Last modified by kai on 2024/09/06 10:00
<
From version < 38.103 >
edited by Xiaoling
on 2022/06/01 11:53
To version < 50.4 >
edited by Xiaoling
on 2022/07/13 11:50
>
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,4 @@
1 - **Contents：**
1 + **Table of** **Contents：**
2 2  
3 3  {{toc/}}
4 4  
... ... @@ -6,6 +6,7 @@
6 6  
7 7  = 1. Introduction =
8 8  
9 +
9 9  Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
10 10  
11 11  * **Common Commands:** They should be available for each sensor, such as: change uplink interval, reset device.
... ... @@ -18,6 +18,7 @@
18 18  
19 19  = 2. How to use AT Commands or Downlink command =
20 20  
22 +
21 21  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22 22  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23 23  ** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
... ... @@ -28,6 +28,7 @@
28 28  
29 29  = 3. Support End Node and firmware version =
30 30  
33 +
31 31  (% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
32 32  |=(% colspan="3" style="width: 963px;" %)(((
33 33  Dragino STM32 base hardware Firmware / LoRaWAN stack list
... ... @@ -103,8 +103,10 @@
103 103  
104 104  = 4. System Management Commands =
105 105  
109 +
106 106  == 4.1 Change Uplink Interval ==
107 107  
112 +
108 108  Feature: Change LoRaWAN End Node Transmit Interval.
109 109  
110 110  (% class="box infomessage" %)
... ... @@ -139,6 +139,8 @@
139 139  * **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
140 140  * **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
141 141  
147 +
148 +
142 142  == 4.2 Reboot End Node ==
143 143  
144 144  Feature: Reboot End Node to perform a new OTAA or ABP Join.
... ... @@ -424,6 +424,8 @@
424 424  
425 425  == 6.1 Confirm Mode ==
426 426  
434 +=== AT+CFM command before DR-LWS007 software stack ===
435 +
427 427  Feature: Get or Set the confirmation mode (0-1).
428 428  
429 429  {{info}}
... ... @@ -448,6 +448,54 @@
448 448  * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
449 449  * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
450 450  
460 +=== AT+CFM command since DR-LWS007 software stack ===
461 +
462 +{{info}}
463 +**AT Command: AT+CFM**
464 +{{/info}}
465 +
466 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
467 +|=(% colspan="3" style="width: 707px;" %)AT+CFM
468 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
469 +|(% style="width:160px" %)(((
470 +AT+CFM=1,0,0
471 +
472 +value1
473 +)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
474 +1
475 +
476 +OK
477 +)))
478 +|(% style="width:160px" %)(((
479 +AT+CFM=0,?,0
480 +
481 +value2
482 +)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
483 +0~~7
484 +
485 +OK
486 +)))
487 +|(% style="width:160px" %)(((
488 +AT+CFM=0,0,1
489 +
490 +value3
491 +)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
492 +1
493 +
494 +OK
495 +)))
496 +
497 +{{info}}
498 +**Downlink Command: 0x05**
499 +{{/info}}
500 +
501 +Format: Command Code (0x05) followed by 2 bytes mode value.
502 +
503 +If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
504 +
505 +* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
506 +* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
507 +
451 451  == 6.2 Confirm Status ==
452 452  
453 453  Feature: Get confirmation status of the last AT+SEND (0-1).
... ... @@ -505,7 +505,7 @@
505 505  
506 506  If the downlink payload=2000, it means set the Network Join Mode, while type code is 20.
507 507  
508 -* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
565 +* **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=0
509 509  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
510 510  
511 511  == 6.5 LoRa® Network Join Status ==
... ... @@ -761,8 +761,10 @@
761 761  
762 762  == 7.9 Public Network Mode ==
763 763  
764 -Feature: Get or Set the public network mode. (0: off, 1: on)
821 +Feature: Get or Set the public network mode. (0: off, 1: on). A Public LoRaWAN network use 0x34 as syncword. Default Settings; PNM=1
765 765  
823 +Notice: If user build their own LoRaWAN server but still use syncword=0x34, this is still considered a public LoRaWAN network
824 +
766 766  {{info}}
767 767  **AT Command:AT+PNM**
768 768  {{/info}}
... ... @@ -773,11 +773,16 @@
773 773  |(% style="width:166px" %)AT+PNM=?|(% style="width:225px" %)Get the public network mode.|(% style="width:272px" %)1(((
774 774  OK
775 775  )))
776 -|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)Set the public network mode.|(% style="width:272px" %)(System will write new value to PNM)(((
835 +|(% style="width:166px" %)AT+PNM=1|(% style="width:225px" %)(((
836 +Set the public network mode.
837 +
838 +Set syncword=0x34
839 +)))|(% style="width:272px" %)(System will write new value to PNM)(((
777 777  OK
778 778  
779 779  
780 780  )))
844 +|(% style="width:166px" %)AT+PNM=0|(% style="width:225px" %)Set to use private network autoset syncword=0x12|(% style="width:272px" %)
781 781  
782 782  == 7.10 Receive Delay1 ==
783 783  
... ... @@ -1090,6 +1090,129 @@
1090 1090  * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
1091 1091  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
1092 1092  
1157 +== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
1158 +
1159 +{{info}}
1160 +**AT Command: AT+SETMAXNBTRANS **
1161 +{{/info}}
1162 +
1163 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1164 +|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
1165 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1166 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
1167 +OK
1168 +)))
1169 +|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2: 0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
1170 +1
1171 +
1172 +OK
1173 +)))
1174 +
1175 +{{info}}
1176 +**Downlink Command: 0x33**
1177 +{{/info}}
1178 +
1179 +Format: Command Code (0x33) followed by 2 bytes mode value.
1180 +
1181 +If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
1182 +
1183 +* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
1184 +* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
1185 +
1186 +== 7.25 Device offline rejoining （LWS007) ==
1187 +
1188 +{{info}}
1189 +**AT Command: AT+DDETECT**
1190 +{{/info}}
1191 +
1192 +(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
1193 +|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
1194 +|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
1195 +|(% style="width:160px" %)(((
1196 +AT+DDETECT=1,1440,2880
1197 +
1198 +value1
1199 +)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
1200 +1
1201 +
1202 +OK
1203 +)))
1204 +|(% style="width:160px" %)(((
1205 +AT+DDETECT=1,?,2880
1206 +
1207 +value2
1208 +)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
1209 +
1210 +
1211 +OK
1212 +)))
1213 +|(% style="width:160px" %)(((
1214 +AT+DDETECT=1,1440,？
1215 +
1216 +value3
1217 +)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
1218 +
1219 +
1220 +OK
1221 +)))
1222 +
1223 +{{info}}
1224 +**Downlink Command: 0x33**
1225 +{{/info}}
1226 +
1227 +Format: Command Code (0x32) followed by 2 bytes mode value.
1228 +
1229 +If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
1230 +
1231 +* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
1232 +
1233 +== 7.26 Request the server to send an ACK ==
1234 +
1235 +{{info}}
1236 +**AT Command: AT+PNACKMD**
1237 +{{/info}}
1238 +
1239 +(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
1240 +|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
1241 +|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
1242 +|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
1243 +OK
1244 +)))
1245 +|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
1246 +0
1247 +
1248 +OK
1249 +)))
1250 +
1251 +== 7.27 Adjust network rejoining interval ==
1252 +
1253 +{{info}}
1254 +**AT Command: AT+RJTDC**
1255 +{{/info}}
1256 +
1257 +(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
1258 +|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
1259 +|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
1260 +|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30000(((
1261 +OK
1262 +
1263 +the interval is 30000ms = 30s
1264 +)))
1265 +|(% style="width:165px" %)AT+RJTDC=60000|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
1266 +Set the ReJoin data transmission interval to 60000ms = 60 seconds
1267 +)))
1268 +
1269 +{{info}}
1270 +**Downlink Command: 0x26**
1271 +{{/info}}
1272 +
1273 +Format: Command Code (0x26) followed by 2 bytes mode value.
1274 +
1275 +If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
1276 +
1277 +* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
1278 +* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
1279 +
1093 1093  = 8. AT Commands Combination =
1094 1094  
1095 1095  == 8.1 Set a fix RX2DR for downlink window ==
... ... @@ -1108,3 +1108,4 @@
1108 1108  * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1109 1109  * AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1110 1110  * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
1298 +~)~)~)

Applications

Navigation

Copyright ©2010-2024 Dragino Technology Co., LTD. All rights reserved
Dragino Wiki v2.0