Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -139,6 +139,7 @@
139	139	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140	140
141	141
	141	+
142	142	== 4.2 Reboot End Node ==
143	143
144	144	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -321,6 +321,7 @@
321	321	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
322	322
323	323
	324	+
324	324	== 5.2 Application Key ==
325	325
326	326	Feature: Get or Set the Application Key.
...	...	@@ -338,6 +338,7 @@
338	338	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
339	339
340	340
	342	+
341	341	== 5.3 Application Session Key ==
342	342
343	343	Feature: Get or Set the Application Session Key.
...	...	@@ -356,8 +356,6 @@
356	356	OK
357	357	)))
358	358
359		-
360		-
361	361	== 5.4 Device Address ==
362	362
363	363	Feature: Get or Set the Device Address.
...	...	@@ -376,8 +376,6 @@
376	376	)))
377	377	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
378	378
379		-
380		-
381	381	== 5.5 Device EUI ==
382	382
383	383	Feature: Get or Set the Device EUI.
...	...	@@ -396,8 +396,6 @@
396	396	OK
397	397	)))
398	398
399		-
400		-
401	401	== 5.6 Network ID ==
402	402
403	403	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -414,8 +414,6 @@
414	414	)))
415	415	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
416	416
417		-
418		-
419	419	== 5.7 Network Session Key ==
420	420
421	421	Feature: Get or Set the Network Session Key
...	...	@@ -432,8 +432,6 @@
432	432	)))
433	433	|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
434	434
435		-
436		-
437	437	= 6. Joining and sending date on LoRaWAN network =
438	438
439	439	== 6.1 Confirm Mode ==
...	...	@@ -462,8 +462,6 @@
462	462	* Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
463	463	* Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
464	464
465		-
466		-
467	467	== 6.2 Confirm Status ==
468	468
469	469	Feature: Get confirmation status of the last AT+SEND (0-1).
...	...	@@ -479,8 +479,6 @@
479	479	OK
480	480	)))
481	481
482		-
483		-
484	484	== 6.3 Join LoRa® Network ==
485	485
486	486	Feature: Join network.
...	...	@@ -815,7 +815,7 @@
815	815
816	816	)))
817	817
818		-== 7.11 Receive Delay2 ==
	806	+== 7.11Receive Delay2 ==
819	819
820	820	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
821	821
...	...	@@ -1020,8 +1020,6 @@
1020	1020
1021	1021	(((
1022	1022	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1023		-
1024		-
1025	1025	)))
1026	1026
1027	1027	== 7.21 Get or Set RXwindows2 timeout ==