Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25		-** See use note for more serves [[Servers Note>>WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -170,8 +170,6 @@
170	170
171	171	(((
172	172	If the downlink payload=**04FF**, the end node will reboot.
173		-
174		-
175	175	)))
176	176
177	177	== 4.3 Reset to factory Default ==
...	...	@@ -793,7 +793,7 @@
793	793
794	794	)))
795	795
796		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
797	797
798	798	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
799	799
...	...	@@ -998,8 +998,6 @@
998	998
999	999	(((
1000	1000	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1001		-
1002		-
1003	1003	)))
1004	1004
1005	1005	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1093,6 +1093,7 @@
1093	1093	* **AT+ADR=0 **~-~-> Disable ADR first
1094	1094	* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1095	1095
	1091	+
1096	1096	== 8.2 Use Downlink Command to set a fix uplink DR ==
1097	1097
1098	1098	{{info}}
...	...	@@ -1101,6 +1101,6 @@
1101	1101
1102	1102	Same as:
1103	1103
1104		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1105		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1106		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1100	+* AT+ADR=0 [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
	1101	+* AT+DR=5 [[Reference>>||anchor="H7.4DataRate"]]
	1102	+* AT+TXP=0 [[Reference>>||anchor="H7.14TransmitPower"]]