Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,8 +20,8 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
	22	+** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25	25	** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
26	26
27	27
...	...	@@ -100,7 +100,6 @@
100	100	)))
101	101
102	102
103		-
104	104	= 4. System Management Commands =
105	105
106	106	== 4.1 Change Uplink Interval ==
...	...	@@ -360,8 +360,6 @@
360	360	OK
361	361	)))
362	362
363		-
364		-
365	365	== 5.4 Device Address ==
366	366
367	367	Feature: Get or Set the Device Address.
...	...	@@ -380,8 +380,6 @@
380	380	)))
381	381	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
382	382
383		-
384		-
385	385	== 5.5 Device EUI ==
386	386
387	387	Feature: Get or Set the Device EUI.
...	...	@@ -400,8 +400,6 @@
400	400	OK
401	401	)))
402	402
403		-
404		-
405	405	== 5.6 Network ID ==
406	406
407	407	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -811,7 +811,7 @@
811	811
812	812	)))
813	813
814		-== 7.11 Receive Delay2 ==
	806	+== 7.11Receive Delay2 ==
815	815
816	816	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
817	817
...	...	@@ -1016,8 +1016,6 @@
1016	1016
1017	1017	(((
1018	1018	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1019		-
1020		-
1021	1021	)))
1022	1022
1023	1023	== 7.21 Get or Set RXwindows2 timeout ==