Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -139,6 +139,7 @@
139	139	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
140	140
141	141
	141	+
142	142	== 4.2 Reboot End Node ==
143	143
144	144	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -321,6 +321,7 @@
321	321	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
322	322
323	323
	324	+
324	324	== 5.2 Application Key ==
325	325
326	326	Feature: Get or Set the Application Key.
...	...	@@ -338,6 +338,7 @@
338	338	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
339	339
340	340
	342	+
341	341	== 5.3 Application Session Key ==
342	342
343	343	Feature: Get or Set the Application Session Key.
...	...	@@ -356,8 +356,6 @@
356	356	OK
357	357	)))
358	358
359		-
360		-
361	361	== 5.4 Device Address ==
362	362
363	363	Feature: Get or Set the Device Address.
...	...	@@ -376,8 +376,6 @@
376	376	)))
377	377	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
378	378
379		-
380		-
381	381	== 5.5 Device EUI ==
382	382
383	383	Feature: Get or Set the Device EUI.
...	...	@@ -396,8 +396,6 @@
396	396	OK
397	397	)))
398	398
399		-
400		-
401	401	== 5.6 Network ID ==
402	402
403	403	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -807,7 +807,7 @@
807	807
808	808	)))
809	809
810		-== 7.11 Receive Delay2 ==
	806	+== 7.11Receive Delay2 ==
811	811
812	812	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
813	813
...	...	@@ -1012,8 +1012,6 @@
1012	1012
1013	1013	(((
1014	1014	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1015		-
1016		-
1017	1017	)))
1018	1018
1019	1019	== 7.21 Get or Set RXwindows2 timeout ==