Last modified by kai on 2024/09/06 10:00
<
From version < 38.77 >
edited by Xiaoling
on 2022/05/31 09:18
To version < 21.1 >
edited by Xiaoling
on 2022/05/27 17:53
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -3,7 +3,6 @@
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
... ... @@ -20,10 +20,11 @@
20 20  
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
22 +** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
23 +** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25 25  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26 26  
26 +
27 27  = 3. Support End Node and firmware version =
28 28  
29 29  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
... ... @@ -98,6 +98,7 @@
98 98  )))
99 99  
100 100  
101 +
101 101  = 4. System Management Commands =
102 102  
103 103  == 4.1 Change Uplink Interval ==
... ... @@ -334,6 +334,7 @@
334 334  )))
335 335  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
336 336  
338 +
337 337  == 5.3 Application Session Key ==
338 338  
339 339  Feature: Get or Set the Application Session Key.
... ... @@ -495,6 +495,7 @@
495 495  )))
496 496  
497 497  
500 +
498 498  == 6.4 LoRa® Network Join Mode ==
499 499  
500 500  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
... ... @@ -524,6 +524,7 @@
524 524  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
525 525  
526 526  
530 +
527 527  == 6.5 LoRa® Network Join Status ==
528 528  
529 529  Feature: LoRa® Network Join Status.
... ... @@ -540,6 +540,7 @@
540 540  )))
541 541  
542 542  
547 +
543 543  == 6.6 Print Last Received Data in Raw Format ==
544 544  
545 545  Feature: Print Last Received Data in Raw Format<port:data>.
... ... @@ -556,6 +556,7 @@
556 556  )))
557 557  
558 558  
564 +
559 559  == 6.7 Print Last Received Data in Binary Format ==
560 560  
561 561  Feature: Print Last Received Data in Binary Format<port:data>.
... ... @@ -572,6 +572,7 @@
572 572  )))
573 573  
574 574  
581 +
575 575  == 6.8 Send Text Data ==
576 576  
577 577  Feature: Send Text Data<port:data>.
... ... @@ -592,6 +592,7 @@
592 592  )))
593 593  
594 594  
602 +
595 595  == 6.9 Send Hexadecimal Data ==
596 596  
597 597  Feature: Send hexadecimal data along with the application port.
... ... @@ -611,6 +611,7 @@
611 611  )))
612 612  
613 613  
622 +
614 614  = 7. LoRaWAN network management =
615 615  
616 616  == 7.1 Adaptive Data Rate ==
... ... @@ -643,6 +643,7 @@
643 643  * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
644 644  
645 645  
655 +
646 646  == 7.2 LoRa® Class ==
647 647  
648 648  Feature: Get or Set the Device Class(Currently only support class A, class C).
... ... @@ -662,6 +662,7 @@
662 662  )))
663 663  
664 664  
675 +
665 665  == 7.3 Duty Cycle Setting ==
666 666  
667 667  Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
... ... @@ -681,6 +681,7 @@
681 681  )))
682 682  
683 683  
695 +
684 684  == 7.4 Data Rate ==
685 685  
686 686  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
... ... @@ -710,6 +710,7 @@
710 710  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
711 711  
712 712  
725 +
713 713  == 7.5 Frame Counter Downlink ==
714 714  
715 715  Feature: Get or Set the Frame Counter Downlink.
... ... @@ -731,6 +731,7 @@
731 731  )))
732 732  
733 733  
747 +
734 734  == 7.6 Frame Counter Uplink ==
735 735  
736 736  Feature: Get or Set the Frame Counter Uplink.
... ... @@ -750,6 +750,7 @@
750 750  )))
751 751  
752 752  
767 +
753 753  == 7.7 Join Accept Delay1 ==
754 754  
755 755  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
... ... @@ -769,6 +769,7 @@
769 769  )))
770 770  
771 771  
787 +
772 772  == 7.8 Join Accept Delay2 ==
773 773  
774 774  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
... ... @@ -788,6 +788,7 @@
788 788  )))
789 789  
790 790  
807 +
791 791  == 7.9 Public Network Mode ==
792 792  
793 793  Feature: Get or Set the public network mode. (0: off, 1: on)
... ... @@ -809,6 +809,7 @@
809 809  )))
810 810  
811 811  
829 +
812 812  == 7.10 Receive Delay1 ==
813 813  
814 814  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
... ... @@ -828,6 +828,7 @@
828 828  )))
829 829  
830 830  
849 +
831 831  == 7.11 Receive Delay2 ==
832 832  
833 833  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
... ... @@ -847,6 +847,7 @@
847 847  )))
848 848  
849 849  
869 +
850 850  == 7.12 Rx2 Window Data Rate ==
851 851  
852 852  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
... ... @@ -866,6 +866,7 @@
866 866  )))
867 867  
868 868  
889 +
869 869  == 7.13 Rx2 Window Frequency ==
870 870  
871 871  Feature: Get or Set the Rx2 window frequency
... ... @@ -885,6 +885,7 @@
885 885  )))
886 886  
887 887  
909 +
888 888  == 7.14 Transmit Power ==
889 889  
890 890  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
... ... @@ -911,6 +911,7 @@
911 911  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
912 912  
913 913  
936 +
914 914  == 7.15 RSSI of the Last Received Packet ==
915 915  
916 916  Feature: Get or Set the Rx2 window frequency
... ... @@ -927,6 +927,7 @@
927 927  )))
928 928  
929 929  
953 +
930 930  == 7.16 SNR of the Last Received Packet ==
931 931  
932 932  Feature: Get the SNR of the last received packet
... ... @@ -943,6 +943,7 @@
943 943  )))
944 944  
945 945  
970 +
946 946  == 7.17 Application Port ==
947 947  
948 948  Feature: Get or set the application port.
... ... @@ -971,6 +971,7 @@
971 971  * **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
972 972  
973 973  
999 +
974 974  == 7.18 Single Channel Mode ==
975 975  
976 976  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
... ... @@ -988,6 +988,7 @@
988 988  |(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
989 989  
990 990  
1017 +
991 991  == 7.19 Eight Channel Mode ==
992 992  
993 993  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
... ... @@ -1018,6 +1018,7 @@
1018 1018  * **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
1019 1019  
1020 1020  
1048 +
1021 1021  == 7.20 Get or Set RXwindows1 timeout ==
1022 1022  
1023 1023  Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
... ... @@ -1063,6 +1063,7 @@
1063 1063  |(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
1064 1064  
1065 1065  
1094 +
1066 1066  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1067 1067  
1068 1068  Feature: Get or Set uplinkdwelltime
... ... @@ -1091,6 +1091,7 @@
1091 1091  * **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
1092 1092  
1093 1093  
1123 +
1094 1094  == 7.23 Set Packet Receiving Response Level ==
1095 1095  
1096 1096  Feature: Get or Set packet receiving response level. This feature is used to set compatible with different LoRaWAN servers. If RPL doesn;t match , user will see strange message in the server portal.
... ... @@ -1133,6 +1133,7 @@
1133 1133  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1134 1134  
1135 1135  
1166 +
1136 1136  = 8. AT Commands Combination =
1137 1137  
1138 1138  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1141,6 +1141,7 @@
1141 1141  * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1142 1142  
1143 1143  
1175 +
1144 1144  == 8.2 Use Downlink Command to set a fix uplink DR ==
1145 1145  
1146 1146  {{info}}

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0