Changes for page End Device AT Commands and Downlink Command
Last modified by kai on 2024/09/06 10:00
Summary
-
Page properties (1 modified, 0 added, 0 removed)
-
Attachments (0 modified, 0 added, 2 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,9 +1,8 @@ 1 - **Contents：**1 +Contens 2 2 3 3 {{toc/}} 4 4 5 5 6 - 7 7 = 1. Introduction = 8 8 9 9 Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands: ... ... @@ -11,95 +11,62 @@ 11 11 * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device. 12 12 * **Sensor Related Commands:** Only for special sensor, such as control relay, poll RS485 device. 13 13 14 -((( 15 15 **This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.** 16 16 17 -))) 18 18 19 19 = 2. How to use AT Commands or Downlink command = 20 20 21 21 * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]] 22 22 * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command: 23 -** Use HEX format to send a downlink: [[TTN v3>>doc :Main.Notes.WebHome]]24 -** Use Base64 format to send a downlink: [[Chirpstack>>doc :Main.Notes.WebHome]].25 -** See use note for more serves [[Servers Note>>doc :Main.WebHome]](IoT LoRaWANServer)20 +** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]] 21 +** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]]. 22 +** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]] 26 26 27 - 28 28 = 3. Support End Node and firmware version = 29 29 30 -(% border="1" style="background-color:#ffffcc; color:green; width:966px" %) 31 -|=(% colspan="3" style="width: 963px;" %)((( 32 -Dragino STM32 base hardware Firmware / LoRaWAN stack list 33 -))) 34 -|(% style="width:187px" %)((( 35 -**Model** 36 -)))|(% style="width:330px" %)((( 37 -**Description** 38 -)))|(% style="width:445px" %)((( 39 -**Firmware Version <~-~-> Stack Version** 40 -))) 41 -|(% style="width:187px" %)((( 42 -[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]], 43 -)))|(% style="width:330px" %)((( 44 -Open Source Generic LoRaWAN Sensor Node 45 -)))|(% style="width:445px" %)((( 46 -((( 47 -LSN50 v1.6.0 <~-~-> DR-LWS-003; 48 -))) 49 49 50 -((( 51 -((( 27 +|=(% colspan="3" %)PWR LED4G control (Second +3.3v)USB POWER(+5v) Control 28 +|=PWR LED|=4G control (Second +3.3v)|=USB POWER(+5v) Control 29 +|((( 30 + 31 + 32 ++3.3v 33 +)))|((( 34 + 35 + 36 +GPIO15 37 +)))| 38 +|+3.3v|GPIO15 |GPIO1 39 +|+3.3v|GPIO15 |GPIO1 40 +|+3.3v| | 41 +|+3.3v|PA17| 42 + 43 +(% style="background-color:#ffffcc; color:green; width:1039.22px" %) 44 +|(% colspan="3" style="width:1036px" %)** Dragino STM32 base hardware Firmware / LoRaWAN stack list** 45 +|(% style="width:216px" %)**Model**|(% style="width:346px" %)**Description**|(% style="width:472px" %)**Firmware Version <~-~-> Stack Version** 46 +|(% style="width:216px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:346px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:472px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;((( 52 52 LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version 53 53 ))) 54 -))) 55 -))) 56 -|(% style="width:187px" %)((( 57 -[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]], 58 -)))|(% style="width:330px" %)((( 59 -LoRaWAN GPS Tracker 60 -)))|(% style="width:445px" %)((( 61 -((( 62 -LGT92 v1.6.3 <~-~-> DR-LWS-003; 63 -))) 49 +|(% style="width:216px" %) |(% style="width:346px" %) |(% style="width:472px" %) 50 +|(% style="width:216px" %) |(% style="width:346px" %) |(% style="width:472px" %) 51 +|(% style="width:216px" %) |(% style="width:346px" %) |(% style="width:472px" %) 52 +|(% style="width:216px" %) |(% style="width:346px" %) |(% style="width:472px" %) 64 64 65 -((( 66 -((( 54 +(% border="1" style="background-color:#ffffcc; color:green; width:942.222px" %) 55 +|=(% colspan="3" style="width: 939px;" %) Dragino STM32 base hardware Firmware / LoRaWAN stack list 56 +|(% style="width:187px" %)**Model**|(% style="width:306px" %)**Description**|(% style="width:443px" %)**Firmware Version <~-~-> Stack Version** 57 +|(% style="width:187px" %)[[LSN50-v1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/128-lsn50.html]], [[LSN50-V2>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/155-lsn50-v2.html]],|(% style="width:306px" %)Open Source Generic LoRaWAN Sensor Node|(% style="width:443px" %)LSN50 v1.6.0 <~-~-> DR-LWS-003;((( 58 +LSN50 v1.7.0 <~-~-> DR-LWS-005; ~-~-> Support since this version 59 +))) 60 +|(% style="width:187px" %)[[LGT92>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/142-lgt-92.html]],|(% style="width:306px" %)LoRaWAN GPS Tracker|(% style="width:443px" %)LGT92 v1.6.3 <~-~-> DR-LWS-003;((( 67 67 LGT92 v1.6.4 <~-~-> DR-LWS-005;~-~-> Support since this version 68 68 ))) 69 -))) 70 -))) 71 -|(% style="width:187px" %)((( 72 -[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]], 73 -)))|(% style="width:330px" %)((( 74 -LoRaWAN BLE Indoor Tracker 75 -)))|(% style="width:445px" %)((( 76 -LBT1 v1.0 <~-~-> DR-LWS-005; 77 -))) 78 -|(% style="width:187px" %)((( 79 -[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]], 80 -)))|(% style="width:330px" %)((( 81 -LoRaWAN RS485 Modbus Converter 82 -)))|(% style="width:445px" %)((( 83 -RS485-LN v1.3 <~-~-> DR-LWS-005; 84 -))) 85 -|(% style="width:187px" %)((( 86 -[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]], 87 -)))|(% style="width:330px" %)((( 88 -LoRaWAN Temperature & Humidity Sensor 89 -)))|(% style="width:445px" %)((( 90 -((( 91 -LHT65 v1.7 <~-~-> DR-LWS-003; 92 -))) 93 - 94 -((( 95 -((( 63 +|(% style="width:187px" %)[[LBT1>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/165-lbt1.html]],|(% style="width:306px" %)LoRaWAN BLE Indoor Tracker|(% style="width:443px" %)LBT1 v1.0 <~-~-> DR-LWS-005; 64 +|(% style="width:187px" %)[[RS485-LN>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/154-rs485-ln.html]],|(% style="width:306px" %)LoRaWAN RS485 Modbus Converter|(% style="width:443px" %)RS485-LN v1.3 <~-~-> DR-LWS-005; 65 +|(% style="width:187px" %)[[LHT65>>url:http://www.dragino.com/products/lora-lorawan-end-node/item/151-lht65.html]],|(% style="width:306px" %)LoRaWAN Temperature & Humidity Sensor|(% style="width:443px" %)LHT65 v1.7 <~-~-> DR-LWS-003;((( 96 96 LHT65 v1.8.0 <~-~-> DR-LWS-005;~-~-> Support since this version 97 97 ))) 98 -))) 99 -))) 100 100 101 - 102 - 103 103 = 4. System Management Commands = 104 104 105 105 == 4.1 Change Uplink Interval == ... ... @@ -108,11 +108,11 @@ 108 108 109 109 (% class="box infomessage" %) 110 110 ((( 111 - **AT Command: AT+TDC**77 +AT Command: AT+TDC 112 112 ))) 113 113 114 114 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %) 115 -|=(% colspan="3" style="width: 724px;" %)AT+TDC 81 +|=(% colspan="3" style="width: 724px;" %) AT+TDC 116 116 |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response** 117 117 |(% style="width:165px" %)AT+TDC=?|(% style="width:227px" %)Show current transmit Interval|(% style="width:329px" %)30000((( 118 118 OK ... ... @@ -123,34 +123,27 @@ 123 123 Set transmit interval to 60000ms = 60 seconds 124 124 ))) 125 125 126 -{{info}} 127 127 **Downlink Command: 0x01** 128 -{{/info}} 129 129 130 -((( 131 131 Format: Command Code (0x01) followed by 3 bytes time value. 132 -))) 133 133 134 -((( 135 135 If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01. 136 -))) 137 137 138 138 * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds 139 139 * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds 140 140 141 - 142 - 143 143 == 4.2 Reboot End Node == 144 144 145 145 Feature: Reboot End Node to perform a new OTAA or ABP Join. 146 146 147 147 {{info}} 148 - **AT Command: ATZ**106 +AT Command: ATZ 149 149 {{/info}} 150 150 151 151 (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %) 152 -|=(% colspan="3" %)ATZ: Trig a reset of the MCU 110 +|=(% colspan="3" %) ATZ: Trig a reset of the MCU 153 153 |**Command Example**|**Function**|**Response** 112 +~)~)~) 154 154 |ATZ|Reset MCU|((( 155 155 Device reset and show booting info 156 156 ... ... @@ -165,56 +165,35 @@ 165 165 <followed by the Tx and Rx information> 166 166 ))) 167 167 168 -{{info}} 169 -**Downlink Command: 0x04** 170 -{{/info}} 127 +Downlink Command: 0x04 171 171 172 -((( 173 173 Format: Command Code (0x04) followed by FF. 174 -))) 175 175 176 -((( 177 -If the downlink payload=**04FF**, the end node will reboot. 131 +If the downlink payload=04FF, the end node will reboot. 178 178 179 - 180 -))) 181 - 182 182 == 4.3 Reset to factory Default == 183 183 184 184 Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command. 185 185 186 -{{info}} 187 -**AT Command: AT+FDR** 188 -{{/info}} 137 +AT Command: AT+FDR 189 189 190 -(% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %) 191 -|=(% colspan="3" style="width: 828px;" %)Reset to factory default 192 -|(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response** 193 -|(% style="width:181px" %)AT+FDR|(% style="width:181px" %)Reset to factory default|(% style="width:465px" %)((( 194 -Device reset to factory default parameters and show booting info 139 +|=(% colspan="3" %)Reset to factory default 140 +|**Command Example**|**Function**|**Response** 141 +|AT+FDR|Reset to factory default|Device reset to factory default parameters and show booting info 195 195 196 -LSN50 Device/LoRa ST Module 197 - 143 +{{{LSN50 Device/LoRa ST Module 198 198 Image Version: XX 199 - 200 200 Frequency Band: XX 201 - 202 202 DevEui= XX XX XX XX XX XX XX XX 203 - 204 204 Please set the parameters or reset Device to apply change 205 - )))148 +}}} 206 206 207 -{{info}} 208 -**Downlink Command: 0x04** 209 -{{/info}} 210 210 211 -((( 151 +Downlink Command: 0x04 152 + 212 212 Format: Command Code (0x04) followed by FE. 213 -))) 214 214 215 -((( 216 -If the downlink payload=**04FE**, Reset Parameters to Factory Default, Keys Reserve. 217 -))) 155 +If the downlink payload=04FE, Reset Parameters to Factory Default, Keys Reserve. 218 218 219 219 220 220 == 4.4 Show Firmware Version == ... ... @@ -221,42 +221,30 @@ 221 221 222 222 Feature: Show firmware version. No downlink command yet. 223 223 224 -{{info}} 225 -**AT Command: AT+VER** 226 -{{/info}} 162 +AT Command: AT+VER 227 227 228 -(% border="1" style="background-color:#ffffcc; color:green; width:586px" %) 229 -|=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band 230 -|(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response** 231 -|(% style="width:170px" %)AT+VER=?|(% style="width:300px" %)Show Image version and Frequency Band|(% style="width:113px" %)((( 232 -1.3 EU868 164 +|=(% colspan="3" %)AT+VER: Image Version and Frequency Band 165 +|**Command Example**|**Function**|**Response** 166 +|AT+VER=?|Show Image version and Frequency Band| 233 233 168 +{{{1.3 EU868 234 234 OK 235 - )))170 +}}} 236 236 237 -{{info}} 238 -**Downlink Command: 0x26 (Valid in 006 stack)** 239 -{{/info}} 240 240 241 -((( 173 +Downlink Command: 0x26 (Valid in 006 stack) 174 + 242 242 Downlink Format: 0x26 243 -))) 244 244 245 -((( 246 246 Device will reply with firmware version info, device info. frequency band info. detail please check device user manual. Total 5 bytes Example: If device is of firmware version 1.1.0 Upload: xx ~-~- yy ~-~- zz ~-~- 110 total 5 bytes 247 -))) 248 248 249 -((( 250 -**xx: Software Type:** 251 -))) 179 +xx: Software Type: 252 252 253 253 * 0x00 01: LGT92 Version 254 254 * 0x00 02: LBT1 255 255 * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01 256 256 257 -((( 258 -**yy: Frequency Band:** 259 -))) 185 +yy: Frequency Band: 260 260 261 261 * 0x01: EU868 262 262 * 0x02: US915 ... ... @@ -269,9 +269,7 @@ 269 269 * 0x09: AS923-2 270 270 * 0xa0: AS923-3 271 271 272 -((( 273 -**zz: Subband** 274 -))) 198 +zz: Subband 275 275 276 276 firmware version: v1.1.0 ~-~-> 110 277 277 ... ... @@ -280,27 +280,21 @@ 280 280 281 281 Feature: Show All configure. No downlink command yet. 282 282 283 -{{info}} 284 -**AT Command: AT+CFG** 285 -{{/info}} 207 +AT Command: AT+CFG 286 286 287 -(% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %) 288 -|=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations 289 -|(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response** 290 -|(% style="width:160px" %)AT+CFG|(% style="width:154px" %)Show all configures|(% style="width:280px" %)((( 291 -AT+DEUI = XX XX XX XX XX XX XX XX 209 +|=(% colspan="3" %)AT+CFG: Print all configurations 210 +|**Command Example**|**Function**|**Response** 211 +|AT+CFG|Show all configures| 292 292 213 +{{{AT+DEUI = XX XX XX XX XX XX XX XX 293 293 AT+DADDR=XXXXXXXX 294 - 295 295 ………. 296 - 297 297 AT+RX2WTO=X 298 - 299 299 AT+CHS=868100000 300 - 301 301 OK 302 - )))219 +}}} 303 303 221 + 304 304 = 5. Keys, IDs and EUIs management = 305 305 306 306 == 5.1 Application EUI == ... ... @@ -307,49 +307,40 @@ 307 307 308 308 Feature: Get or Set the Application EUI. 309 309 310 -{{info}} 311 -**AT Command: AT+APPEUI** 312 -{{/info}} 228 +AT Command: AT+APPEUI 313 313 314 -(% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %) 315 -|=(% colspan="3" style="width: 683px;" %)AT+APPEUI 316 -|(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response** 317 -|(% style="width:305px" %)AT+APPEUI=?|(% style="width:186px" %)Get the Application EUI|(% style="width:191px" %)00 b3 d5 00 00 00 00 00((( 230 +|=(% colspan="3" %)AT+APPEUI 231 +|**Command Example**|**Function**|**Response** 232 +|AT+APPEUI=?|Get the Application EUI|00 b3 d5 00 00 00 00 00((( 318 318 OK 319 319 ))) 320 -| (% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK235 +|AT+APPEUI=00 b3 d5 7e f0 00 4d 34|Set the Application EUI|OK 321 321 322 322 == 5.2 Application Key == 323 323 324 324 Feature: Get or Set the Application Key. 325 325 326 -{{info}} 327 -**AT Command: AT+APPKEY** 328 -{{/info}} 241 +AT Command: AT+APPKEY 329 329 330 -(% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %) 331 -|=(% colspan="3" style="width: 973px;" %)AT+APPKEY 332 -|(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response** 333 -|(% style="width:441px" %)AT+APPKEY=?|(% style="width:180px" %)Get the Application Key|(% style="width:350px" %)00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35((( 243 +|=(% colspan="3" %)AT+APPKEY 244 +|**Command Example**|**Function**|**Response** 245 +|AT+APPKEY=?|Get the Application Key|00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35((( 334 334 OK 335 335 ))) 336 -| (% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK248 +|AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|Set the Application Key.|OK 337 337 338 338 == 5.3 Application Session Key == 339 339 340 340 Feature: Get or Set the Application Session Key. 341 341 342 -{{info}} 343 -**AT Command: AT+APPSKEY** 344 -{{/info}} 254 +AT Command: AT+APPSKEY 345 345 346 -(% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %) 347 -|=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY 348 -|(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response** 349 -|(% style="width:451px" %)AT+APPSKEY=?|(% style="width:231px" %)Get the Application Session Key|(% style="width:354px" %)00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2((( 256 +|=(% colspan="3" %)AT+APPSKEY 257 +|**Command Example**|**Function**|**Response** 258 +|AT+APPSKEY=?|Get the Application Session Key|00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2((( 350 350 OK 351 351 ))) 352 -| (% style="width:451px" %)AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|(% style="width:231px" %)Set the Application Session Key|(% style="width:354px" %)(While Error in format, return AT_PARAM_ERROR)(((261 +|AT+APPSKEY=00 7d dc 73 33 d3 eb 9e 14 38 d5 a4 3e 62 5b e2|Set the Application Session Key.|(While Error in format, return AT_PARAM_ERROR)((( 353 353 OK 354 354 ))) 355 355 ... ... @@ -357,35 +357,29 @@ 357 357 358 358 Feature: Get or Set the Device Address. 359 359 360 -{{info}} 361 -**AT Command: AT+DADDR** 362 -{{/info}} 269 +AT Command: AT+DADDR 363 363 364 -(% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %) 365 -|=(% colspan="3" style="width: 792px;" %)AT+DADDR 366 -|(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response** 367 -|(% style="width:192px" %)AT+DADDR=?|(% style="width:241px" %)Get the Application Session Key.|(% style="width:359px" %)(While Error in format, return AT_PARAM_ERROR)((( 271 +|=(% colspan="3" %)AT+DADDR 272 +|**Command Example**|**Function**|**Response** 273 +|AT+DADDR=?|Get the Application Session Key.|(While Error in format, return AT_PARAM_ERROR)((( 368 368 A8 40 41 FF 369 369 370 370 OK 371 371 ))) 372 -| (% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK278 +|AT+DADDR=A8 40 41 FF|Set the Application Session Key.|OK 373 373 374 374 == 5.5 Device EUI == 375 375 376 376 Feature: Get or Set the Device EUI. 377 377 378 -{{info}} 379 -**AT Command: AT+DEUI** 380 -{{/info}} 284 +AT Command: AT+DEUI 381 381 382 -(% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %) 383 -|=(% colspan="3" style="width: 1032px;" %)AT+DEUI 384 -|(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response** 385 -|(% style="width:250px" %)AT+DEUI=?|(% style="width:147px" %)Get the Device EUI.|(% style="width:634px" %)00 44 34 22 33 45 55 55((( 286 +|=(% colspan="3" %)AT+DEUI 287 +|**Command Example**|**Function**|**Response** 288 +|AT+DEUI=?|Get the Device EUI.|00 44 34 22 33 45 55 55((( 386 386 OK 387 387 ))) 388 -| (% style="width:250px" %)AT+DEUI=A8 40 41 FF FF 12 34 56|(% style="width:147px" %)Set the Device EUI.|(% style="width:634px" %)(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)(((291 +|AT+DEUI=A8 40 41 FF FF 12 34 56|Set the Device EUI.|(System will write new value to Device EUI,While Error in format, return AT_PARAM_ERROR)((( 389 389 OK 390 390 ))) 391 391 ... ... @@ -393,33 +393,27 @@ 393 393 394 394 Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection) 395 395 396 -{{info}} 397 -**AT Command: AT+NWKID** 398 -{{/info}} 299 +AT Command: AT+NWKID 399 399 400 -(% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %) 401 -|=(% colspan="3" style="width: 445px;" %)AT+NWKID 402 -|(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response** 403 -|(% style="width:191px" %)AT+NWKID=?|(% style="width:153px" %)Get the Network ID.|(% style="width:101px" %)a8 40 41 ff((( 301 +|=(% colspan="3" %)AT+NWKID 302 +|**Command Example**|**Function**|**Response** 303 +|AT+NWKID=?|Get the Network ID.|a8 40 41 ff((( 404 404 OK 405 405 ))) 406 -| (% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK306 +|AT+NWKID=A8 40 41 FF|Set the Network ID.|OK 407 407 408 408 == 5.7 Network Session Key == 409 409 410 410 Feature: Get or Set the Network Session Key 411 411 412 -{{info}} 413 -**AT Command: AT+NWKSKEY** 414 -{{/info}} 312 +AT Command: AT+NWKSKEY 415 415 416 -(% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %) 417 -|=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY 418 -|(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response** 419 -|(% style="width:455px" %)AT+NWKSKEY=?|(% style="width:215px" %)Get the Network Session Key.|(% style="width:343px" %)00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92((( 314 +|=(% colspan="3" %)AT+NWKSKEY 315 +|**Command Example**|**Function**|**Response** 316 +|AT+NWKSKEY=?|Get the Network Session Key.|00 4f 19 25 52 ce 97 09 d7 fa 84 71 db 51 02 92((( 420 420 OK 421 421 ))) 422 -| (% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK319 +|AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|Set the Network Session Key.|OK 423 423 424 424 = 6. Joining and sending date on LoRaWAN network = 425 425 ... ... @@ -427,18 +427,15 @@ 427 427 428 428 Feature: Get or Set the confirmation mode (0-1). 429 429 430 -{{info}} 431 -**AT Command: AT+CFM** 432 -{{/info}} 327 +AT Command: AT+CFM 433 433 434 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %) 435 -|=(% colspan="3" style="width: 707px;" %)AT+CFM 436 -|(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response** 437 -|(% style="width:155px" %)AT+CFM=?|(% style="width:205px" %)Get the confirmation mode|(% style="width:346px" %)0((( 329 +|=(% colspan="3" %)AT+CFM 330 +|**Command Example**|**Function**|**Response** 331 +|AT+CFM=?|Get the confirmation mode|0((( 438 438 OK 439 439 ))) 440 -| (% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK441 -| (% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR334 +|AT+CFM=1|Set the confirmation mode|OK 335 +|AT+CFM=2|Set the confirmation mode|While Error in format, return AT_PARAM_ERROR 442 442 443 443 Downlink Command: 0x05 444 444 ... ... @@ -453,14 +453,11 @@ 453 453 454 454 Feature: Get confirmation status of the last AT+SEND (0-1). 455 455 456 -{{info}} 457 -**AT Command: AT+CFS** 458 -{{/info}} 350 +AT Command: AT+CFS 459 459 460 -(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %) 461 -|=(% colspan="3" style="width: 531px;" %)AT+CFS 462 -|(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response** 463 -|(% style="width:156px" %)AT+CFS=?|(% style="width:193px" %)Get confirmation status|(% style="width:178px" %)0((( 352 +|=(% colspan="3" %)AT+CFS 353 +|**Command Example**|**Function**|**Response** 354 +|AT+CFS=?|Get confirmation status|0((( 464 464 OK 465 465 ))) 466 466 ... ... @@ -468,14 +468,11 @@ 468 468 469 469 Feature: Join network. 470 470 471 -{{info}} 472 -**AT Command: AT+JOIN** 473 -{{/info}} 362 +AT Command: AT+JOIN 474 474 475 -(% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %) 476 -|=(% colspan="3" style="width: 644px;" %)AT+JOIN 477 -|(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response** 478 -|(% style="width:163px" %)AT+JOIN ?|(% style="width:147px" %)Get imformation.|(% style="width:334px" %)AT+JOIN: Join network((( 364 +|=(% colspan="3" %)AT+JOIN 365 +|**Command Example**|**Function**|**Response** 366 +|AT+JOIN ?|Get imformation.|AT+JOIN: Join network((( 479 479 OK 480 480 481 481 While Error in format, return AT_BUSY_ERROR ... ... @@ -485,42 +485,34 @@ 485 485 486 486 Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA). 487 487 488 -{{info}} 489 -**AT Command: AT+NJM** 490 -{{/info}} 376 +AT Command: AT+NJM 491 491 492 -(% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %) 493 -|=(% colspan="3" style="width: 750px;" %)AT+NJM 494 -|(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response** 495 -|(% style="width:162px" %)AT+NJM=?|(% style="width:227px" %)Get the Network Join Mode|(% style="width:361px" %)1((( 378 +|=(% colspan="3" %)AT+NJM 379 +|**Command Example**|**Function**|**Response** 380 +|AT+NJM=?|Get the Network Join Mode|1((( 496 496 OK 497 497 ))) 498 -| (% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK499 -| (% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR383 +|AT+NJM=0|Set the Network Join Mode|OK 384 +|AT+NJM=2|Set the Network Join Mode|While Error in format, return AT_PARAM_ERROR 500 500 501 -{{info}} 502 -**Downlink Command: 0x20** 503 -{{/info}} 386 +Downlink Command: 0x20 504 504 505 505 Format: Command Code (0x20) followed by 1 bytes mode value. 506 506 507 507 If the downlink payload=2000, it means set the Network Join Mode, while type code is 20. 508 508 509 -* **Example 1:**Downlink Payload:**2000**~/~/ Set AT+NJM=O510 -* **Example 2:**Downlink Payload:**2001**~/~/ Set AT+NJM=1392 +* Example 1: Downlink Payload: 2000 ~/~/ Set AT+NJM=O 393 +* Example 2: Downlink Payload: 2001 ~/~/ Set AT+NJM=1 511 511 512 512 == 6.5 LoRa® Network Join Status == 513 513 514 514 Feature: LoRa® Network Join Status. 515 515 516 -{{info}} 517 -**AT Command: AT+NJS** 518 -{{/info}} 399 +AT Command: AT+NJS 519 519 520 -(% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %) 521 -|=(% colspan="3" style="width: 495px;" %)AT+NJS 522 -|(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response** 523 -|(% style="width:169px" %)AT+NJS=?|(% style="width:164px" %)Get the join status.|(% style="width:161px" %)0((( 401 +|=(% colspan="3" %)AT+NJS 402 +|**Command Example**|**Function**|**Response** 403 +|AT+NJS=?|Get the join status.|0((( 524 524 OK 525 525 ))) 526 526 ... ... @@ -528,14 +528,11 @@ 528 528 529 529 Feature: Print Last Received Data in Raw Format<port:data>. 530 530 531 -{{info}} 532 -**AT Command: AT+RECV** 533 -{{/info}} 411 +AT Command: AT+RECV 534 534 535 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %) 536 -|=(% colspan="3" style="width: 584px;" %)AT+RECV 537 -|(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response** 538 -|(% style="width:161px" %)AT+RECV=?|(% style="width:272px" %)print last received data in raw format.|(% style="width:150px" %)0:((( 413 +|=(% colspan="3" %)AT+RECV 414 +|**Command Example**|**Function**|**Response** 415 +|AT+RECV=?|print last received data in raw format.|0:((( 539 539 OK 540 540 ))) 541 541 ... ... @@ -543,14 +543,11 @@ 543 543 544 544 Feature: Print Last Received Data in Binary Format<port:data>. 545 545 546 -{{info}} 547 -**AT Command: AT+RECVB** 548 -{{/info}} 423 +AT Command: AT+RECVB 549 549 550 -(% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %) 551 -|=(% colspan="3" style="width: 790px;" %)AT+RECVB 552 -|(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response** 553 -|(% style="width:173px" %)AT+RECVB=?|(% style="width:497px" %)print last received data in binary format (with hexadecimal values).|(% style="width:120px" %)2: 0010((( 425 +|=(% colspan="3" %)AT+RECVB 426 +|**Command Example**|**Function**|**Response** 427 +|AT+RECVB=?|print last received data in binary format (with hexadecimal values).|2: 0010((( 554 554 OK 555 555 ))) 556 556 ... ... @@ -558,14 +558,11 @@ 558 558 559 559 Feature: Send Text Data<port:data>. 560 560 561 -{{info}} 562 -**AT Command: AT+SEND** 563 -{{/info}} 435 +AT Command: AT+SEND 564 564 565 -(% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %) 566 -|=(% colspan="3" style="width: 988px;" %)AT+SEND 567 -|(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response** 568 -|(% style="width:201px" %)AT+SEND=12:hello world|(% style="width:340px" %)Send text data along with the application port.|(% style="width:446px" %)OK((( 437 +|=(% colspan="3" %)AT+SEND 438 +|**Command Example**|**Function**|**Response** 439 +|AT+SEND=12:hello world|Send text data along with the application port.|OK((( 569 569 While Error in format, return 570 570 571 571 AT_BUSY_ERROR/AT_BUSY_ERROR/AT_NO_NETWORK_JOINED ... ... @@ -577,15 +577,12 @@ 577 577 578 578 Feature: Send hexadecimal data along with the application port. 579 579 580 -{{info}} 581 -**AT Command: AT+SENDB** 582 -{{/info}} 451 +AT Command: AT+SENDB 583 583 584 -(% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %) 585 -|=(% colspan="3" style="width: 1117px;" %)AT+SENDB 586 -|(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response** 587 -|(% style="width:257px" %)AT+SENDB=12:abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)OK 588 -|(% style="width:257px" %)AT+SENDB=abcdef0123456789|(% style="width:406px" %)Send hexadecimal data along with the application port.|(% style="width:453px" %)While Error in format, return((( 453 +|=(% colspan="3" %)AT+SENDB 454 +|**Command Example**|**Function**|**Response** 455 +|AT+SENDB=12:abcdef0123456789|Send hexadecimal data along with the application port.|OK 456 +|AT+SENDB=abcdef0123456789|Send hexadecimal data along with the application port.|While Error in format, return((( 589 589 AT_PARAM_ERROR AT_BUSY_ERROR/AT_NO_NETWORK_JOINED 590 590 591 591 ... ... @@ -597,46 +597,39 @@ 597 597 598 598 Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on). 599 599 600 -{{info}} 601 -**AT Command: AT+ADR** 602 -{{/info}} 603 603 604 -(% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %) 605 -|=(% colspan="3" style="width: 680px;" %)AT+ADR 606 -|(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response** 607 -|(% style="width:162px" %)AT+ADR=?|(% style="width:266px" %)Get the Adaptive Data Rate setting.|(% style="width:250px" %)1((( 469 +AT Command: AT+ADR 470 + 471 +|=(% colspan="3" %)AT+ADR 472 +|**Command Example**|**Function**|**Response** 473 +|AT+ADR=?|Get the Adaptive Data Rate setting.|1((( 608 608 OK 609 609 ))) 610 -| (% style="width:162px" %)AT+ADR=0|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)OK611 -| (% style="width:162px" %)AT+ADR=2|(% style="width:266px" %)Set the Adaptive Data Rate setting.|(% style="width:250px" %)While Error in format, return(((476 +|AT+ADR=0|Set the Adaptive Data Rate setting.|OK 477 +|AT+ADR=2|Set the Adaptive Data Rate setting.|While Error in format, return((( 612 612 AT_PARAM_ERROR 613 613 ))) 614 614 615 -{{info}} 616 -**Downlink Command: 0x22** 617 -{{/info}} 481 +Downlink Command: 0x22 618 618 619 619 620 620 If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22. 621 621 622 -* **Example 1**: Downlink Payload:**2201**~/~/ Set AT+ADR=1.623 -* **Example 2**: Downlink Payload:**2200FFFF**~/~/ Set AT+ADR=0.486 +* Example 1: Downlink Payload: 2201 ~/~/ Set AT+ADR=1. 487 +* Example 2: Downlink Payload: 2200FFFF ~/~/ Set AT+ADR=0. 624 624 625 625 == 7.2 LoRa® Class == 626 626 627 627 Feature: Get or Set the Device Class(Currently only support class A, class C). 628 628 629 -{{info}} 630 -**AT Command:AT+CLASS** 631 -{{/info}} 493 +AT Command:AT+CLASS 632 632 633 -(% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %) 634 -|=(% colspan="3" style="width: 504px;" %)AT+CLASS 635 -|(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response** 636 -|(% style="width:163px" %)AT+CLASS=?|(% style="width:166px" %)Get the Device Class.|(% style="width:175px" %)A((( 495 +|=(% colspan="3" %)AT+CLASS 496 +|**Command Example**|**Function**|**Response** 497 +|AT+CLASS=?|Get the Device Class.|A((( 637 637 OK 638 638 ))) 639 -| (% style="width:163px" %)AT+CLASS=C|(% style="width:166px" %)Set the Device Class.|(% style="width:175px" %)OK(((500 +|AT+CLASS=C|Set the Device Class.|OK((( 640 640 641 641 ))) 642 642 ... ... @@ -644,17 +644,14 @@ 644 644 645 645 Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing. 646 646 647 -{{info}} 648 -**AT Command:AT+DCS** 649 -{{/info}} 508 +AT Command:AT+DCS 650 650 651 -(% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %) 652 -|=(% colspan="3" style="width: 512px;" %)AT+DCS 653 -|(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response** 654 -|(% style="width:165px" %)AT+DCS=?|(% style="width:239px" %)Get the ETSI Duty Cycle setting.|(% style="width:107px" %)1((( 510 +|=(% colspan="3" %)AT+DCS 511 +|**Command Example**|**Function**|**Response** 512 +|AT+DCS=?|Get the ETSI Duty Cycle setting.|1((( 655 655 OK 656 656 ))) 657 -| (% style="width:165px" %)AT+DCS=1|(% style="width:239px" %)Set the ETSI Duty Cycle setting.|(% style="width:107px" %)OK(((515 +|AT+DCS=1|Set the ETSI Duty Cycle setting.|OK((( 658 658 659 659 ))) 660 660 ... ... @@ -662,45 +662,37 @@ 662 662 663 663 Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server 664 664 665 -{{info}} 666 -**AT Command: AT+DR** 667 -{{/info}} 523 +AT Command: AT+DR 668 668 669 -(% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %) 670 -|=(% colspan="3" style="width: 463px;" %)AT+DR 671 -|(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response** 672 -|(% style="width:156px" %)AT+DR=?|(% style="width:167px" %)Get the Data Rate.|(% style="width:140px" %)5((( 525 +|=(% colspan="3" %)AT+DR 526 +|**Command Example**|**Function**|**Response** 527 +|AT+DR=?|Get the Data Rate.|5((( 673 673 OK 674 674 ))) 675 -| (% style="width:156px" %)AT+DR=2|(% style="width:167px" %)Set the Data Rate.|(% style="width:140px" %)OK(((530 +|AT+DR=2|Set the Data Rate.|OK((( 676 676 677 677 ))) 678 678 679 -{{info}} 680 -**Downlink Command: 0x2200aaFF** 681 -{{/info}} 534 +Downlink Command: 0x2200aaFF 682 682 683 683 684 684 If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF. 685 685 686 -* **Example 1**: Downlink Payload:**220001FF**~/~/ Set AT+DR=1.687 -* **Example 2**: Downlink Payload:**220000FF**~/~/ Set AT+DR=0.539 +* Example 1: Downlink Payload: 220001FF ~/~/ Set AT+DR=1. 540 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+DR=0. 688 688 689 689 == 7.5 Frame Counter Downlink == 690 690 691 691 Feature: Get or Set the Frame Counter Downlink. 692 692 693 -{{info}} 694 -**AT Command:AT+FCD** 695 -{{/info}} 546 +AT Command:AT+FCD 696 696 697 -(% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %) 698 -|=(% colspan="3" style="width: 690px;" %)AT+FCD 699 -|(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response** 700 -|(% style="width:162px" %)AT+FCD=?|(% style="width:258px" %)Get the Frame Counter Downlink.|(% style="width:269px" %)0((( 548 +|=(% colspan="3" %)AT+FCD 549 +|**Command Example**|**Function**|**Response** 550 +|AT+FCD=?|Get the Frame Counter Downlink.|0((( 701 701 OK 702 702 ))) 703 -| (% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((553 +|AT+FCD=10|Set the Frame Counter Downlink.|(System will write new value to FCD)((( 704 704 OK 705 705 706 706 ... ... @@ -710,17 +710,14 @@ 710 710 711 711 Feature: Get or Set the Frame Counter Uplink. 712 712 713 -{{info}} 714 -**AT Command:AT+FCU** 715 -{{/info}} 563 +AT Command:AT+FCU 716 716 717 -(% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %) 718 -|=(% colspan="3" style="width: 531px;" %)AT+FCU 719 -|(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response** 720 -|(% style="width:177px" %)AT+FCU=?|(% style="width:239px" %)Get the Frame Counter Uplink.|(% style="width:113px" %)0((( 565 +|=(% colspan="3" %)AT+FCU 566 +|**Command Example**|**Function**|**Response** 567 +|AT+FCU=?|Get the Frame Counter Uplink.|0((( 721 721 OK 722 722 ))) 723 -| (% style="width:177px" %)AT+FCU=10|(% style="width:239px" %)Set the Frame Counter Uplink.|(% style="width:113px" %)OK(((570 +|AT+FCU=10|Set the Frame Counter Uplink.|OK((( 724 724 725 725 ))) 726 726 ... ... @@ -728,17 +728,14 @@ 728 728 729 729 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms. 730 730 731 -{{info}} 732 -**AT Command:AT+JN1DL** 733 -{{/info}} 578 +AT Command:AT+JN1DL 734 734 735 -(% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %) 736 -|=(% colspan="3" style="width: 534px;" %)AT+JN1DL 737 -|(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response** 738 -|(% style="width:164px" %)AT+JN1DL=?|(% style="width:229px" %)Get the Join Accept Delay.|(% style="width:140px" %)5000((( 580 +|=(% colspan="3" %)AT+JN1DL 581 +|**Command Example**|**Function**|**Response** 582 +|AT+JN1DL=?|Get the Join Accept Delay.|5000((( 739 739 OK 740 740 ))) 741 -| (% style="width:164px" %)AT+JN1DL=10000|(% style="width:229px" %)Set the Join Accept Delay.|(% style="width:140px" %)OK(((585 +|AT+JN1DL=10000|Set the Join Accept Delay.|OK((( 742 742 743 743 ))) 744 744 ... ... @@ -746,17 +746,14 @@ 746 746 747 747 Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms. 748 748 749 -{{info}} 750 -**AT Command:AT+JN2DL** 751 -{{/info}} 593 +AT Command:AT+JN2DL 752 752 753 -(% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %) 754 -|=(% colspan="3" style="width: 535px;" %)AT+JN2DL 755 -|(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response** 756 -|(% style="width:160px" %)AT+JN2DL=?|(% style="width:228px" %)Get the Join Accept Delay.|(% style="width:146px" %)6000((( 595 +|=(% colspan="3" %)AT+JN2DL 596 +|**Command Example**|**Function**|**Response** 597 +|AT+JN2DL=?|Get the Join Accept Delay.|6000((( 757 757 OK 758 758 ))) 759 -| (% style="width:160px" %)AT+JN2DL=20000|(% style="width:228px" %)Set the Join Accept Delay.|(% style="width:146px" %)OK(((600 +|AT+JN2DL=20000|Set the Join Accept Delay.|OK((( 760 760 761 761 ))) 762 762 ... ... @@ -764,17 +764,14 @@ 764 764 765 765 Feature: Get or Set the public network mode. (0: off, 1: on) 766 766 767 -{{info}} 768 -**AT Command:AT+PNM** 769 -{{/info}} 608 +AT Command:AT+PNM 770 770 771 -(% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %) 772 -|=(% colspan="3" style="width: 664px;" %)AT+PNM 773 -|(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response** 774 -|(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1((( 610 +|=(% colspan="3" %)AT+PNM 611 +|**Command Example**|**Function**|**Response** 612 +|AT+PNM=?|Get the public network mode.|1((( 775 775 OK 776 776 ))) 777 -| (% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((615 +|AT+PNM=1|Set the public network mode.|(System will write new value to PNM)((( 778 778 OK 779 779 780 780 ... ... @@ -784,35 +784,29 @@ 784 784 785 785 Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms 786 786 787 -{{info}} 788 -**AT Command:AT+RX1DL** 789 -{{/info}} 625 +AT Command:AT+RX1DL 790 790 791 -(% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %) 792 -|=(% colspan="3" style="width: 405px;" %)AT+RX1DL 793 -|(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response** 794 -|(% style="width:155px" %)AT+RX1DL=?|(% style="width:128px" %)Get the delay.|(% style="width:122px" %)1000((( 627 +|=(% colspan="3" %)AT+RX1DL 628 +|**Command Example**|**Function**|**Response** 629 +|AT+RX1DL=?|Get the delay.|1000((( 795 795 OK 796 796 ))) 797 -| (% style="width:155px" %)AT+RX1DL=1500|(% style="width:128px" %)Set the delay.|(% style="width:122px" %)OK(((632 +|AT+RX1DL=1500|Set the delay.|OK((( 798 798 799 799 ))) 800 800 801 -== 7.11 636 +== 7.11Receive Delay2 == 802 802 803 803 Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms 804 804 805 -{{info}} 806 -**AT Command:AT+RX2DL** 807 -{{/info}} 640 +AT Command:AT+RX2DL 808 808 809 -(% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %) 810 -|=(% colspan="3" style="width: 478px;" %)AT+RX2DL 811 -|(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response** 812 -|(% style="width:175px" %)AT+RX2DL=?|(% style="width:152px" %)Get the delay.|(% style="width:150px" %)2000((( 642 +|=(% colspan="3" %)AT+RX2DL 643 +|**Command Example**|**Function**|**Response** 644 +|AT+RX2DL=?|Get the delay.|2000((( 813 813 OK 814 814 ))) 815 -| (% style="width:175px" %)AT+RX2DL=2500|(% style="width:152px" %)Set the delay.|(% style="width:150px" %)OK(((647 +|AT+RX2DL=2500|Set the delay.|OK((( 816 816 817 817 ))) 818 818 ... ... @@ -820,17 +820,14 @@ 820 820 821 821 Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X) 822 822 823 -{{info}} 824 -**AT Command:AT+RX2DR** 825 -{{/info}} 655 +AT Command:AT+RX2DR 826 826 827 -(% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %) 828 -|=(% colspan="3" style="width: 522px;" %)AT+RX2DR 829 -|(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response** 830 -|(% style="width:160px" %)AT+RX2DR=?|(% style="width:232px" %)Get the Rx2 window data rate.|(% style="width:130px" %)2((( 657 +|=(% colspan="3" %)AT+RX2DR 658 +|**Command Example**|**Function**|**Response** 659 +|AT+RX2DR=?|Get the Rx2 window data rate.|2((( 831 831 OK 832 832 ))) 833 -| (% style="width:160px" %)AT+RX2DR=6|(% style="width:232px" %)Set the Rx2 window data rate.|(% style="width:130px" %)OK(((662 +|AT+RX2DR=6|Set the Rx2 window data rate.|OK((( 834 834 835 835 ))) 836 836 ... ... @@ -838,17 +838,14 @@ 838 838 839 839 Feature: Get or Set the Rx2 window frequency 840 840 841 -{{info}} 842 -**AT Command:AT+RX2FQ** 843 -{{/info}} 670 +AT Command:AT+RX2FQ 844 844 845 -(% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %) 846 -|=(% colspan="3" style="width: 584px;" %)AT+RX2FQ 847 -|(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response** 848 -|(% style="width:183px" %)AT+RX2FQ=?|(% style="width:240px" %)Get the Rx2 window frequency.|(% style="width:160px" %)434665000((( 672 +|=(% colspan="3" %)AT+RX2FQ 673 +|**Command Example**|**Function**|**Response** 674 +|AT+RX2FQ=?|Get the Rx2 window frequency.|434665000((( 849 849 OK 850 850 ))) 851 -| (% style="width:183px" %)AT+RX2FQ=434665000|(% style="width:240px" %)Set the Rx2 window frequency.|(% style="width:160px" %)OK(((677 +|AT+RX2FQ=434665000|Set the Rx2 window frequency.|OK((( 852 852 853 853 ))) 854 854 ... ... @@ -856,17 +856,14 @@ 856 856 857 857 Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. ) 858 858 859 -{{info}} 860 -**AT Command:AT+TXP** 861 -{{/info}} 685 +AT Command:AT+TXP 862 862 863 -(% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %) 864 -|=(% colspan="3" style="width: 462px;" %)AT+TXP 865 -|(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response** 866 -|(% style="width:161px" %)AT+TXP=?|(% style="width:189px" %)Get the Transmit Power.|(% style="width:112px" %)0((( 687 +|=(% colspan="3" %)AT+TXP 688 +|**Command Example**|**Function**|**Response** 689 +|AT+TXP=?|Get the Transmit Power.|0((( 867 867 OK 868 868 ))) 869 -| (% style="width:161px" %)AT+TXP=1|(% style="width:189px" %)Set the Transmit Power.|(% style="width:112px" %)OK(((692 +|AT+TXP=1|Set the Transmit Power.|OK((( 870 870 871 871 ))) 872 872 ... ... @@ -874,21 +874,18 @@ 874 874 875 875 If the downlink payload=22000100, it means setting the TXP to 0. 876 876 877 -* **Example 1**: Downlink Payload:**22000102**~/~/ Set AT+TXP=2.878 -* **Example 2**: Downlink Payload:**220000FF**~/~/ Set AT+TXP=0.700 +* Example 1: Downlink Payload: 22000102 ~/~/ Set AT+TXP=2. 701 +* Example 2: Downlink Payload: 220000FF ~/~/ Set AT+TXP=0. 879 879 880 880 == 7.15 RSSI of the Last Received Packet == 881 881 882 882 Feature: Get or Set the Rx2 window frequency 883 883 884 -{{info}} 885 -**AT Command:AT+RSSI** 886 -{{/info}} 707 +AT Command:AT+RSSI 887 887 888 -(% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %) 889 -|=(% colspan="3" style="width: 554px;" %)AT+RSSI 890 -|(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response** 891 -|(% style="width:164px" %)AT+RSSI=?|(% style="width:289px" %)Get the RSSI of the last received packet.|(% style="width:100px" %)0((( 709 +|=(% colspan="3" %)AT+RSSI 710 +|**Command Example**|**Function**|**Response** 711 +|AT+RSSI=?|Get the RSSI of the last received packet.|0((( 892 892 OK 893 893 ))) 894 894 ... ... @@ -896,14 +896,11 @@ 896 896 897 897 Feature: Get the SNR of the last received packet 898 898 899 -{{info}} 900 -**AT Command:AT+SNR** 901 -{{/info}} 719 +AT Command:AT+SNR 902 902 903 -(% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %) 904 -|=(% colspan="3" style="width: 568px;" %)AT+SNR 905 -|(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response** 906 -|(% style="width:164px" %)AT+SNR=?|(% style="width:290px" %)Get the RSSI of the last received packet.|(% style="width:113px" %)0((( 721 +|=(% colspan="3" %)AT+SNR 722 +|**Command Example**|**Function**|**Response** 723 +|AT+SNR=?|Get the RSSI of the last received packet.|0((( 907 907 OK 908 908 ))) 909 909 ... ... @@ -911,144 +911,114 @@ 911 911 912 912 Feature: Get or set the application port. 913 913 914 -{{info}} 915 -**AT Command: AT+PORT** 916 -{{/info}} 731 +AT Command: AT+PORT 917 917 918 -(% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %) 919 -|=(% colspan="3" style="width: 497px;" %)AT+PORT 920 -|(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response** 921 -|(% style="width:157px" %)AT+PORT=?|(% style="width:204px" %)Get the application port|(% style="width:135px" %)21((( 733 +|=(% colspan="3" %)AT+PORT 734 +|**Command Example**|**Function**|**Response** 735 +|AT+PORT=?|Get the application port|21((( 922 922 OK 923 923 ))) 924 -| (% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK738 +|AT+PORT=21|Set the application port|OK 925 925 926 -{{info}} 927 -**Downlink Command: 0x23** 928 -{{/info}} 740 +Downlink Command: 0x23 929 929 930 930 Format: Command Code (0x23) followed by 1 bytes port value. 931 931 932 932 If the downlink payload=2301, it means set the application port to 1, while type code is 23. 933 933 934 -* **Example 1**: Downlink Payload:**2301**~/~/ set the application port to 1935 -* **Example 2**: Downlink Payload:**2305**~/~/ set the application port to 5746 +* Example 1: Downlink Payload: 2301 ~/~/ set the application port to 1 747 +* Example 2: Downlink Payload: 2305 ~/~/ set the application port to 5 936 936 937 937 == 7.18 Single Channel Mode == 938 938 939 939 Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode. 940 940 941 -{{info}} 942 -**AT Command: AT+CHS** 943 -{{/info}} 753 +AT Command: AT+CHS 944 944 945 -(% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %) 946 -|=(% colspan="3" style="width: 600px;" %)AT+CHS 947 -|(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response** 948 -|(% style="width:182px" %)AT+CHS=?|(% style="width:295px" %)Get Frequency for Single Channel Mode|(% style="width:122px" %)0((( 755 +|=(% colspan="3" %)AT+CHS 756 +|**Command Example**|**Function**|**Response** 757 +|AT+CHS=?|Get Frequency for Single Channel Mode|0((( 949 949 OK 950 950 ))) 951 -| (% style="width:182px" %)AT+CHS=868100000|(% style="width:295px" %)Set Frequency for Single Channel Mode|(% style="width:122px" %)OK760 +|AT+CHS=868100000|Set Frequency for Single Channel Mode|OK 952 952 953 953 == 7.19 Eight Channel Mode == 954 954 955 955 Feature: Get or Set eight channels mode,Only for US915,AU915,CN470. 956 956 957 -{{info}} 958 -**AT Command: AT+CHE** 959 -{{/info}} 766 +AT Command: AT+CHE 960 960 961 -(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %) 962 -|=(% colspan="3" style="width: 707px;" %)AT+CHE 963 -|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response** 964 -|(% style="width:160px" %)AT+CHE=?|(% style="width:198px" %)Get eight channels mode|(% style="width:349px" %)1((( 768 +|=(% colspan="3" %)AT+CHE 769 +|**Command Example**|**Function**|**Response** 770 +|AT+CHE=?|Get eight channels mode|1((( 965 965 902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7 966 966 967 967 OK 968 968 ))) 969 -| (% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK775 +|AT+CHE=1|Set eight channels mode|OK 970 970 971 -{{info}} 972 -**Downlink Command: 0x24** 973 -{{/info}} 777 +Downlink Command: 0x24 974 974 975 975 Format: Command Code (0x24) followed by 1 bytes channel value. 976 976 977 977 If the downlink payload=2401, it means set channel mode to 1, while type code is 24. 978 978 979 -* **Example 1**: Downlink Payload: 2401 ~/~/ set channel mode to 1980 -* **Example 2**: Downlink Payload: 2405 ~/~/ set channel mode to 5783 +* Example 1: Downlink Payload: 2401 ~/~/ set channel mode to 1 784 +* Example 2: Downlink Payload: 2405 ~/~/ set channel mode to 5 981 981 982 982 == 7.20 Get or Set RXwindows1 timeout == 983 983 984 984 Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255). 985 985 986 -{{info}} 987 -**AT Command: AT+RX1WTO** 988 -{{/info}} 790 +AT Command: AT+RX1WTO 989 989 990 -(% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %) 991 -|=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO 992 -|(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response** 993 -|(% style="width:163px" %)AT+RX1WTO=?|(% style="width:201px" %)Get RXwindows1 timeout|(% style="width:93px" %)14((( 792 +|=(% colspan="3" %)AT+ RX1WTO 793 +|**Command Example**|**Function**|**Response** 794 +|AT+RX1WTO=?|Get RXwindows1 timeout|14((( 994 994 OK 995 995 ))) 996 -| (% style="width:163px" %)AT+RX1WTO=60|(% style="width:201px" %)Set RXwindows1 timeout|(% style="width:93px" %)OK797 +|AT+RX1WTO=60|Set RXwindows1 timeout|OK 997 997 998 -((( 999 -**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph. 1000 -))) 799 +AT+RX1TWO is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph. 1001 1001 1002 -[[image:image -20220526162535-1.png]]801 +[[~[~[image:https://wiki.dragino.com/images/thumb/5/51/RX1WTO.JPG/600px-RX1WTO.JPG~|~|alt="RX1WTO.JPG" height="239" width="600"~]~]>>url:https://wiki.dragino.com/index.php/File:RX1WTO.JPG]] 1003 1003 1004 -((( 1005 1005 Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink. 1006 1006 1007 - 1008 -))) 1009 - 1010 1010 == 7.21 Get or Set RXwindows2 timeout == 1011 1011 1012 1012 Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255). 1013 1013 1014 -{{info}} 1015 -**AT Command: AT+RX2WTO** 1016 -{{/info}} 809 +AT Command: AT+RX2WTO 1017 1017 1018 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %) 1019 -|=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO 1020 -|(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response** 1021 -|(% style="width:190px" %)AT+RX2WTO=?|(% style="width:199px" %)Get RXwindows2 timeout|(% style="width:104px" %)7((( 811 +|=(% colspan="3" %)AT+ RX2WTO 812 +|**Command Example**|**Function**|**Response** 813 +|AT+RX2WTO=?|Get RXwindows2 timeout|7((( 1022 1022 OK 1023 1023 ))) 1024 -| (% style="width:190px" %)AT+RX2WTO=20|(% style="width:199px" %)Set RXwindows2 timeout|(% style="width:104px" %)OK816 +|AT+RX2WTO=20|Set RXwindows2 timeout|OK 1025 1025 1026 1026 == 7.22 Setting up uplinkdwelltime (as923, au915) == 1027 1027 1028 1028 Feature: Get or Set uplinkdwelltime 1029 1029 1030 -{{info}} 1031 -**AT Command: AT+DWELLT** 1032 -{{/info}} 822 +AT Command: AT+DWELLT 1033 1033 1034 -(% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %) 1035 -|=(% colspan="3" style="width: 494px;" %)AT+DWELLT 1036 -|(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response** 1037 -|(% style="width:183px" %)AT+DWELLT=?|(% style="width:179px" %)Get uplinkdwelltime|(% style="width:131px" %)1((( 824 +|=(% colspan="3" %)AT+DWELLT 825 +|**Command Example**|**Function**|**Response** 826 +|AT+DWELLT=?|Get uplinkdwelltime|1((( 1038 1038 OK 1039 1039 ))) 1040 -| (% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK829 +|AT+DWELLT=0|Set uplinkdwelltime|OK 1041 1041 1042 -{{info}} 1043 -**Downlink Command: 0x25** 1044 -{{/info}} 831 +Downlink Command: 0x25 1045 1045 1046 1046 Format: Command Code (0x25) followed by 1 bytes state value. 1047 1047 1048 1048 If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25. 1049 1049 1050 -* **Example 1**: Downlink Payload:**2501**~/~/ set uplinkdwelltime to 11051 -* **Example 2**: Downlink Payload:**2500**~/~/ set uplinkdwelltime to 0837 +* Example 1: Downlink Payload: 2501 ~/~/ set uplinkdwelltime to 1 838 +* Example 2: Downlink Payload: 2500 ~/~/ set uplinkdwelltime to 0 1052 1052 1053 1053 == 7.23 Set Packet Receiving Response Level == 1054 1054 ... ... @@ -1056,11 +1056,11 @@ 1056 1056 1057 1057 RPL value: 1058 1058 1059 -* **AT+RPL=0:**Device won't immediately reply any downlink commands from platform.1060 -* **AT+RPL=1:**Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00.1061 -* **AT+RPL=2:**Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command.1062 -* **AT+RPL=3:**Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command.1063 -* **AT+RPL=4:**Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands.846 +* AT+RPL=0: Device won't immediately reply any downlink commands from platform. 847 +* AT+RPL=1: Device will immediately reply message to Unconfirmed Data Down. Payload is 0x00. 848 +* AT+RPL=2: Device will immediately reply message to Confirmed Data Down. Payload is 0x00 and requied response header for this command. 849 +* AT+RPL=3: Device will immediately reply message to MAC Command. Payload is 0x00 and requied response header for this command. 850 +* AT+RPL=4: Device will immediately reply message to Confirmed Data Down & MAC Command. Payload is 0x00 and requied response header for these two commands. 1064 1064 1065 1065 Case Analyes: 1066 1066 ... ... @@ -1068,44 +1068,37 @@ 1068 1068 * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command. 1069 1069 * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command. 1070 1070 1071 -{{info}} 1072 -**AT Command: AT+RPL** 1073 -{{/info}} 858 +AT Command: AT+RPL 1074 1074 1075 -(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %) 1076 -|=(% colspan="3" style="width: 533px;" %)AT+RPL 1077 -|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response** 1078 -|(% style="width:160px" %)AT+RPL=?|(% style="width:263px" %)Get packet receiving response level|(% style="width:109px" %)1((( 860 +|=(% colspan="3" %)AT+RPL 861 +|**Command Example**|**Function**|**Response** 862 +|AT+RPL=?|Get packet receiving response level|1((( 1079 1079 OK 1080 1080 ))) 1081 -| (% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK865 +|AT+RPL=0|Set packet receiving response level|OK 1082 1082 1083 -{{info}} 1084 -**Downlink Command: 0x21** 1085 -{{/info}} 867 +Downlink Command: 0x21 1086 1086 1087 1087 Format: Command Code (0x21) followed by 1 bytes level value. 1088 1088 1089 1089 If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21. 1090 1090 1091 -* **Example 1**: Downlink Payload:**2101**~/~/ set packet receiving response level to 11092 -* **Example 2**: Downlink Payload:**2102**~/~/ set packet receiving response level to 2873 +* Example 1: Downlink Payload: 2101 ~/~/ set packet receiving response level to 1 874 +* Example 2: Downlink Payload: 2102 ~/~/ set packet receiving response level to 2 1093 1093 1094 1094 = 8. AT Commands Combination = 1095 1095 1096 1096 == 8.1 Set a fix RX2DR for downlink window == 1097 1097 1098 -* **AT+ADR=0**~-~-> Disable ADR first1099 -* **AT+RX2DR=xxxx**~-~-> Set xxxx to your wanted DataRate880 +* AT+ADR=0 ~-~-> Disable ADR first 881 +* AT+RX2DR=xxxx ~-~-> Set xxxx to your wanted DataRate 1100 1100 1101 1101 == 8.2 Use Downlink Command to set a fix uplink DR == 1102 1102 1103 -{{info}} 1104 -**Downlink Command: 0x22000500** 1105 -{{/info}} 885 +Downlink Command: 0x22000500 1106 1106 1107 1107 Same as: 1108 1108 1109 -* AT+ADR=0 ||anchor="H7.1AdaptiveDataRate"]]1110 -* AT+DR=5 ||anchor="H7.4DataRate"]]1111 -* AT+TXP=0 ||anchor="H7.14TransmitPower"]]889 +* AT+ADR=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Adaptive_Data_Rate]] 890 +* AT+DR=5 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Data_Rate]] 891 +* AT+TXP=0 [[Reference>>url:https://wiki.dragino.com/index.php/End_Device_Downlink_Command#Transmit_Power]]
- image-20220511120050-1.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.Xiaoling - Size
-
... ... @@ -1,1 +1,0 @@ 1 -136.3 KB - Content
- image-20220526162535-1.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.Xiaoling - Size
-
... ... @@ -1,1 +1,0 @@ 1 -149.4 KB - Content