755  
756 -
757 757  == 7.7 Join Accept Delay1 ==
758 758  
788 +
759 759  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
760 760  
761 -{{info}}
762 -**AT Command:AT+JN1DL**
763 -{{/info}}
764 764  
792 +(% style="color:blue" %)**AT Command:AT+JN1DL**
793 +
765 765  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
766 766  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
767 767  |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -772,15 +772,13 @@
772 772  
773 773  )))
774 774  
775 -
776 776  == 7.8 Join Accept Delay2 ==
777 777  
778 778  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
779 779  
780 -{{info}}
781 -**AT Command:AT+JN2DL**
782 -{{/info}}
783 783  
809 +(% style="color:blue" %)**AT Command:AT+JN2DL**
810 +
784 784  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
785 785  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
786 786  |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
... ... @@ -791,15 +791,16 @@
791 791  
792 792  )))
793 793  
794 -
795 795  == 7.9 Public Network Mode ==
796 796  
797 -Feature: Get or Set the public network mode. (0: off, 1: on)
798 798  
799 -{{info}}
800 -**AT Command:AT+PNM**
801 -{{/info}}
824 +Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
802 802  
826 +(% style="color:red" %)Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
827 +
828 +
829 +(% style="color:blue" %)**AT Command:AT+PNM**
830 +
803 803  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
804 804  |=(% colspan="3" style="width: 664px;" %)AT+PNM
805 805  |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
... ... @@ -806,21 +806,25 @@
806 806  |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
807 807  OK
808 808  )))
809 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
837 +|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
838 +Set the public network mode.
839 +
840 +Set syncword=0x34
841 +)))|(% style="width:272px" %)(System will write new value to PNM)(((
810 810  OK
811 811  
812 812  
813 813  )))
846 +|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
814 814  
815 -
816 816  == 7.10 Receive Delay1 ==
817 817  
850 +
818 818  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
819 819  
820 -{{info}}
821 -**AT Command:AT+RX1DL**
822 -{{/info}}
823 823  
854 +(% style="color:blue" %)**AT Command:AT+RX1DL**
855 +
824 824  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
825 825  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
826 826  |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -834,12 +834,12 @@
834 834  
835 835  == 7.11 Receive Delay2 ==
836 836  
869 +
837 837  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
838 838  
839 -{{info}}
840 -**AT Command:AT+RX2DL**
841 -{{/info}}
842 842  
873 +(% style="color:blue" %)**AT Command:AT+RX2DL**
874 +
843 843  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
844 844  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
845 845  |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -853,12 +853,12 @@
853 853  
854 854  == 7.12 Rx2 Window Data Rate ==
855 855  
888 +
856 856  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
857 857  
858 -{{info}}
859 -**AT Command:AT+RX2DR**
860 -{{/info}}
861 861  
892 +(% style="color:blue" %)**AT Command:AT+RX2DR**
893 +
862 862  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
863 863  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
864 864  |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
... ... @@ -872,12 +872,12 @@
872 872  
873 873  == 7.13 Rx2 Window Frequency ==
874 874  
907 +
875 875  Feature: Get or Set the Rx2 window frequency
876 876  
877 -{{info}}
878 -**AT Command:AT+RX2FQ**
879 -{{/info}}
880 880  
911 +(% style="color:blue" %)**AT Command:AT+RX2FQ**
912 +
881 881  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
882 882  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
883 883  |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
... ... @@ -891,12 +891,12 @@
891 891  
892 892  == 7.14 Transmit Power ==
893 893  
926 +
894 894  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
895 895  
896 -{{info}}
897 -**AT Command:AT+TXP**
898 -{{/info}}
899 899  
930 +(% style="color:blue" %)**AT Command:AT+TXP**
931 +
900 900  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
901 901  |=(% colspan="3" style="width: 462px;" %)AT+TXP
902 902  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -915,14 +915,15 @@
915 915  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
916 916  
917 917  
950 +
918 918  == 7.15 RSSI of the Last Received Packet ==
919 919  
953 +
920 920  Feature: Get or Set the Rx2 window frequency
921 921  
922 -{{info}}
923 -**AT Command:AT+RSSI**
924 -{{/info}}
925 925  
957 +(% style="color:blue" %)**AT Command:AT+RSSI**
958 +
926 926  (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
927 927  |=(% colspan="3" style="width: 554px;" %)AT+RSSI
928 928  |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
... ... @@ -933,12 +933,12 @@
933 933  
934 934  == 7.16 SNR of the Last Received Packet ==
935 935  
969 +
936 936  Feature: Get the SNR of the last received packet
937 937  
938 -{{info}}
939 -**AT Command:AT+SNR**
940 -{{/info}}
941 941  
973 +(% style="color:blue" %)**AT Command:AT+SNR**
974 +
942 942  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
943 943  |=(% colspan="3" style="width: 568px;" %)AT+SNR
944 944  |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -949,12 +949,12 @@
949 949  
950 950  == 7.17 Application Port ==
951 951  
985 +
952 952  Feature: Get or set the application port.
953 953  
954 -{{info}}
955 -**AT Command: AT+PORT**
956 -{{/info}}
957 957  
989 +(% style="color:blue" %)**AT Command: AT+PORT**
990 +
958 958  (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
959 959  |=(% colspan="3" style="width: 497px;" %)AT+PORT
960 960  |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
... ... @@ -963,9 +963,7 @@
963 963  )))
964 964  |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
965 965  
966 -{{info}}
967 -**Downlink Command: 0x23**
968 -{{/info}}
999 +(% style="color:blue" %)**Downlink Command: 0x23**
969 969  
970 970  Format: Command Code (0x23) followed by 1 bytes port value.
971 971  
... ... @@ -975,14 +975,15 @@
975 975  * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
976 976  
977 977  
1009 +
978 978  == 7.18 Single Channel Mode ==
979 979  
1012 +
980 980  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
981 981  
982 -{{info}}
983 -**AT Command: AT+CHS**
984 -{{/info}}
985 985  
1016 +(% style="color:blue" %)**AT Command: AT+CHS**
1017 +
986 986  (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
987 987  |=(% colspan="3" style="width: 600px;" %)AT+CHS
988 988  |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -996,10 +996,9 @@
996 996  
997 997  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
998 998  
999 -{{info}}
1000 -**AT Command: AT+CHE**
1001 -{{/info}}
1002 1002  
1032 +(% style="color:blue" %)**AT Command: AT+CHE**
1033 +
1003 1003  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1004 1004  |=(% colspan="3" style="width: 707px;" %)AT+CHE
1005 1005  |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
... ... @@ -1010,9 +1010,7 @@
1010 1010  )))
1011 1011  |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1012 1012  
1013 -{{info}}
1014 -**Downlink Command: 0x24**
1015 -{{/info}}
1044 +(% style="color:blue" %)**Downlink Command: 0x24**
1016 1016  
1017 1017  Format: Command Code (0x24) followed by 1 bytes channel value.
1018 1018  
... ... @@ -1022,14 +1022,15 @@
1022 1022  * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1023 1023  
1024 1024  
1054 +
1025 1025  == 7.20 Get or Set RXwindows1 timeout ==
1026 1026  
1027 -Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1028 1028  
1029 -{{info}}
1030 -**AT Command: AT+RX1WTO**
1031 -{{/info}}
1058 +Feature: Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1032 1032  
1060 +
1061 +(% style="color:blue" %)**AT Command: AT+RX1WTO**
1062 +
1033 1033  (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1034 1034  |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1035 1035  |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
... ... @@ -1039,11 +1039,16 @@
1039 1039  |(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
1040 1040  
1041 1041  (((
1072 +
1073 +
1042 1042  **AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1075 +
1076 +
1043 1043  )))
1044 1044  
1045 1045  [[image:image-20220526162535-1.png]]
1046 1046  
1081 +
1047 1047  (((
1048 1048  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1049 1049  
... ... @@ -1052,12 +1052,12 @@
1052 1052  
1053 1053  == 7.21 Get or Set RXwindows2 timeout ==
1054 1054  
1055 -Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1056 1056  
1057 -{{info}}
1058 -**AT Command: AT+RX2WTO**
1059 -{{/info}}
1091 +Feature: Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1060 1060  
1093 +
1094 +(% style="color:blue" %)**AT Command: AT+RX2WTO**
1095 +
1061 1061  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1062 1062  |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1063 1063  |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
... ... @@ -1069,12 +1069,12 @@
1069 1069  
1070 1070  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1071 1071  
1107 +
1072 1072  Feature: Get or Set uplinkdwelltime
1073 1073  
1074 -{{info}}
1075 -**AT Command: AT+DWELLT**
1076 -{{/info}}
1077 1077  
1111 +(% style="color:blue" %)**AT Command: AT+DWELLT**
1112 +
1078 1078  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1079 1079  |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1080 1080  |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
... ... @@ -1083,9 +1083,7 @@
1083 1083  )))
1084 1084  |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1085 1085  
1086 -{{info}}
1087 -**Downlink Command: 0x25**
1088 -{{/info}}
1121 +(% style="color:blue" %)**Downlink Command: 0x25**
1089 1089  
1090 1090  Format: Command Code (0x25) followed by 1 bytes state value.
1091 1091  
... ... @@ -1095,10 +1095,13 @@
1095 1095  * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1096 1096  
1097 1097  
1131 +
1098 1098  == 7.23 Set Packet Receiving Response Level ==
1099 1099  
1134 +
1100 1100  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
1101 1101  
1137 +
1102 1102  RPL value:
1103 1103  
1104 1104  * **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
... ... @@ -1107,6 +1107,7 @@
1107 1107  * **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1108 1108  * **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1109 1109  
1146 +
1110 1110  Case Analyes:
1111 1111  
1112 1112  * For Class A devices, AT+RPL=0 is ok. that is defaut settings in software.
... ... @@ -1113,10 +1113,9 @@
1113 1113  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1114 1114  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1115 1115  
1116 -{{info}}
1117 -**AT Command: AT+RPL**
1118 -{{/info}}
1119 1119  
1154 +(% style="color:blue" %)**AT Command: AT+RPL**
1155 +
1120 1120  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1121 1121  |=(% colspan="3" style="width: 533px;" %)AT+RPL
1122 1122  |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
... ... @@ -1125,9 +1125,7 @@
1125 1125  )))
1126 1126  |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1127 1127  
1128 -{{info}}
1129 -**Downlink Command: 0x21**
1130 -{{/info}}
1164 +(% style="color:blue" %)**Downlink Command: 0x21**
1131 1131  
1132 1132  Format: Command Code (0x21) followed by 1 bytes level value.
1133 1133  
... ... @@ -1137,22 +1137,145 @@
1137 1137  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1138 1138  
1139 1139  
1174 +
1175 +== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1176 +
1177 +
1178 +(% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1179 +
1180 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1181 +|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1182 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1183 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1184 +OK
1185 +)))
1186 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1187 +1
1188 +
1189 +OK
1190 +)))
1191 +
1192 +(% style="color:blue" %)**Downlink Command: 0x33**
1193 +
1194 +Format: Command Code (0x33) followed by 2 bytes mode value.
1195 +
1196 +If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1197 +
1198 +* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1199 +* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1200 +
1201 +
1202 +
1203 +== 7.25 Device offline rejoining （LWS007) ==
1204 +
1205 +
1206 +(% style="color:blue" %)**AT Command: AT+DDETECT**
1207 +
1208 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1209 +|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1210 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1211 +|(% style="width:160px" %)(((
1212 +AT+DDETECT=1,1440,2880
1213 +
1214 +value1
1215 +)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1216 +1
1217 +
1218 +OK
1219 +)))
1220 +|(% style="width:160px" %)(((
1221 +AT+DDETECT=1,?,2880
1222 +
1223 +value2
1224 +)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1225 +
1226 +
1227 +OK
1228 +)))
1229 +|(% style="width:160px" %)(((
1230 +AT+DDETECT=1,1440,？
1231 +
1232 +value3
1233 +)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1234 +
1235 +
1236 +OK
1237 +)))
1238 +
1239 +(% style="color:blue" %)**Downlink Command: 0x33**
1240 +
1241 +Format: Command Code (0x32) followed by 2 bytes mode value.
1242 +
1243 +If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1244 +
1245 +* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1246 +
1247 +
1248 +
1249 +== 7.26 Request the server to send an ACK ==
1250 +
1251 +
1252 +(% style="color:blue" %)**AT Command: AT+PNACKMD**
1253 +
1254 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1255 +|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1256 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1257 +|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1258 +OK
1259 +)))
1260 +|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1261 +0
1262 +
1263 +OK
1264 +)))
1265 +
1266 +
1267 +== 7.27 Adjust network rejoining interval ==
1268 +
1269 +
1270 +(% style="color:blue" %)**AT Command: AT+RJTDC**
1271 +
1272 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1273 +|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1274 +|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1275 +|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30000(((
1276 +OK
1277 +
1278 +the interval is 30000ms = 30s
1279 +)))
1280 +|(% style="width:165px" %)AT+RJTDC=60000|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1281 +Set the ReJoin data transmission interval to 60000ms = 60 seconds
1282 +)))
1283 +
1284 +(% style="color:blue" %)**Downlink Command: 0x26**
1285 +
1286 +Format: Command Code (0x26) followed by 2 bytes mode value.
1287 +
1288 +If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1289 +
1290 +* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1291 +* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1292 +
1293 +
1294 +
1140 1140  = 8. AT Commands Combination =
1141 1141  
1297 +
1142 1142  == 8.1 Set a fix RX2DR for downlink window ==
1143 1143  
1144 -* **AT+ADR=0 **~-~-> Disable ADR first
1145 -* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1146 1146  
1301 +* **AT+ADR=0             ** **~-~->**  Disable ADR first
1302 +* **AT+RX2DR=xxxx**  **~-~->**  Set xxxx to your wanted DataRate
1147 1147  
1304 +
1305 +
1148 1148  == 8.2 Use Downlink Command to set a fix uplink DR ==
1149 1149  
1150 -{{info}}
1151 -**Downlink Command: 0x22000500**
1152 -{{/info}}
1153 1153  
1154 -Same as:
1309 +(% style="color:blue" %)**Downlink Command: 0x22000500**
1155 1155  
1311 +**Same as:**
1312 +
1156 1156  * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1157 1157  * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1158 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1315 +* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0