Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,8 +20,8 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
	22	+** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25	25	** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26	26
27	27
...	...	@@ -139,6 +139,7 @@
139	139	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140	140
141	141
	141	+
142	142	== 4.2 Reboot End Node ==
143	143
144	144	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -301,6 +301,7 @@
301	301	)))
302	302
303	303
	304	+
304	304	= 5. Keys, IDs and EUIs management =
305	305
306	306	== 5.1 Application EUI ==
...	...	@@ -320,6 +320,7 @@
320	320	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
321	321
322	322
	324	+
323	323	== 5.2 Application Key ==
324	324
325	325	Feature: Get or Set the Application Key.
...	...	@@ -356,8 +356,6 @@
356	356	OK
357	357	)))
358	358
359		-
360		-
361	361	== 5.4 Device Address ==
362	362
363	363	Feature: Get or Set the Device Address.
...	...	@@ -376,8 +376,6 @@
376	376	)))
377	377	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
378	378
379		-
380		-
381	381	== 5.5 Device EUI ==
382	382
383	383	Feature: Get or Set the Device EUI.
...	...	@@ -396,8 +396,6 @@
396	396	OK
397	397	)))
398	398
399		-
400		-
401	401	== 5.6 Network ID ==
402	402
403	403	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -807,7 +807,7 @@
807	807
808	808	)))
809	809
810		-== 7.11 Receive Delay2 ==
	806	+== 7.11Receive Delay2 ==
811	811
812	812	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
813	813
...	...	@@ -1012,8 +1012,6 @@
1012	1012
1013	1013	(((
1014	1014	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1015		-
1016		-
1017	1017	)))
1018	1018
1019	1019	== 7.21 Get or Set RXwindows2 timeout ==