Last modified by kai on 2024/09/06 10:00
<
From version < 38.36 >
edited by Xiaoling
on 2022/05/31 09:11
To version < 7.8 >
edited by Xiaoling
on 2022/05/11 11:17
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,9 +1,8 @@
1 - **Contents：**
1 +Contens
2 2  
3 3  {{toc/}}
4 4  
5 5  
6 -
7 7  = 1. Introduction =
8 8  
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
... ... @@ -11,95 +11,34 @@
11 11  * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
12 12  * **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device.
13 13  
14 -(((
15 15  **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.**
16 16  
17 -)))
18 18  
19 19  = 2. How to use AT Commands or Downlink command =
20 20  
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 -** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25 -** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
20 +** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
21 +** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
22 +** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26 26  
27 -
28 28  = 3. Support End Node and firmware version =
29 29  
30 -(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
31 -|=(% colspan="3" style="width: 963px;" %)(((
32 -Dragino STM32 base hardware Firmware / LoRaWAN stack list
33 -)))
34 -|(% style="width:187px" %)(((
35 -**Model**
36 -)))|(% style="width:330px" %)(((
37 -**Description**
38 -)))|(% style="width:445px" %)(((
39 -**Firmware Version <~-~-> Stack Version**
40 -)))
41 -|(% style="width:187px" %)(((
42 -[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],
43 -)))|(% style="width:330px" %)(((
44 -Open Source Generic LoRaWAN Sensor Node
45 -)))|(% style="width:445px" %)(((
46 -(((
47 -LSN50 v1.6.0 <~-~-> DR-LWS-003;
48 -)))
49 -
50 -(((
51 -(((
26 +(% style="background-color:#ffffcc; color:green; width:995.222px" %)
27 +|=(% colspan="3" style="width: 992px;" %)Dragino STM32 base hardware Firmware / LoRaWAN stack list
28 +|(% style="width:187px" %)**Model**|(% style="width:349px" %)**Description**|(% style="width:453px" %)**Firmware Version <~-~-> Stack Version**
29 +|(% style="width:187px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:349px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:453px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;(((
52 52  LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version
53 53  )))
54 -)))
55 -)))
56 -|(% style="width:187px" %)(((
57 -[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],
58 -)))|(% style="width:330px" %)(((
59 -LoRaWAN GPS Tracker
60 -)))|(% style="width:445px" %)(((
61 -(((
62 -LGT92 v1.6.3 <~-~-> DR-LWS-003;
63 -)))
64 -
65 -(((
66 -(((
32 +|(% style="width:187px" %)[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],|(% style="width:349px" %)LoRaWAN GPS Tracker|(% style="width:453px" %)LGT92 v1.6.3 <~-~-> DR-LWS-003;(((
67 67  LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version
68 68  )))
69 -)))
70 -)))
71 -|(% style="width:187px" %)(((
72 -[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],
73 -)))|(% style="width:330px" %)(((
74 -LoRaWAN BLE Indoor Tracker
75 -)))|(% style="width:445px" %)(((
76 -LBT1 v1.0 <~-~-> DR-LWS-005;
77 -)))
78 -|(% style="width:187px" %)(((
79 -[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],
80 -)))|(% style="width:330px" %)(((
81 -LoRaWAN RS485 Modbus Converter
82 -)))|(% style="width:445px" %)(((
83 -RS485-LN v1.3 <~-~-> DR-LWS-005;
84 -)))
85 -|(% style="width:187px" %)(((
86 -[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],
87 -)))|(% style="width:330px" %)(((
88 -LoRaWAN Temperature & Humidity Sensor
89 -)))|(% style="width:445px" %)(((
90 -(((
91 -LHT65 v1.7 <~-~-> DR-LWS-003;
92 -)))
93 -
94 -(((
95 -(((
35 +|(% style="width:187px" %)[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],|(% style="width:349px" %)LoRaWAN BLE Indoor Tracker|(% style="width:453px" %)LBT1 v1.0 <~-~-> DR-LWS-005;
36 +|(% style="width:187px" %)[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],|(% style="width:349px" %)LoRaWAN RS485 Modbus Converter|(% style="width:453px" %)RS485-LN v1.3 <~-~-> DR-LWS-005;
37 +|(% style="width:187px" %)[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],|(% style="width:349px" %)LoRaWAN Temperature & Humidity Sensor|(% style="width:453px" %)LHT65 v1.7 <~-~-> DR-LWS-003;(((
96 96  LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version
97 97  )))
98 -)))
99 -)))
100 100  
101 -
102 -
103 103  = 4. System Management Commands =
104 104  
105 105  == 4.1 Change Uplink Interval ==
... ... @@ -111,7 +111,7 @@
111 111  **AT Command: AT+TDC**
112 112  )))
113 113  
114 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
52 +(% style="background-color:#ffffcc; color:green; width:727.222px" %)
115 115  |=(% colspan="3" style="width: 724px;" %)AT+TDC
116 116  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
117 117  |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000(((
... ... @@ -127,19 +127,13 @@
127 127  **Downlink Command: 0x01**
128 128  {{/info}}
129 129  
130 -(((
131 131  Format: Command Code (0x01) followed by 3 bytes time value.
132 -)))
133 133  
134 -(((
135 135  If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.
136 -)))
137 137  
138 138  * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
139 139  * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140 140  
141 -
142 -
143 143  == 4.2 Reboot End Node ==
144 144  
145 145  Feature: Reboot End Node to perform a new OTAA or ABP Join.
... ... @@ -148,7 +148,7 @@
148 148  **AT Command: ATZ**
149 149  {{/info}}
150 150  
151 -(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
83 +(% border="0" style="background-color:#ffffcc; color:green; width:727.222px" %)
152 152  |=(% colspan="3" %)ATZ: Trig a reset of the MCU
153 153  |**Command Example**|**Function**|**Response**
154 154  |ATZ|Reset MCU|(((
... ... @@ -169,16 +169,10 @@
169 169  **Downlink Command: 0x04**
170 170  {{/info}}
171 171  
172 -(((
173 173  Format: Command Code (0x04) followed by FF.
174 -)))
175 175  
176 -(((
177 177  If the downlink payload=**04FF**, the end node will reboot.
178 178  
179 -
180 -)))
181 -
182 182  == 4.3 Reset to factory Default ==
183 183  
184 184  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
... ... @@ -187,7 +187,7 @@
187 187  **AT Command: AT+FDR**
188 188  {{/info}}
189 189  
190 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
116 +(% style="background-color:#ffffcc; color:green; width:831.222px" %)
191 191  |=(% colspan="3" style="width: 828px;" %)Reset to factory default
192 192  |(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
193 193  |(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)(((
... ... @@ -208,13 +208,9 @@
208 208  **Downlink Command: 0x04**
209 209  {{/info}}
210 210  
211 -(((
212 212  Format: Command Code (0x04) followed by FE.
213 -)))
214 214  
215 -(((
216 216  If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve.
217 -)))
218 218  
219 219  
220 220  == 4.4 Show Firmware Version ==
... ... @@ -225,10 +225,10 @@
225 225  **AT Command: AT+VER**
226 226  {{/info}}
227 227  
228 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
229 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
230 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
231 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)(((
150 +(% style="background-color:#ffffcc; color:green" %)
151 +|=(% colspan="3" %)AT+VER: Image Version and Frequency Band
152 +|**Command Example**|**Function**|**Response**
153 +|AT+VER=?|Show Image version and Frequency Band|(((
232 232  1.3 EU868
233 233  
234 234  OK
... ... @@ -238,25 +238,17 @@
238 238  **Downlink Command: 0x26 (Valid in 006 stack)**
239 239  {{/info}}
240 240  
241 -(((
242 242  Downlink Format: 0x26
243 -)))
244 244  
245 -(((
246 246  Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes
247 -)))
248 248  
249 -(((
250 250  **xx: Software Type:**
251 -)))
252 252  
253 253  * 0x00 01: LGT92 Version
254 254  * 0x00 02: LBT1
255 255  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
256 256  
257 -(((
258 258  **yy: Frequency Band:**
259 -)))
260 260  
261 261  * 0x01: EU868
262 262  * 0x02: US915
... ... @@ -269,9 +269,7 @@
269 269  * 0x09: AS923-2
270 270  * 0xa0: AS923-3
271 271  
272 -(((
273 273  **zz: Subband**
274 -)))
275 275  
276 276  firmware version: v1.1.0 ~-~-> 110
277 277  
... ... @@ -284,7 +284,7 @@
284 284  **AT Command: AT+CFG**
285 285  {{/info}}
286 286  
287 -(% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
199 +(% style="background-color:#ffffcc; color:green; width:599.222px" %)
288 288  |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
289 289  |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
290 290  |(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)(((
... ... @@ -311,7 +311,7 @@
311 311  **AT Command: AT+APPEUI**
312 312  {{/info}}
313 313  
314 -(% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
226 +(% style="background-color:#ffffcc; color:green; width:686.222px" %)
315 315  |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
316 316  |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
317 317  |(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00(((
... ... @@ -327,7 +327,7 @@
327 327  **AT Command: AT+APPKEY**
328 328  {{/info}}
329 329  
330 -(% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
242 +(% style="background-color:#ffffcc; color:green; width:976.222px" %)
331 331  |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
332 332  |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
333 333  |(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35(((
... ... @@ -335,7 +335,6 @@
335 335  )))
336 336  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
337 337  
338 -
339 339  == 5.3 Application Session Key ==
340 340  
341 341  Feature: Get or Set the Application Session Key.
... ... @@ -344,7 +344,7 @@
344 344  **AT Command: AT+APPSKEY**
345 345  {{/info}}
346 346  
347 -(% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
258 +(% style="background-color:#ffffcc; color:green; width:1040.22px" %)
348 348  |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
349 349  |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
350 350  |(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2(((
... ... @@ -354,7 +354,6 @@
354 354  OK
355 355  )))
356 356  
357 -
358 358  == 5.4 Device Address ==
359 359  
360 360  Feature: Get or Set the Device Address.
... ... @@ -363,7 +363,7 @@
363 363  **AT Command: AT+DADDR**
364 364  {{/info}}
365 365  
366 -(% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
276 +(% style="background-color:#ffffcc; color:green; width:795.222px" %)
367 367  |=(% colspan="3" style="width: 792px;" %)AT+DADDR
368 368  |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
369 369  |(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)(((
... ... @@ -373,7 +373,6 @@
373 373  )))
374 374  |(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
375 375  
376 -
377 377  == 5.5 Device EUI ==
378 378  
379 379  Feature: Get or Set the Device EUI.
... ... @@ -382,7 +382,7 @@
382 382  **AT Command: AT+DEUI**
383 383  {{/info}}
384 384  
385 -(% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
294 +(% style="background-color:#ffffcc; color:green; width:1035.22px" %)
386 386  |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
387 387  |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
388 388  |(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55(((
... ... @@ -392,7 +392,6 @@
392 392  OK
393 393  )))
394 394  
395 -
396 396  == 5.6 Network ID ==
397 397  
398 398  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
... ... @@ -401,7 +401,7 @@
401 401  **AT Command: AT+NWKID**
402 402  {{/info}}
403 403  
404 -(% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
312 +(% style="background-color:#ffffcc; color:green; width:448.222px" %)
405 405  |=(% colspan="3" style="width: 445px;" %)AT+NWKID
406 406  |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
407 407  |(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff(((
... ... @@ -409,7 +409,6 @@
409 409  )))
410 410  |(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
411 411  
412 -
413 413  == 5.7 Network Session Key ==
414 414  
415 415  Feature: Get or Set the Network Session Key
... ... @@ -418,7 +418,7 @@
418 418  **AT Command: AT+NWKSKEY**
419 419  {{/info}}
420 420  
421 -(% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
328 +(% style="background-color:#ffffcc; color:green; width:1017.22px" %)
422 422  |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
423 423  |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
424 424  |(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92(((
... ... @@ -426,7 +426,6 @@
426 426  )))
427 427  |(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
428 428  
429 -
430 430  = 6. Joining and sending date on LoRaWAN network =
431 431  
432 432  == 6.1 Confirm Mode ==
... ... @@ -437,7 +437,7 @@
437 437  **AT Command: AT+CFM**
438 438  {{/info}}
439 439  
440 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
346 +(% style="background-color:#ffffcc; color:green; width:710.222px" %)
441 441  |=(% colspan="3" style="width: 707px;" %)AT+CFM
442 442  |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
443 443  |(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0(((
... ... @@ -455,7 +455,6 @@
455 455  * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
456 456  * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
457 457  
458 -
459 459  == 6.2 Confirm Status ==
460 460  
461 461  Feature: Get confirmation status of the last AT+SEND (0-1).
... ... @@ -464,7 +464,7 @@
464 464  **AT Command: AT+CFS**
465 465  {{/info}}
466 466  
467 -(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
372 +(% style="background-color:#ffffcc; color:green; width:534.222px" %)
468 468  |=(% colspan="3" style="width: 531px;" %)AT+CFS
469 469  |(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
470 470  |(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0(((
... ... @@ -471,7 +471,6 @@
471 471  OK
472 472  )))
473 473  
474 -
475 475  == 6.3 Join LoRa® Network ==
476 476  
477 477  Feature: Join network.
... ... @@ -480,7 +480,7 @@
480 480  **AT Command: AT+JOIN**
481 481  {{/info}}
482 482  
483 -(% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
387 +(% style="background-color:#ffffcc; color:green; width:647.222px" %)
484 484  |=(% colspan="3" style="width: 644px;" %)AT+JOIN
485 485  |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
486 486  |(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network(((
... ... @@ -497,7 +497,7 @@
497 497  **AT Command: AT+NJM**
498 498  {{/info}}
499 499  
500 -(% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
404 +(% style="background-color:#ffffcc; color:green; width:753.222px" %)
501 501  |=(% colspan="3" style="width: 750px;" %)AT+NJM
502 502  |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
503 503  |(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1(((
... ... @@ -525,7 +525,7 @@
525 525  **AT Command: AT+NJS**
526 526  {{/info}}
527 527  
528 -(% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
432 +(% style="background-color:#ffffcc; color:green; width:498.222px" %)
529 529  |=(% colspan="3" style="width: 495px;" %)AT+NJS
530 530  |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
531 531  |(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0(((
... ... @@ -540,7 +540,7 @@
540 540  **AT Command: AT+RECV**
541 541  {{/info}}
542 542  
543 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
447 +(% style="background-color:#ffffcc; color:green; width:587.222px" %)
544 544  |=(% colspan="3" style="width: 584px;" %)AT+RECV
545 545  |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
546 546  |(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:(((
... ... @@ -555,7 +555,7 @@
555 555  **AT Command: AT+RECVB**
556 556  {{/info}}
557 557  
558 -(% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
462 +(% style="background-color:#ffffcc; color:green; width:793.222px" %)
559 559  |=(% colspan="3" style="width: 790px;" %)AT+RECVB
560 560  |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
561 561  |(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010(((
... ... @@ -570,7 +570,7 @@
570 570  **AT Command: AT+SEND**
571 571  {{/info}}
572 572  
573 -(% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
477 +(% style="background-color:#ffffcc; color:green; width:991.222px" %)
574 574  |=(% colspan="3" style="width: 988px;" %)AT+SEND
575 575  |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
576 576  |(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK(((
... ... @@ -589,7 +589,7 @@
589 589  **AT Command: AT+SENDB**
590 590  {{/info}}
591 591  
592 -(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
496 +(% style="background-color:#ffffcc; color:green; width:1120.22px" %)
593 593  |=(% colspan="3" style="width: 1117px;" %)AT+SENDB
594 594  |(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
595 595  |(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK
... ... @@ -609,7 +609,7 @@
609 609  **AT Command: AT+ADR**
610 610  {{/info}}
611 611  
612 -(% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
516 +(% style="background-color:#ffffcc; color:green; width:683.222px" %)
613 613  |=(% colspan="3" style="width: 680px;" %)AT+ADR
614 614  |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
615 615  |(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1(((
... ... @@ -638,7 +638,7 @@
638 638  **AT Command:AT+CLASS**
639 639  {{/info}}
640 640  
641 -(% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
545 +(% style="background-color:#ffffcc; color:green; width:507.222px" %)
642 642  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
643 643  |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
644 644  |(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A(((
... ... @@ -656,7 +656,7 @@
656 656  **AT Command:AT+DCS**
657 657  {{/info}}
658 658  
659 -(% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
563 +(% style="background-color:#ffffcc; color:green; width:515.222px" %)
660 660  |=(% colspan="3" style="width: 512px;" %)AT+DCS
661 661  |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
662 662  |(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1(((
... ... @@ -674,7 +674,7 @@
674 674  **AT Command: AT+DR**
675 675  {{/info}}
676 676  
677 -(% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
581 +(% style="background-color:#ffffcc; color:green; width:466.222px" %)
678 678  |=(% colspan="3" style="width: 463px;" %)AT+DR
679 679  |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
680 680  |(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5(((
... ... @@ -702,7 +702,7 @@
702 702  **AT Command:AT+FCD**
703 703  {{/info}}
704 704  
705 -(% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
609 +(% style="background-color:#ffffcc; color:green; width:693.222px" %)
706 706  |=(% colspan="3" style="width: 690px;" %)AT+FCD
707 707  |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
708 708  |(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0(((
... ... @@ -722,7 +722,7 @@
722 722  **AT Command:AT+FCU**
723 723  {{/info}}
724 724  
725 -(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
629 +(% style="background-color:#ffffcc; color:green; width:534.222px" %)
726 726  |=(% colspan="3" style="width: 531px;" %)AT+FCU
727 727  |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
728 728  |(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0(((
... ... @@ -740,7 +740,7 @@
740 740  **AT Command:AT+JN1DL**
741 741  {{/info}}
742 742  
743 -(% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
647 +(% style="background-color:#ffffcc; color:green; width:537.222px" %)
744 744  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
745 745  |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
746 746  |(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000(((
... ... @@ -758,7 +758,7 @@
758 758  **AT Command:AT+JN2DL**
759 759  {{/info}}
760 760  
761 -(% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
665 +(% style="background-color:#ffffcc; color:green; width:538.222px" %)
762 762  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
763 763  |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
764 764  |(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000(((
... ... @@ -776,7 +776,7 @@
776 776  **AT Command:AT+PNM**
777 777  {{/info}}
778 778  
779 -(% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
683 +(% style="background-color:#ffffcc; color:green; width:667.222px" %)
780 780  |=(% colspan="3" style="width: 664px;" %)AT+PNM
781 781  |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
782 782  |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
... ... @@ -796,7 +796,7 @@
796 796  **AT Command:AT+RX1DL**
797 797  {{/info}}
798 798  
799 -(% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
703 +(% style="background-color:#ffffcc; color:green; width:408.222px" %)
800 800  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
801 801  |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
802 802  |(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000(((
... ... @@ -806,21 +806,18 @@
806 806  
807 807  )))
808 808  
809 -== 7.11 Receive Delay2 ==
713 +== 7.11Receive Delay2 ==
810 810  
811 811  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
812 812  
813 -{{info}}
814 -**AT Command:AT+RX2DL**
815 -{{/info}}
717 +AT Command:AT+RX2DL
816 816  
817 -(% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
818 -|=(% colspan="3" style="width: 478px;" %)AT+RX2DL
819 -|(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
820 -|(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000(((
719 +|=(% colspan="3" %)AT+RX2DL
720 +|**Command Example**|**Function**|**Response**
721 +|AT+RX2DL=?|Get the delay.|2000(((
821 821  OK
822 822  )))
823 -|(% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((
724 +|AT+RX2DL=2500|Set the delay.|OK(((
824 824  
825 825  )))
826 826  
... ... @@ -828,17 +828,14 @@
828 828  
829 829  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
830 830  
831 -{{info}}
832 -**AT Command:AT+RX2DR**
833 -{{/info}}
732 +AT Command:AT+RX2DR
834 834  
835 -(% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
836 -|=(% colspan="3" style="width: 522px;" %)AT+RX2DR
837 -|(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
838 -|(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2(((
734 +|=(% colspan="3" %)AT+RX2DR
735 +|**Command Example**|**Function**|**Response**
736 +|AT+RX2DR=?|Get the Rx2 window data rate.|2(((
839 839  OK
840 840  )))
841 -|(% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((
739 +|AT+RX2DR=6|Set the Rx2 window data rate.|OK(((
842 842  
843 843  )))
844 844  
... ... @@ -846,17 +846,14 @@
846 846  
847 847  Feature: Get or Set the Rx2 window frequency
848 848  
849 -{{info}}
850 -**AT Command:AT+RX2FQ**
851 -{{/info}}
747 +AT Command:AT+RX2FQ
852 852  
853 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
854 -|=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
855 -|(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
856 -|(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000(((
749 +|=(% colspan="3" %)AT+RX2FQ
750 +|**Command Example**|**Function**|**Response**
751 +|AT+RX2FQ=?|Get the Rx2 window frequency.|434665000(((
857 857  OK
858 858  )))
859 -|(% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((
754 +|AT+RX2FQ=434665000|Set the Rx2 window frequency.|OK(((
860 860  
861 861  )))
862 862  
... ... @@ -864,17 +864,14 @@
864 864  
865 865  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
866 866  
867 -{{info}}
868 -**AT Command:AT+TXP**
869 -{{/info}}
762 +AT Command:AT+TXP
870 870  
871 -(% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
872 -|=(% colspan="3" style="width: 462px;" %)AT+TXP
873 -|(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
874 -|(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0(((
764 +|=(% colspan="3" %)AT+TXP
765 +|**Command Example**|**Function**|**Response**
766 +|AT+TXP=?|Get the Transmit Power.|0(((
875 875  OK
876 876  )))
877 -|(% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((
769 +|AT+TXP=1|Set the Transmit Power.|OK(((
878 878  
879 879  )))
880 880  
... ... @@ -882,21 +882,18 @@
882 882  
883 883  If the downlink payload=22000100, it means setting the TXP to 0.
884 884  
885 -* **Example 1**: Downlink Payload: **22000102** ~/~/ Set AT+TXP=2.
886 -* **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+TXP=0.
777 +* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2.
778 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0.
887 887  
888 888  == 7.15 RSSI of the Last Received Packet ==
889 889  
890 890  Feature: Get or Set the Rx2 window frequency
891 891  
892 -{{info}}
893 -**AT Command:AT+RSSI**
894 -{{/info}}
784 +AT Command:AT+RSSI
895 895  
896 -(% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
897 -|=(% colspan="3" style="width: 554px;" %)AT+RSSI
898 -|(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
899 -|(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0(((
786 +|=(% colspan="3" %)AT+RSSI
787 +|**Command Example**|**Function**|**Response**
788 +|AT+RSSI=?|Get the RSSI of the last received packet.|0(((
900 900  OK
901 901  )))
902 902  
... ... @@ -904,14 +904,11 @@
904 904  
905 905  Feature: Get the SNR of the last received packet
906 906  
907 -{{info}}
908 -**AT Command:AT+SNR**
909 -{{/info}}
796 +AT Command:AT+SNR
910 910  
911 -(% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
912 -|=(% colspan="3" style="width: 568px;" %)AT+SNR
913 -|(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
914 -|(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0(((
798 +|=(% colspan="3" %)AT+SNR
799 +|**Command Example**|**Function**|**Response**
800 +|AT+SNR=?|Get the RSSI of the last received packet.|0(((
915 915  OK
916 916  )))
917 917  
... ... @@ -919,144 +919,114 @@
919 919  
920 920  Feature: Get or set the application port.
921 921  
922 -{{info}}
923 -**AT Command: AT+PORT**
924 -{{/info}}
808 +AT Command: AT+PORT
925 925  
926 -(% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
927 -|=(% colspan="3" style="width: 497px;" %)AT+PORT
928 -|(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
929 -|(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21(((
810 +|=(% colspan="3" %)AT+PORT
811 +|**Command Example**|**Function**|**Response**
812 +|AT+PORT=?|Get the application port|21(((
930 930  OK
931 931  )))
932 -|(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
815 +|AT+PORT=21|Set the application port|OK
933 933  
934 -{{info}}
935 -**Downlink Command: 0x23**
936 -{{/info}}
817 +Downlink Command: 0x23
937 937  
938 938  Format: Command Code (0x23) followed by 1 bytes port value.
939 939  
940 940  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
941 941  
942 -* **Example 1**: Downlink Payload: **2301** ~/~/ set the application port to 1
943 -* **Example 2**: Downlink Payload:** 2305** ~/~/ set the application port to 5
823 +* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1
824 +* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5
944 944  
945 945  == 7.18 Single Channel Mode ==
946 946  
947 947  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
948 948  
949 -{{info}}
950 -**AT Command: AT+CHS**
951 -{{/info}}
830 +AT Command: AT+CHS
952 952  
953 -(% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
954 -|=(% colspan="3" style="width: 600px;" %)AT+CHS
955 -|(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
956 -|(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0(((
832 +|=(% colspan="3" %)AT+CHS
833 +|**Command Example**|**Function**|**Response**
834 +|AT+CHS=?|Get Frequency for Single Channel Mode|0(((
957 957  OK
958 958  )))
959 -|(% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK
837 +|AT+CHS=868100000|Set Frequency for Single Channel Mode|OK
960 960  
961 961  == 7.19 Eight Channel Mode ==
962 962  
963 963  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
964 964  
965 -{{info}}
966 -**AT Command: AT+CHE**
967 -{{/info}}
843 +AT Command: AT+CHE
968 968  
969 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
970 -|=(% colspan="3" style="width: 707px;" %)AT+CHE
971 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
972 -|(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1(((
845 +|=(% colspan="3" %)AT+CHE
846 +|**Command Example**|**Function**|**Response**
847 +|AT+CHE=?|Get eight channels mode|1(((
973 973  902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7
974 974  
975 975  OK
976 976  )))
977 -|(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
852 +|AT+CHE=1|Set eight channels mode|OK
978 978  
979 -{{info}}
980 -**Downlink Command: 0x24**
981 -{{/info}}
854 +Downlink Command: 0x24
982 982  
983 983  Format: Command Code (0x24) followed by 1 bytes channel value.
984 984  
985 985  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
986 986  
987 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1
988 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5
860 +* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1
861 +* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5
989 989  
990 990  == 7.20 Get or Set RXwindows1 timeout ==
991 991  
992 992  Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
993 993  
994 -{{info}}
995 -**AT Command: AT+RX1WTO**
996 -{{/info}}
867 +AT Command: AT+RX1WTO
997 997  
998 -(% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
999 -|=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1000 -|(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
1001 -|(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14(((
869 +|=(% colspan="3" %)AT+ RX1WTO
870 +|**Command Example**|**Function**|**Response**
871 +|AT+RX1WTO=?|Get RXwindows1 timeout|14(((
1002 1002  OK
1003 1003  )))
1004 -|(% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK
874 +|AT+RX1WTO=60|Set RXwindows1 timeout|OK
1005 1005  
1006 -(((
1007 -**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1008 -)))
876 +AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1009 1009  
1010 -[[image:image-20220526162535-1.png]]
878 +[[~[~[image:https://wiki.dragino.com/images/thumb/5/51/RX1WTO.JPG/600px-RX1WTO.JPG~|~|alt="RX1WTO.JPG" height="239" width="600"~]~]>>url:https://wiki.dragino.com/index.php/File:RX1WTO.JPG]]
1011 1011  
1012 -(((
1013 1013  Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1014 1014  
1015 -
1016 -)))
1017 -
1018 1018  == 7.21 Get or Set RXwindows2 timeout ==
1019 1019  
1020 1020  Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1021 1021  
1022 -{{info}}
1023 -**AT Command: AT+RX2WTO**
1024 -{{/info}}
886 +AT Command: AT+RX2WTO
1025 1025  
1026 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1027 -|=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1028 -|(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
1029 -|(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7(((
888 +|=(% colspan="3" %)AT+ RX2WTO
889 +|**Command Example**|**Function**|**Response**
890 +|AT+RX2WTO=?|Get RXwindows2 timeout|7(((
1030 1030  OK
1031 1031  )))
1032 -|(% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK
893 +|AT+RX2WTO=20|Set RXwindows2 timeout|OK
1033 1033  
1034 1034  == 7.22 Setting up uplinkdwelltime (as923, au915) ==
1035 1035  
1036 1036  Feature: Get or Set uplinkdwelltime
1037 1037  
1038 -{{info}}
1039 -**AT Command: AT+DWELLT**
1040 -{{/info}}
899 +AT Command: AT+DWELLT
1041 1041  
1042 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1043 -|=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1044 -|(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
1045 -|(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1(((
901 +|=(% colspan="3" %)AT+DWELLT
902 +|**Command Example**|**Function**|**Response**
903 +|AT+DWELLT=?|Get uplinkdwelltime|1(((
1046 1046  OK
1047 1047  )))
1048 -|(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
906 +|AT+DWELLT=0|Set uplinkdwelltime|OK
1049 1049  
1050 -{{info}}
1051 -**Downlink Command: 0x25**
1052 -{{/info}}
908 +Downlink Command: 0x25
1053 1053  
1054 1054  Format: Command Code (0x25) followed by 1 bytes state value.
1055 1055  
1056 1056  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
1057 1057  
1058 -* **Example 1**: Downlink Payload: **2501** ~/~/ set uplinkdwelltime to 1
1059 -* **Example 2**: Downlink Payload: **2500** ~/~/ set uplinkdwelltime to 0
914 +* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1
915 +* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0
1060 1060  
1061 1061  == 7.23 Set Packet Receiving Response Level ==
1062 1062  
... ... @@ -1064,11 +1064,11 @@
1064 1064  
1065 1065  RPL value:
1066 1066  
1067 -* **AT+RPL=0:** Device won't immediately reply any downlink commands from platform.
1068 -* **AT+RPL=1:** Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
1069 -* **AT+RPL=2:** Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
1070 -* **AT+RPL=3:** Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
1071 -* **AT+RPL=4: **Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
923 +* AT+RPL=0: Device won't immediately reply any downlink commands from platform.
924 +* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.
925 +* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.
926 +* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.
927 +* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.
1072 1072  
1073 1073  Case Analyes:
1074 1074  
... ... @@ -1076,44 +1076,37 @@
1076 1076  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1077 1077  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1078 1078  
1079 -{{info}}
1080 -**AT Command: AT+RPL**
1081 -{{/info}}
935 +AT Command: AT+RPL
1082 1082  
1083 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1084 -|=(% colspan="3" style="width: 533px;" %)AT+RPL
1085 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1086 -|(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1(((
937 +|=(% colspan="3" %)AT+RPL
938 +|**Command Example**|**Function**|**Response**
939 +|AT+RPL=?|Get packet receiving response level|1(((
1087 1087  OK
1088 1088  )))
1089 -|(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
942 +|AT+RPL=0|Set packet receiving response level|OK
1090 1090  
1091 -{{info}}
1092 -**Downlink Command: 0x21**
1093 -{{/info}}
944 +Downlink Command: 0x21
1094 1094  
1095 1095  Format: Command Code (0x21) followed by 1 bytes level value.
1096 1096  
1097 1097  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
1098 1098  
1099 -* **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1100 -* **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
950 +* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1
951 +* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2
1101 1101  
1102 1102  = 8. AT Commands Combination =
1103 1103  
1104 1104  == 8.1 Set a fix RX2DR for downlink window ==
1105 1105  
1106 -* **AT+ADR=0 **~-~-> Disable ADR first
1107 -* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
957 +* AT+ADR=0 ~-~-> Disable ADR first
958 +* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate
1108 1108  
1109 1109  == 8.2 Use Downlink Command to set a fix uplink DR ==
1110 1110  
1111 -{{info}}
1112 -**Downlink Command: 0x22000500**
1113 -{{/info}}
962 +Downlink Command: 0x22000500
1114 1114  
1115 1115  Same as:
1116 1116  
1117 -* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1118 -* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1119 -* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
966 +* AT+ADR=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Adaptive_Data_Rate]]
967 +* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]]
968 +* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]
image-20220511120050-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -136.3 KB
Content
image-20220526162535-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Xiaoling
Size
... ... @@ -1,1 +1,0 @@
1 -149.4 KB
Content

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0