Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,12 +20,10 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27		-
28		-
29	29	= 3. Support End Node and firmware version =
30	30
31	31	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -99,8 +99,6 @@
99	99	)))
100	100	)))
101	101
102		-
103		-
104	104	= 4. System Management Commands =
105	105
106	106	== 4.1 Change Uplink Interval ==
...	...	@@ -139,8 +139,6 @@
139	139	* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
140	140	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
141	141
142		-
143		-
144	144	== 4.2 Reboot End Node ==
145	145
146	146	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -176,8 +176,6 @@
176	176
177	177	(((
178	178	If the downlink payload=**04FF**, the end node will reboot.
179		-
180		-
181	181	)))
182	182
183	183	== 4.3 Reset to factory Default ==
...	...	@@ -799,7 +799,7 @@
799	799
800	800	)))
801	801
802		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
803	803
804	804	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
805	805
...	...	@@ -1004,8 +1004,6 @@
1004	1004
1005	1005	(((
1006	1006	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1007		-
1008		-
1009	1009	)))
1010	1010
1011	1011	== 7.21 Get or Set RXwindows2 timeout ==