Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,8 +20,8 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
	22	+** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25	25	** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26	26
27	27
...	...	@@ -139,6 +139,7 @@
139	139	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140	140
141	141
	141	+
142	142	== 4.2 Reboot End Node ==
143	143
144	144	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -301,6 +301,7 @@
301	301	)))
302	302
303	303
	304	+
304	304	= 5. Keys, IDs and EUIs management =
305	305
306	306	== 5.1 Application EUI ==
...	...	@@ -320,6 +320,7 @@
320	320	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
321	321
322	322
	324	+
323	323	== 5.2 Application Key ==
324	324
325	325	Feature: Get or Set the Application Key.
...	...	@@ -356,8 +356,6 @@
356	356	OK
357	357	)))
358	358
359		-
360		-
361	361	== 5.4 Device Address ==
362	362
363	363	Feature: Get or Set the Device Address.
...	...	@@ -803,7 +803,7 @@
803	803
804	804	)))
805	805
806		-== 7.11 Receive Delay2 ==
	806	+== 7.11Receive Delay2 ==
807	807
808	808	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
809	809
...	...	@@ -1008,8 +1008,6 @@
1008	1008
1009	1009	(((
1010	1010	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1011		-
1012		-
1013	1013	)))
1014	1014
1015	1015	== 7.21 Get or Set RXwindows2 timeout ==