Last modified by kai on 2024/09/06 10:00
<
From version < 38.78 >
edited by Xiaoling
on 2022/05/31 09:19
To version < 21.1 >
edited by Xiaoling
on 2022/05/27 17:53
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -3,7 +3,6 @@
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
... ... @@ -20,10 +20,11 @@
20 20  
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
22 +** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
23 +** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25 25  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26 26  
26 +
27 27  = 3. Support End Node and firmware version =
28 28  
29 29  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
... ... @@ -98,6 +98,7 @@
98 98  )))
99 99  
100 100  
101 +
101 101  = 4. System Management Commands =
102 102  
103 103  == 4.1 Change Uplink Interval ==
... ... @@ -335,7 +335,6 @@
335 335  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
336 336  
337 337  
338 -
339 339  == 5.3 Application Session Key ==
340 340  
341 341  Feature: Get or Set the Application Session Key.
... ... @@ -497,6 +497,7 @@
497 497  )))
498 498  
499 499  
500 +
500 500  == 6.4 LoRa® Network Join Mode ==
501 501  
502 502  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
... ... @@ -526,6 +526,7 @@
526 526  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
527 527  
528 528  
530 +
529 529  == 6.5 LoRa® Network Join Status ==
530 530  
531 531  Feature: LoRa® Network Join Status.
... ... @@ -542,6 +542,7 @@
542 542  )))
543 543  
544 544  
547 +
545 545  == 6.6 Print Last Received Data in Raw Format ==
546 546  
547 547  Feature: Print Last Received Data in Raw Format<port:data>.
... ... @@ -558,6 +558,7 @@
558 558  )))
559 559  
560 560  
564 +
561 561  == 6.7 Print Last Received Data in Binary Format ==
562 562  
563 563  Feature: Print Last Received Data in Binary Format<port:data>.
... ... @@ -574,6 +574,7 @@
574 574  )))
575 575  
576 576  
581 +
577 577  == 6.8 Send Text Data ==
578 578  
579 579  Feature: Send Text Data<port:data>.
... ... @@ -594,6 +594,7 @@
594 594  )))
595 595  
596 596  
602 +
597 597  == 6.9 Send Hexadecimal Data ==
598 598  
599 599  Feature: Send hexadecimal data along with the application port.
... ... @@ -613,6 +613,7 @@
613 613  )))
614 614  
615 615  
622 +
616 616  = 7. LoRaWAN network management =
617 617  
618 618  == 7.1 Adaptive Data Rate ==
... ... @@ -645,6 +645,7 @@
645 645  * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
646 646  
647 647  
655 +
648 648  == 7.2 LoRa® Class ==
649 649  
650 650  Feature: Get or Set the Device Class(Currently only support class A, class C).
... ... @@ -664,6 +664,7 @@
664 664  )))
665 665  
666 666  
675 +
667 667  == 7.3 Duty Cycle Setting ==
668 668  
669 669  Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
... ... @@ -683,6 +683,7 @@
683 683  )))
684 684  
685 685  
695 +
686 686  == 7.4 Data Rate ==
687 687  
688 688  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
... ... @@ -712,6 +712,7 @@
712 712  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
713 713  
714 714  
725 +
715 715  == 7.5 Frame Counter Downlink ==
716 716  
717 717  Feature: Get or Set the Frame Counter Downlink.
... ... @@ -733,6 +733,7 @@
733 733  )))
734 734  
735 735  
747 +
736 736  == 7.6 Frame Counter Uplink ==
737 737  
738 738  Feature: Get or Set the Frame Counter Uplink.
... ... @@ -752,6 +752,7 @@
752 752  )))
753 753  
754 754  
767 +
755 755  == 7.7 Join Accept Delay1 ==
756 756  
757 757  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
... ... @@ -771,6 +771,7 @@
771 771  )))
772 772  
773 773  
787 +
774 774  == 7.8 Join Accept Delay2 ==
775 775  
776 776  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
... ... @@ -790,6 +790,7 @@
790 790  )))
791 791  
792 792  
807 +
793 793  == 7.9 Public Network Mode ==
794 794  
795 795  Feature: Get or Set the public network mode. (0: off, 1: on)
... ... @@ -811,6 +811,7 @@
811 811  )))
812 812  
813 813  
829 +
814 814  == 7.10 Receive Delay1 ==
815 815  
816 816  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
... ... @@ -830,6 +830,7 @@
830 830  )))
831 831  
832 832  
849 +
833 833  == 7.11 Receive Delay2 ==
834 834  
835 835  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
... ... @@ -849,6 +849,7 @@
849 849  )))
850 850  
851 851  
869 +
852 852  == 7.12 Rx2 Window Data Rate ==
853 853  
854 854  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
... ... @@ -868,6 +868,7 @@
868 868  )))
869 869  
870 870  
889 +
871 871  == 7.13 Rx2 Window Frequency ==
872 872  
873 873  Feature: Get or Set the Rx2 window frequency
... ... @@ -887,6 +887,7 @@
887 887  )))
888 888  
889 889  
909 +
890 890  == 7.14 Transmit Power ==
891 891  
892 892  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
... ... @@ -913,6 +913,7 @@
913 913  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
914 914  
915 915  
936 +
916 916  == 7.15 RSSI of the Last Received Packet ==
917 917  
918 918  Feature: Get or Set the Rx2 window frequency
... ... @@ -929,6 +929,7 @@
929 929  )))
930 930  
931 931  
953 +
932 932  == 7.16 SNR of the Last Received Packet ==
933 933  
934 934  Feature: Get the SNR of the last received packet
... ... @@ -945,6 +945,7 @@
945 945  )))
946 946  
947 947  
970 +
948 948  == 7.17 Application Port ==
949 949  
950 950  Feature: Get or set the application port.
... ... @@ -973,6 +973,7 @@
973 973  * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
974 974  
975 975  
999 +
976 976  == 7.18 Single Channel Mode ==
977 977  
978 978  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
... ... @@ -990,6 +990,7 @@
990 990  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
991 991  
992 992  
1017 +
993 993  == 7.19 Eight Channel Mode ==
994 994  
995 995  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
... ... @@ -1020,6 +1020,7 @@
1020 1020  * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1021 1021  
1022 1022  
1048 +
1023 1023  == 7.20 Get or Set RXwindows1 timeout ==
1024 1024  
1025 1025  Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
... ... @@ -1065,6 +1065,7 @@
1065 1065  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1066 1066  
1067 1067  
1094 +
1068 1068  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1069 1069  
1070 1070  Feature: Get or Set uplinkdwelltime
... ... @@ -1093,6 +1093,7 @@
1093 1093  * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1094 1094  
1095 1095  
1123 +
1096 1096  == 7.23 Set Packet Receiving Response Level ==
1097 1097  
1098 1098  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
... ... @@ -1135,6 +1135,7 @@
1135 1135  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1136 1136  
1137 1137  
1166 +
1138 1138  = 8. AT Commands Combination =
1139 1139  
1140 1140  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1143,6 +1143,7 @@
1143 1143  * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1144 1144  
1145 1145  
1175 +
1146 1146  == 8.2 Use Downlink Command to set a fix uplink DR ==
1147 1147  
1148 1148  {{info}}

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0