Last modified by kai on 2024/09/06 10:00
<
From version < 38.123 >
edited by Xiaoling
on 2022/06/01 11:57
To version < 50.18 >
edited by Xiaoling
on 2022/07/13 13:49
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,4 @@
1 - **Contents：**
1 + **Table of** **Contents：**
2 2  
3 3  {{toc/}}
4 4  
... ... @@ -6,6 +6,7 @@
6 6  
7 7  = 1. Introduction =
8 8  
9 +
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10 10  
11 11  * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
... ... @@ -18,6 +18,7 @@
18 18  
19 19  = 2. How to use AT Commands or Downlink command =
20 20  
22 +
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 23  ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
... ... @@ -28,6 +28,7 @@
28 28  
29 29  = 3. Support End Node and firmware version =
30 30  
33 +
31 31  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
32 32  |=(% colspan="3" style="width: 963px;" %)(((
33 33  Dragino STM32 base hardware Firmware / LoRaWAN stack list
... ... @@ -100,18 +100,17 @@
100 100  )))
101 101  
102 102  
103 -
104 104  = 4. System Management Commands =
105 105  
108 +
106 106  == 4.1 Change Uplink Interval ==
107 107  
111 +
108 108  Feature: Change LoRaWAN End Node Transmit Interval.
109 109  
110 -(% class="box infomessage" %)
111 -(((
112 -**AT Command: AT+TDC**
113 -)))
114 114  
115 +(% style="color:blue" %)**AT Command: AT+TDC**
116 +
115 115  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
116 116  |=(% colspan="3" style="width: 724px;" %)AT+TDC
117 117  |(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
... ... @@ -124,11 +124,11 @@
124 124  Set transmit interval to 60000ms = 60 seconds
125 125  )))
126 126  
127 -{{info}}
128 -**Downlink Command: 0x01**
129 -{{/info}}
130 -
131 131  (((
130 +
131 +
132 +(% style="color:blue" %)**Downlink Command: 0x01**
133 +
132 132  Format: Command Code (0x01) followed by 3 bytes time value.
133 133  )))
134 134  
... ... @@ -143,12 +143,12 @@
143 143  
144 144  == 4.2 Reboot End Node ==
145 145  
148 +
146 146  Feature: Reboot End Node to perform a new OTAA or ABP Join.
147 147  
148 -{{info}}
149 -**AT Command: ATZ**
150 -{{/info}}
151 151  
152 +(% style="color:blue" %)**AT Command: ATZ**
153 +
152 152  (% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
153 153  |=(% colspan="3" %)ATZ: Trig a reset of the MCU
154 154  |**Command Example**|**Function**|**Response**
... ... @@ -166,10 +166,9 @@
166 166  <followed by the Tx and Rx information>
167 167  )))
168 168  
169 -{{info}}
170 -**Downlink Command: 0x04**
171 -{{/info}}
172 172  
172 +(% style="color:blue" %)**Downlink Command: 0x04**
173 +
173 173  (((
174 174  Format: Command Code (0x04) followed by FF.
175 175  )))
... ... @@ -182,12 +182,12 @@
182 182  
183 183  == 4.3 Reset to factory Default ==
184 184  
186 +
185 185  Feature: Reset the parameters to Factory Default, factory default value depends on the firmware settings, the OTAA and ABP keys will reserve after this command.
186 186  
187 -{{info}}
188 -**AT Command: AT+FDR**
189 -{{/info}}
190 190  
190 +(% style="color:blue" %)**AT Command: AT+FDR**
191 +
191 191  (% border="1" style="background-color:#ffffcc; color:green; width:831.222px" %)
192 192  |=(% colspan="3" style="width: 828px;" %)Reset to factory default
193 193  |(% style="width:181px" %)**Command Example**|(% style="width:181px" %)**Function**|(% style="width:465px" %)**Response**
... ... @@ -205,10 +205,9 @@
205 205  Please set the parameters or reset Device to apply change
206 206  )))
207 207  
208 -{{info}}
209 -**Downlink Command: 0x04**
210 -{{/info}}
211 211  
210 +(% style="color:blue" %)**Downlink Command: 0x04**
211 +
212 212  (((
213 213  Format: Command Code (0x04) followed by FE.
214 214  )))
... ... @@ -220,12 +220,12 @@
220 220  
221 221  == 4.4 Show Firmware Version ==
222 222  
223 +
223 223  Feature: Show firmware version. No downlink command yet.
224 224  
225 -{{info}}
226 -**AT Command: AT+VER**
227 -{{/info}}
228 228  
227 +(% style="color:blue" %)**AT Command: AT+VER**
228 +
229 229  (% border="1" style="background-color:#ffffcc; color:green; width:586px" %)
230 230  |=(% colspan="3" style="width: 583px;" %)AT+VER: Image Version and Frequency Band
231 231  |(% style="width:170px" %)**Command Example**|(% style="width:300px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -235,10 +235,9 @@
235 235  OK
236 236  )))
237 237  
238 -{{info}}
239 -**Downlink Command: 0x26 (Valid in 006 stack)**
240 -{{/info}}
241 241  
239 +(% style="color:blue" %)**Downlink Command: 0x26 (Valid in 006 stack)**
240 +
242 242  (((
243 243  Downlink Format: 0x26
244 244  )))
... ... @@ -248,6 +248,9 @@
248 248  )))
249 249  
250 250  (((
250 +
251 +
252 +
251 251  **xx: Software Type:**
252 252  )))
253 253  
... ... @@ -256,6 +256,9 @@
256 256  * 0x00 03: LSE01/LDDS75/LDDS20/LSPH01/LLMS01/LSNPK01
257 257  
258 258  (((
261 +
262 +
263 +
259 259  **yy: Frequency Band:**
260 260  )))
261 261  
... ... @@ -271,6 +271,9 @@
271 271  * 0xa0: AS923-3
272 272  
273 273  (((
279 +
280 +
281 +
274 274  **zz: Subband**
275 275  )))
276 276  
... ... @@ -279,12 +279,12 @@
279 279  
280 280  == 4.5 Show System Configure ==
281 281  
290 +
282 282  Feature: Show All configure. No downlink command yet.
283 283  
284 -{{info}}
285 -**AT Command: AT+CFG**
286 -{{/info}}
287 287  
294 +(% style="color:blue" %)**AT Command: AT+CFG**
295 +
288 288  (% border="1" style="background-color:#ffffcc; color:green; width:599.222px" %)
289 289  |=(% colspan="3" style="width: 596px;" %)AT+CFG: Print all configurations
290 290  |(% style="width:160px" %)**Command Example**|(% style="width:154px" %)**Function**|(% style="width:280px" %)**Response**
... ... @@ -306,14 +306,15 @@
306 306  
307 307  = 5. Keys, IDs and EUIs management =
308 308  
317 +
309 309  == 5.1 Application EUI ==
310 310  
320 +
311 311  Feature: Get or Set the Application EUI.
312 312  
313 -{{info}}
314 -**AT Command: AT+APPEUI**
315 -{{/info}}
316 316  
324 +(% style="color:blue" %)**AT Command: AT+APPEUI**
325 +
317 317  (% border="1" style="background-color:#ffffcc; color:green; width:686.222px" %)
318 318  |=(% colspan="3" style="width: 683px;" %)AT+APPEUI
319 319  |(% style="width:305px" %)**Command Example**|(% style="width:186px" %)**Function**|(% style="width:191px" %)**Response**
... ... @@ -326,12 +326,12 @@
326 326  
327 327  == 5.2 Application Key ==
328 328  
338 +
329 329  Feature: Get or Set the Application Key.
330 330  
331 -{{info}}
332 -**AT Command: AT+APPKEY**
333 -{{/info}}
334 334  
342 +(% style="color:blue" %)**AT Command: AT+APPKEY**
343 +
335 335  (% border="1" style="background-color:#ffffcc; color:green; width:976.222px" %)
336 336  |=(% colspan="3" style="width: 973px;" %)AT+APPKEY
337 337  |(% style="width:441px" %)**Command Example**|(% style="width:180px" %)**Function**|(% style="width:350px" %)**Response**
... ... @@ -344,12 +344,12 @@
344 344  
345 345  == 5.3 Application Session Key ==
346 346  
356 +
347 347  Feature: Get or Set the Application Session Key.
348 348  
349 -{{info}}
350 -**AT Command: AT+APPSKEY**
351 -{{/info}}
352 352  
360 +(% style="color:blue" %)**AT Command: AT+APPSKEY**
361 +
353 353  (% border="1" style="background-color:#ffffcc; color:green; width:1040.22px" %)
354 354  |=(% colspan="3" style="width: 1037px;" %)AT+APPSKEY
355 355  |(% style="width:451px" %)**Command Example**|(% style="width:231px" %)**Function**|(% style="width:354px" %)**Response**
... ... @@ -364,12 +364,12 @@
364 364  
365 365  == 5.4 Device Address ==
366 366  
376 +
367 367  Feature: Get or Set the Device Address.
368 368  
369 -{{info}}
370 -**AT Command: AT+DADDR**
371 -{{/info}}
372 372  
380 +(% style="color:blue" %)**AT Command: AT+DADDR**
381 +
373 373  (% border="1" style="background-color:#ffffcc; color:green; width:795.222px" %)
374 374  |=(% colspan="3" style="width: 792px;" %)AT+DADDR
375 375  |(% style="width:192px" %)**Command Example**|(% style="width:241px" %)**Function**|(% style="width:359px" %)**Response**
... ... @@ -384,12 +384,12 @@
384 384  
385 385  == 5.5 Device EUI ==
386 386  
396 +
387 387  Feature: Get or Set the Device EUI.
388 388  
389 -{{info}}
390 -**AT Command: AT+DEUI**
391 -{{/info}}
392 392  
400 +(% style="color:blue" %)**AT Command: AT+DEUI**
401 +
393 393  (% border="1" style="background-color:#ffffcc; color:green; width:1035.22px" %)
394 394  |=(% colspan="3" style="width: 1032px;" %)AT+DEUI
395 395  |(% style="width:250px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:634px" %)**Response**
... ... @@ -404,12 +404,12 @@
404 404  
405 405  == 5.6 Network ID ==
406 406  
416 +
407 407  Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
408 408  
409 -{{info}}
410 -**AT Command: AT+NWKID**
411 -{{/info}}
412 412  
420 +(% style="color:blue" %)**AT Command: AT+NWKID**
421 +
413 413  (% border="1" style="background-color:#ffffcc; color:green; width:448.222px" %)
414 414  |=(% colspan="3" style="width: 445px;" %)AT+NWKID
415 415  |(% style="width:191px" %)**Command Example**|(% style="width:153px" %)**Function**|(% style="width:101px" %)**Response**
... ... @@ -422,12 +422,12 @@
422 422  
423 423  == 5.7 Network Session Key ==
424 424  
434 +
425 425  Feature: Get or Set the Network Session Key
426 426  
427 -{{info}}
428 -**AT Command: AT+NWKSKEY**
429 -{{/info}}
430 430  
438 +(% style="color:blue" %)**AT Command: AT+NWKSKEY**
439 +
431 431  (% border="1" style="background-color:#ffffcc; color:green; width:1017.22px" %)
432 432  |=(% colspan="3" style="width: 1014px;" %)AT+NWKSKEY
433 433  |(% style="width:455px" %)**Command Example**|(% style="width:215px" %)**Function**|(% style="width:343px" %)**Response**
... ... @@ -440,14 +440,18 @@
440 440  
441 441  = 6. Joining and sending date on LoRaWAN network =
442 442  
452 +
443 443  == 6.1 Confirm Mode ==
444 444  
455 +
456 +=== 6.1.1  AT+CFM command before DR-LWS007 software stack ===
457 +
458 +
445 445  Feature: Get or Set the confirmation mode (0-1).
446 446  
447 -{{info}}
448 -**AT Command: AT+CFM**
449 -{{/info}}
450 450  
462 +(% style="color:blue" %)**AT Command: AT+CFM**
463 +
451 451  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
452 452  |=(% colspan="3" style="width: 707px;" %)AT+CFM
453 453  |(% style="width:155px" %)**Command Example**|(% style="width:205px" %)**Function**|(% style="width:346px" %)**Response**
... ... @@ -457,8 +457,9 @@
457 457  |(% style="width:155px" %)AT+CFM=1|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)OK
458 458  |(% style="width:155px" %)AT+CFM=2|(% style="width:205px" %)Set the confirmation mode|(% style="width:346px" %)While Error in format, return AT_PARAM_ERROR
459 459  
460 -Downlink Command: 0x05
461 461  
474 +(% style="color:blue" %)**Downlink Command: 0x05**
475 +
462 462  Format: Command Code (0x05) followed by 2 bytes mode value.
463 463  
464 464  If the downlink payload=0501, it means set end node to use confirm mode, while type code is 05.
... ... @@ -468,14 +468,64 @@
468 468  
469 469  
470 470  
485 +
486 +=== 6.1.2  AT+CFM command since DR-LWS007 software stack ===
487 +
488 +
489 +(% style="color:blue" %)**AT Command: AT+CFM**
490 +
491 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
492 +|=(% colspan="3" style="width: 707px;" %)AT+CFM
493 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
494 +|(% style="width:160px" %)(((
495 +AT+CFM=1,0,0
496 +
497 +value1
498 +)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
499 +1
500 +
501 +OK
502 +)))
503 +|(% style="width:160px" %)(((
504 +AT+CFM=0,?,0
505 +
506 +value2
507 +)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
508 +0~~7
509 +
510 +OK
511 +)))
512 +|(% style="width:160px" %)(((
513 +AT+CFM=0,0,1
514 +
515 +value3
516 +)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
517 +1
518 +
519 +OK
520 +)))
521 +
522 +
523 +(% style="color:blue" %)**Downlink Command: 0x05**
524 +
525 +Format: Command Code (0x05) followed by 2 bytes mode value.
526 +
527 +If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
528 +
529 +* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
530 +* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
531 +
532 +
533 +
534 +
471 471  == 6.2 Confirm Status ==
472 472  
537 +
473 473  Feature: Get confirmation status of the last AT+SEND (0-1).
474 474  
475 -{{info}}
476 -**AT Command: AT+CFS**
477 -{{/info}}
478 478  
541 +(% style="color:blue" %)**AT Command: AT+CFS**
542 +
479 479  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
480 480  |=(% colspan="3" style="width: 531px;" %)AT+CFS
481 481  |(% style="width:156px" %)**Command Example**|(% style="width:193px" %)**Function**|(% style="width:178px" %)**Response**
... ... @@ -487,12 +487,12 @@
487 487  
488 488  == 6.3 Join LoRa® Network ==
489 489  
554 +
490 490  Feature: Join network.
491 491  
492 -{{info}}
493 -**AT Command: AT+JOIN**
494 -{{/info}}
495 495  
558 +(% style="color:blue" %)**AT Command: AT+JOIN**
559 +
496 496  (% border="1" style="background-color:#ffffcc; color:green; width:647.222px" %)
497 497  |=(% colspan="3" style="width: 644px;" %)AT+JOIN
498 498  |(% style="width:163px" %)**Command Example**|(% style="width:147px" %)**Function**|(% style="width:334px" %)**Response**
... ... @@ -506,12 +506,12 @@
506 506  
507 507  == 6.4 LoRa® Network Join Mode ==
508 508  
573 +
509 509  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
510 510  
511 -{{info}}
512 -**AT Command: AT+NJM**
513 -{{/info}}
514 514  
577 +(% style="color:blue" %)**AT Command: AT+NJM**
578 +
515 515  (% border="1" style="background-color:#ffffcc; color:green; width:753.222px" %)
516 516  |=(% colspan="3" style="width: 750px;" %)AT+NJM
517 517  |(% style="width:162px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:361px" %)**Response**
... ... @@ -521,27 +521,27 @@
521 521  |(% style="width:162px" %)AT+NJM=0|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)OK
522 522  |(% style="width:162px" %)AT+NJM=2|(% style="width:227px" %)Set the Network Join Mode|(% style="width:361px" %)While Error in format, return AT_PARAM_ERROR
523 523  
524 -{{info}}
525 -**Downlink Command: 0x20**
526 -{{/info}}
527 527  
589 +(% style="color:blue" %)**Downlink Command: 0x20**
590 +
528 528  Format: Command Code (0x20) followed by 1 bytes mode value.
529 529  
530 530  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
531 531  
532 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
595 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
533 533  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
534 534  
535 535  
536 536  
600 +
537 537  == 6.5 LoRa® Network Join Status ==
538 538  
603 +
539 539  Feature: LoRa® Network Join Status.
540 540  
541 -{{info}}
542 -**AT Command: AT+NJS**
543 -{{/info}}
544 544  
607 +(% style="color:blue" %)**AT Command: AT+NJS**
608 +
545 545  (% border="1" style="background-color:#ffffcc; color:green; width:498.222px" %)
546 546  |=(% colspan="3" style="width: 495px;" %)AT+NJS
547 547  |(% style="width:169px" %)**Command Example**|(% style="width:164px" %)**Function**|(% style="width:161px" %)**Response**
... ... @@ -553,12 +553,12 @@
553 553  
554 554  == 6.6 Print Last Received Data in Raw Format ==
555 555  
620 +
556 556  Feature: Print Last Received Data in Raw Format<port:data>.
557 557  
558 -{{info}}
559 -**AT Command: AT+RECV**
560 -{{/info}}
561 561  
624 +(% style="color:blue" %)**AT Command: AT+RECV**
625 +
562 562  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
563 563  |=(% colspan="3" style="width: 584px;" %)AT+RECV
564 564  |(% style="width:161px" %)**Command Example**|(% style="width:272px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -570,12 +570,12 @@
570 570  
571 571  == 6.7 Print Last Received Data in Binary Format ==
572 572  
637 +
573 573  Feature: Print Last Received Data in Binary Format<port:data>.
574 574  
575 -{{info}}
576 -**AT Command: AT+RECVB**
577 -{{/info}}
578 578  
641 +(% style="color:blue" %)**AT Command: AT+RECVB**
642 +
579 579  (% border="1" style="background-color:#ffffcc; color:green; width:793.222px" %)
580 580  |=(% colspan="3" style="width: 790px;" %)AT+RECVB
581 581  |(% style="width:173px" %)**Command Example**|(% style="width:497px" %)**Function**|(% style="width:120px" %)**Response**
... ... @@ -587,12 +587,12 @@
587 587  
588 588  == 6.8 Send Text Data ==
589 589  
654 +
590 590  Feature: Send Text Data<port:data>.
591 591  
592 -{{info}}
593 -**AT Command: AT+SEND**
594 -{{/info}}
595 595  
658 +(% style="color:blue" %)**AT Command: AT+SEND**
659 +
596 596  (% border="1" style="background-color:#ffffcc; color:green; width:991.222px" %)
597 597  |=(% colspan="3" style="width: 988px;" %)AT+SEND
598 598  |(% style="width:201px" %)**Command Example**|(% style="width:340px" %)**Function**|(% style="width:446px" %)**Response**
... ... @@ -608,12 +608,12 @@
608 608  
609 609  == 6.9 Send Hexadecimal Data ==
610 610  
675 +
611 611  Feature: Send hexadecimal data along with the application port.
612 612  
613 -{{info}}
614 -**AT Command: AT+SENDB**
615 -{{/info}}
616 616  
679 +(% style="color:blue" %)**AT Command: AT+SENDB**
680 +
617 617  (% border="1" style="background-color:#ffffcc; color:green; width:1120.22px" %)
618 618  |=(% colspan="3" style="width: 1117px;" %)AT+SENDB
619 619  |(% style="width:257px" %)**Command Example**|(% style="width:406px" %)**Function**|(% style="width:453px" %)**Response**
... ... @@ -628,14 +628,15 @@
628 628  
629 629  = 7. LoRaWAN network management =
630 630  
695 +
631 631  == 7.1 Adaptive Data Rate ==
632 632  
698 +
633 633  Feature: Get or Set the Adaptive Data Rate setting. (0: off, 1: on).
634 634  
635 -{{info}}
636 -**AT Command: AT+ADR**
637 -{{/info}}
638 638  
702 +(% style="color:blue" %)**AT Command: AT+ADR**
703 +
639 639  (% border="1" style="background-color:#ffffcc; color:green; width:683.222px" %)
640 640  |=(% colspan="3" style="width: 680px;" %)AT+ADR
641 641  |(% style="width:162px" %)**Command Example**|(% style="width:266px" %)**Function**|(% style="width:250px" %)**Response**
... ... @@ -647,26 +647,25 @@
647 647  AT_PARAM_ERROR
648 648  )))
649 649  
650 -{{info}}
651 -**Downlink Command: 0x22**
652 -{{/info}}
653 653  
716 +(% style="color:blue" %)**Downlink Command: 0x22**
654 654  
655 655  If the downlink payload=2201, it means setting the adaptive data rate to 1, while type code is 22.
656 656  
657 -* **Example 1**: Downlink Payload: **2201** ~/~/ Set AT+ADR=1.
720 +* **Example 1**: Downlink Payload: **2201**  ~/~/ Set AT+ADR=1.
658 658  * **Example 2**: Downlink Payload: **2200FFFF** ~/~/ Set AT+ADR=0.
659 659  
660 660  
661 661  
725 +
662 662  == 7.2 LoRa® Class ==
663 663  
728 +
664 664  Feature: Get or Set the Device Class(Currently only support class A, class C).
665 665  
666 -{{info}}
667 -**AT Command:AT+CLASS**
668 -{{/info}}
669 669  
732 +(% style="color:blue" %)**AT Command:AT+CLASS**
733 +
670 670  (% border="1" style="background-color:#ffffcc; color:green; width:507.222px" %)
671 671  |=(% colspan="3" style="width: 504px;" %)AT+CLASS
672 672  |(% style="width:163px" %)**Command Example**|(% style="width:166px" %)**Function**|(% style="width:175px" %)**Response**
... ... @@ -681,12 +681,12 @@
681 681  
682 682  == 7.3 Duty Cycle Setting ==
683 683  
748 +
684 684  Feature: Get or Set the ETSI Duty Cycle setting - 0=disable, 1=enable - Only for testing.
685 685  
686 -{{info}}
687 -**AT Command:AT+DCS**
688 -{{/info}}
689 689  
752 +(% style="color:blue" %)**AT Command:AT+DCS**
753 +
690 690  (% border="1" style="background-color:#ffffcc; color:green; width:515.222px" %)
691 691  |=(% colspan="3" style="width: 512px;" %)AT+DCS
692 692  |(% style="width:165px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:107px" %)**Response**
... ... @@ -697,14 +697,16 @@
697 697  
698 698  )))
699 699  
764 +
765 +
700 700  == 7.4 Data Rate ==
701 701  
768 +
702 702  Feature: Get or Set the Data Rate. (0-7 corresponding to DR_X) . Note: while set Data Rate, please use set Adptive Data Rate, ADR=0 first. otherwise device will response to server's ADR command and change the DR to the setting from server
703 703  
704 -{{info}}
705 -**AT Command: AT+DR**
706 -{{/info}}
707 707  
772 +(% style="color:blue" %)**AT Command: AT+DR**
773 +
708 708  (% border="1" style="background-color:#ffffcc; color:green; width:466.222px" %)
709 709  |=(% colspan="3" style="width: 463px;" %)AT+DR
710 710  |(% style="width:156px" %)**Command Example**|(% style="width:167px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -715,10 +715,8 @@
715 715  
716 716  )))
717 717  
718 -{{info}}
719 -**Downlink Command: 0x2200aaFF**
720 -{{/info}}
721 721  
785 +(% style="color:blue" %)**Downlink Command: 0x2200aaFF**
722 722  
723 723  If the downlink payload=220001FF, it means setting the data rate to 1, while type code is 22 00 aa FF.
724 724  
... ... @@ -725,14 +725,17 @@
725 725  * **Example 1**: Downlink Payload: **220001FF** ~/~/ Set AT+DR=1.
726 726  * **Example 2**: Downlink Payload: **220000FF** ~/~/ Set AT+DR=0.
727 727  
792 +
793 +
794 +
728 728  == 7.5 Frame Counter Downlink ==
729 729  
797 +
730 730  Feature: Get or Set the Frame Counter Downlink.
731 731  
732 -{{info}}
733 -**AT Command:AT+FCD**
734 -{{/info}}
735 735  
801 +(% style="color:blue" %)**AT Command:AT+FCD**
802 +
736 736  (% border="1" style="background-color:#ffffcc; color:green; width:693.222px" %)
737 737  |=(% colspan="3" style="width: 690px;" %)AT+FCD
738 738  |(% style="width:162px" %)**Command Example**|(% style="width:258px" %)**Function**|(% style="width:269px" %)**Response**
... ... @@ -741,18 +741,18 @@
741 741  )))
742 742  |(% style="width:162px" %)AT+FCD=10|(% style="width:258px" %)Set the Frame Counter Downlink.|(% style="width:269px" %)(System will write new value to FCD)(((
743 743  OK
744 -
745 -
746 746  )))
747 747  
813 +
814 +
748 748  == 7.6 Frame Counter Uplink ==
749 749  
750 750  Feature: Get or Set the Frame Counter Uplink.
751 751  
752 -{{info}}
753 -**AT Command:AT+FCU**
754 -{{/info}}
755 755  
820 +(% style="color:blue" %)**AT Command:AT+FCU**
821 +
822 +
756 756  (% border="1" style="background-color:#ffffcc; color:green; width:534.222px" %)
757 757  |=(% colspan="3" style="width: 531px;" %)AT+FCU
758 758  |(% style="width:177px" %)**Command Example**|(% style="width:239px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -767,10 +767,10 @@
767 767  
768 768  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 1 in ms.
769 769  
770 -{{info}}
771 -**AT Command:AT+JN1DL**
772 -{{/info}}
773 773  
838 +(% style="color:blue" %)**AT Command:AT+JN1DL**
839 +
840 +
774 774  (% border="1" style="background-color:#ffffcc; color:green; width:537.222px" %)
775 775  |=(% colspan="3" style="width: 534px;" %)AT+JN1DL
776 776  |(% style="width:164px" %)**Command Example**|(% style="width:229px" %)**Function**|(% style="width:140px" %)**Response**
... ... @@ -785,10 +785,10 @@
785 785  
786 786  Feature: Get or Set the Join Accept Delay between the end of the Tx and the Join Rx Window 2 in ms.
787 787  
788 -{{info}}
789 -**AT Command:AT+JN2DL**
790 -{{/info}}
791 791  
856 +(% style="color:blue" %)**AT Command:AT+JN2DL**
857 +
858 +
792 792  (% border="1" style="background-color:#ffffcc; color:green; width:538.222px" %)
793 793  |=(% colspan="3" style="width: 535px;" %)AT+JN2DL
794 794  |(% style="width:160px" %)**Command Example**|(% style="width:228px" %)**Function**|(% style="width:146px" %)**Response**
... ... @@ -801,12 +801,14 @@
801 801  
802 802  == 7.9 Public Network Mode ==
803 803  
804 -Feature: Get or Set the public network mode. (0: off, 1: on)
871 +Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
805 805  
806 -{{info}}
807 -**AT Command:AT+PNM**
808 -{{/info}}
873 +Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
809 809  
875 +
876 +(% style="color:blue" %)**AT Command:AT+PNM**
877 +
878 +
810 810  (% border="1" style="background-color:#ffffcc; color:green; width:667.222px" %)
811 811  |=(% colspan="3" style="width: 664px;" %)AT+PNM
812 812  |(% style="width:166px" %)**Command Example**|(% style="width:225px" %)**Function**|(% style="width:272px" %)**Response**
... ... @@ -813,20 +813,25 @@
813 813  |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
814 814  OK
815 815  )))
816 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
885 +|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
886 +Set the public network mode.
887 +
888 +Set syncword=0x34
889 +)))|(% style="width:272px" %)(System will write new value to PNM)(((
817 817  OK
818 818  
819 819  
820 820  )))
894 +|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
821 821  
822 822  == 7.10 Receive Delay1 ==
823 823  
824 824  Feature: Get or Set the delay between the end of the Tx and the Rx Window 1 in ms
825 825  
826 -{{info}}
827 -**AT Command:AT+RX1DL**
828 -{{/info}}
829 829  
901 +(% style="color:blue" %)**AT Command:AT+RX1DL**
902 +
903 +
830 830  (% border="1" style="background-color:#ffffcc; color:green; width:408.222px" %)
831 831  |=(% colspan="3" style="width: 405px;" %)AT+RX1DL
832 832  |(% style="width:155px" %)**Command Example**|(% style="width:128px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -841,10 +841,10 @@
841 841  
842 842  Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
843 843  
844 -{{info}}
845 -**AT Command:AT+RX2DL**
846 -{{/info}}
847 847  
919 +(% style="color:blue" %)**AT Command:AT+RX2DL**
920 +
921 +
848 848  (% border="1" style="background-color:#ffffcc; color:green; width:481.222px" %)
849 849  |=(% colspan="3" style="width: 478px;" %)AT+RX2DL
850 850  |(% style="width:175px" %)**Command Example**|(% style="width:152px" %)**Function**|(% style="width:150px" %)**Response**
... ... @@ -859,10 +859,10 @@
859 859  
860 860  Feature: Get or Set the Rx2 window data rate (0-7 corresponding to DR_X)
861 861  
862 -{{info}}
863 -**AT Command:AT+RX2DR**
864 -{{/info}}
865 865  
937 +(% style="color:blue" %)**AT Command:AT+RX2DR**
938 +
939 +
866 866  (% border="1" style="background-color:#ffffcc; color:green; width:525.222px" %)
867 867  |=(% colspan="3" style="width: 522px;" %)AT+RX2DR
868 868  |(% style="width:160px" %)**Command Example**|(% style="width:232px" %)**Function**|(% style="width:130px" %)**Response**
... ... @@ -877,10 +877,10 @@
877 877  
878 878  Feature: Get or Set the Rx2 window frequency
879 879  
880 -{{info}}
881 -**AT Command:AT+RX2FQ**
882 -{{/info}}
883 883  
955 +(% style="color:blue" %)**AT Command:AT+RX2FQ**
956 +
957 +
884 884  (% border="1" style="background-color:#ffffcc; color:green; width:587.222px" %)
885 885  |=(% colspan="3" style="width: 584px;" %)AT+RX2FQ
886 886  |(% style="width:183px" %)**Command Example**|(% style="width:240px" %)**Function**|(% style="width:160px" %)**Response**
... ... @@ -895,10 +895,10 @@
895 895  
896 896  Feature: Get or Set the Transmit Power(0-5, MAX:0, MIN:5, according to LoRaWAN Spec, or 40=10dB, 41 = 11dB, …, 50 = 20dB which is out of LoRaWAN spec. )
897 897  
898 -{{info}}
899 -**AT Command:AT+TXP**
900 -{{/info}}
901 901  
973 +(% style="color:blue" %)**AT Command:AT+TXP**
974 +
975 +
902 902  (% border="1" style="background-color:#ffffcc; color:green; width:465.222px" %)
903 903  |=(% colspan="3" style="width: 462px;" %)AT+TXP
904 904  |(% style="width:161px" %)**Command Example**|(% style="width:189px" %)**Function**|(% style="width:112px" %)**Response**
... ... @@ -920,10 +920,10 @@
920 920  
921 921  Feature: Get or Set the Rx2 window frequency
922 922  
923 -{{info}}
924 -**AT Command:AT+RSSI**
925 -{{/info}}
926 926  
998 +(% style="color:blue" %)**AT Command:AT+RSSI**
999 +
1000 +
927 927  (% border="1" style="background-color:#ffffcc; color:green; width:557.222px" %)
928 928  |=(% colspan="3" style="width: 554px;" %)AT+RSSI
929 929  |(% style="width:164px" %)**Command Example**|(% style="width:289px" %)**Function**|(% style="width:100px" %)**Response**
... ... @@ -935,10 +935,10 @@
935 935  
936 936  Feature: Get the SNR of the last received packet
937 937  
938 -{{info}}
939 -**AT Command:AT+SNR**
940 -{{/info}}
941 941  
1013 +(% style="color:blue" %)**AT Command:AT+SNR**
1014 +
1015 +
942 942  (% border="1" style="background-color:#ffffcc; color:green; width:571.222px" %)
943 943  |=(% colspan="3" style="width: 568px;" %)AT+SNR
944 944  |(% style="width:164px" %)**Command Example**|(% style="width:290px" %)**Function**|(% style="width:113px" %)**Response**
... ... @@ -950,10 +950,10 @@
950 950  
951 951  Feature: Get or set the application port.
952 952  
953 -{{info}}
954 -**AT Command: AT+PORT**
955 -{{/info}}
956 956  
1028 +(% style="color:blue" %)**AT Command: AT+PORT**
1029 +
1030 +
957 957  (% border="1" style="background-color:#ffffcc; color:green; width:500.222px" %)
958 958  |=(% colspan="3" style="width: 497px;" %)AT+PORT
959 959  |(% style="width:157px" %)**Command Example**|(% style="width:204px" %)**Function**|(% style="width:135px" %)**Response**
... ... @@ -962,10 +962,9 @@
962 962  )))
963 963  |(% style="width:157px" %)AT+PORT=21|(% style="width:204px" %)Set the application port|(% style="width:135px" %)OK
964 964  
965 -{{info}}
966 -**Downlink Command: 0x23**
967 -{{/info}}
1039 +(% style="color:blue" %)**Downlink Command: 0x23**
968 968  
1041 +
969 969  Format: Command Code (0x23) followed by 1 bytes port value.
970 970  
971 971  If the downlink payload=2301, it means set the application port to 1, while type code is 23.
... ... @@ -977,10 +977,10 @@
977 977  
978 978  Feature:Get or Set Frequency (Unit: Hz) for Single Channel Mode.
979 979  
980 -{{info}}
981 -**AT Command: AT+CHS**
982 -{{/info}}
983 983  
1054 +(% style="color:blue" %)**AT Command: AT+CHS**
1055 +
1056 +
984 984  (% border="1" style="background-color:#ffffcc; color:green; width:603.222px" %)
985 985  |=(% colspan="3" style="width: 600px;" %)AT+CHS
986 986  |(% style="width:182px" %)**Command Example**|(% style="width:295px" %)**Function**|(% style="width:122px" %)**Response**
... ... @@ -993,10 +993,10 @@
993 993  
994 994  Feature: Get or Set eight channels mode,Only for US915,AU915,CN470.
995 995  
996 -{{info}}
997 -**AT Command: AT+CHE**
998 -{{/info}}
999 999  
1070 +(% style="color:blue" %)**AT Command: AT+CHE**
1071 +
1072 +
1000 1000  (% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1001 1001  |=(% colspan="3" style="width: 707px;" %)AT+CHE
1002 1002  |(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
... ... @@ -1007,10 +1007,9 @@
1007 1007  )))
1008 1008  |(% style="width:160px" %)AT+CHE=1|(% style="width:198px" %)Set eight channels mode|(% style="width:349px" %)OK
1009 1009  
1010 -{{info}}
1011 -**Downlink Command: 0x24**
1012 -{{/info}}
1083 +(% style="color:blue" %)**Downlink Command: 0x24**
1013 1013  
1085 +
1014 1014  Format: Command Code (0x24) followed by 1 bytes channel value.
1015 1015  
1016 1016  If the downlink payload=2401, it means set channel mode to 1, while type code is 24.
... ... @@ -1022,10 +1022,10 @@
1022 1022  
1023 1023  Feature:Get or Set the number of symbols to detect and timeout from RXwindow1(0 to 255).
1024 1024  
1025 -{{info}}
1026 -**AT Command: AT+RX1WTO**
1027 -{{/info}}
1028 1028  
1098 +(% style="color:blue" %)**AT Command: AT+RX1WTO**
1099 +
1100 +
1029 1029  (% border="1" style="background-color:#ffffcc; color:green; width:460.222px" %)
1030 1030  |=(% colspan="3" style="width: 457px;" %)AT+ RX1WTO
1031 1031  |(% style="width:163px" %)**Command Example**|(% style="width:201px" %)**Function**|(% style="width:93px" %)**Response**
... ... @@ -1050,10 +1050,10 @@
1050 1050  
1051 1051  Feature:Get or Set the number of symbols to detect and timeout from RXwindow2(0 to 255).
1052 1052  
1053 -{{info}}
1054 -**AT Command: AT+RX2WTO**
1055 -{{/info}}
1056 1056  
1126 +(% style="color:blue" %)**AT Command: AT+RX2WTO**
1127 +
1128 +
1057 1057  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1058 1058  |=(% colspan="3" style="width: 494px;" %)AT+ RX2WTO
1059 1059  |(% style="width:190px" %)**Command Example**|(% style="width:199px" %)**Function**|(% style="width:104px" %)**Response**
... ... @@ -1066,10 +1066,10 @@
1066 1066  
1067 1067  Feature: Get or Set uplinkdwelltime
1068 1068  
1069 -{{info}}
1070 -**AT Command: AT+DWELLT**
1071 -{{/info}}
1072 1072  
1142 +(% style="color:blue" %)**AT Command: AT+DWELLT**
1143 +
1144 +
1073 1073  (% border="1" style="background-color:#ffffcc; color:green; width:497.222px" %)
1074 1074  |=(% colspan="3" style="width: 494px;" %)AT+DWELLT
1075 1075  |(% style="width:183px" %)**Command Example**|(% style="width:179px" %)**Function**|(% style="width:131px" %)**Response**
... ... @@ -1078,10 +1078,9 @@
1078 1078  )))
1079 1079  |(% style="width:183px" %)AT+DWELLT=0|(% style="width:179px" %)Set uplinkdwelltime|(% style="width:131px" %)OK
1080 1080  
1081 -{{info}}
1082 -**Downlink Command: 0x25**
1083 -{{/info}}
1153 +(% style="color:blue" %)**Downlink Command: 0x25**
1084 1084  
1155 +
1085 1085  Format: Command Code (0x25) followed by 1 bytes state value.
1086 1086  
1087 1087  If the downlink payload=2501, it means set uplinkdwelltime to 1, while type code is 25.
... ... @@ -1107,10 +1107,9 @@
1107 1107  * For Class C devices used in ChirpStack, need to set AT+RPL=4 because Chirpstack require immedietely reply message to MAC Command.
1108 1108  * For Class C devices used in TTI, need to set AT+RPL=4 because TTI require immediately reply message to Confirmed Data Down & MAC Command.
1109 1109  
1110 -{{info}}
1111 -**AT Command: AT+RPL**
1112 -{{/info}}
1181 +(% style="color:blue" %)**AT Command: AT+RPL**
1113 1113  
1183 +
1114 1114  (% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1115 1115  |=(% colspan="3" style="width: 533px;" %)AT+RPL
1116 1116  |(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
... ... @@ -1119,10 +1119,9 @@
1119 1119  )))
1120 1120  |(% style="width:160px" %)AT+RPL=0|(% style="width:263px" %)Set packet receiving response level|(% style="width:109px" %)OK
1121 1121  
1122 -{{info}}
1123 -**Downlink Command: 0x21**
1124 -{{/info}}
1192 +(% style="color:blue" %)**Downlink Command: 0x21**
1125 1125  
1194 +
1126 1126  Format: Command Code (0x21) followed by 1 bytes level value.
1127 1127  
1128 1128  If the downlink payload=2101, it means set packet receiving response level to 1, while type code is 21.
... ... @@ -1130,6 +1130,126 @@
1130 1130  * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1131 1131  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1132 1132  
1202 +== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1203 +
1204 +
1205 +(% style="color:blue" %)**AT Command: AT+SETMAXNBTRANS **
1206 +
1207 +
1208 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1209 +|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1210 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1211 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1212 +OK
1213 +)))
1214 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1215 +1
1216 +
1217 +OK
1218 +)))
1219 +
1220 +(% style="color:blue" %)**Downlink Command: 0x33**
1221 +
1222 +
1223 +Format: Command Code (0x33) followed by 2 bytes mode value.
1224 +
1225 +If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1226 +
1227 +* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1228 +* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1229 +
1230 +== 7.25 Device offline rejoining （LWS007) ==
1231 +
1232 +
1233 +(% style="color:blue" %)**AT Command: AT+DDETECT**
1234 +
1235 +
1236 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1237 +|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1238 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1239 +|(% style="width:160px" %)(((
1240 +AT+DDETECT=1,1440,2880
1241 +
1242 +value1
1243 +)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1244 +1
1245 +
1246 +OK
1247 +)))
1248 +|(% style="width:160px" %)(((
1249 +AT+DDETECT=1,?,2880
1250 +
1251 +value2
1252 +)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1253 +
1254 +
1255 +OK
1256 +)))
1257 +|(% style="width:160px" %)(((
1258 +AT+DDETECT=1,1440,？
1259 +
1260 +value3
1261 +)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1262 +
1263 +
1264 +OK
1265 +)))
1266 +
1267 +(% style="color:blue" %)**Downlink Command: 0x33**
1268 +
1269 +
1270 +Format: Command Code (0x32) followed by 2 bytes mode value.
1271 +
1272 +If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1273 +
1274 +* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1275 +
1276 +== 7.26 Request the server to send an ACK ==
1277 +
1278 +
1279 +(% style="color:blue" %)**AT Command: AT+PNACKMD**
1280 +
1281 +
1282 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1283 +|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1284 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1285 +|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1286 +OK
1287 +)))
1288 +|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1289 +0
1290 +
1291 +OK
1292 +)))
1293 +
1294 +== 7.27 Adjust network rejoining interval ==
1295 +
1296 +
1297 +(% style="color:blue" %)**AT Command: AT+RJTDC**
1298 +
1299 +
1300 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1301 +|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1302 +|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1303 +|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30000(((
1304 +OK
1305 +
1306 +the interval is 30000ms = 30s
1307 +)))
1308 +|(% style="width:165px" %)AT+RJTDC=60000|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1309 +Set the ReJoin data transmission interval to 60000ms = 60 seconds
1310 +)))
1311 +
1312 +(% style="color:blue" %)**Downlink Command: 0x26**
1313 +
1314 +
1315 +Format: Command Code (0x26) followed by 2 bytes mode value.
1316 +
1317 +If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1318 +
1319 +* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1320 +* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1321 +
1133 1133  = 8. AT Commands Combination =
1134 1134  
1135 1135  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1139,10 +1139,10 @@
1139 1139  
1140 1140  == 8.2 Use Downlink Command to set a fix uplink DR ==
1141 1141  
1142 -{{info}}
1143 -**Downlink Command: 0x22000500**
1144 -{{/info}}
1145 1145  
1332 +(% style="color:blue" %)**Downlink Command: 0x22000500**
1333 +
1334 +
1146 1146  Same as:
1147 1147  
1148 1148  * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]

Applications

Navigation

Copyright ©2010-2022 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0