Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,12 +20,10 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27		-
28		-
29	29	= 3. Support End Node and firmware version =
30	30
31	31	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -99,7 +99,6 @@
99	99	)))
100	100	)))
101	101
102		-
103	103	= 4. System Management Commands =
104	104
105	105	== 4.1 Change Uplink Interval ==
...	...	@@ -138,7 +138,6 @@
138	138	* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
139	139	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140	140
141		-
142	142	== 4.2 Reboot End Node ==
143	143
144	144	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -174,8 +174,6 @@
174	174
175	175	(((
176	176	If the downlink payload=**04FF**, the end node will reboot.
177		-
178		-
179	179	)))
180	180
181	181	== 4.3 Reset to factory Default ==
...	...	@@ -797,7 +797,7 @@
797	797
798	798	)))
799	799
800		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
801	801
802	802	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
803	803
...	...	@@ -998,12 +998,10 @@
998	998	**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
999	999	)))
1000	1000
1001		-[[image:image-20220526162535-1.png]]
	994	+[[image:image-20220511120050-1.png]]
1002	1002
1003	1003	(((
1004	1004	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1005		-
1006		-
1007	1007	)))
1008	1008
1009	1009	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1105,6 +1105,6 @@
1105	1105
1106	1106	Same as:
1107	1107
1108		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1109		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1110		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1099	+* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.1AdaptiveDataRate]]
	1100	+* AT+DR=5 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
	1101	+* AT+TXP=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]