Changes for page End Device AT Commands and Downlink Command
Last modified by kai on 2024/09/06 10:00
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -3,7 +3,6 @@ 3 3 {{toc/}} 4 4 5 5 6 - 7 7 = 1. Introduction = 8 8 9 9 Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands: ... ... @@ -20,12 +20,10 @@ 20 20 21 21 * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]] 22 22 * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command: 23 -** Use HEX format to send a downlink: [[TTN v3>>Notes 24 -** Use Base64 format to send a downlink: [[Chirpstack>>Notes 25 -** See use note for more serves [[Servers Note>>doc :Main.WebHome]](IoT LoRaWANServer)22 +** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]] 23 +** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]]. 24 +** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]] 26 26 27 - 28 - 29 29 = 3. Support End Node and firmware version = 30 30 31 31 (% border="1" style="background-color:#ffffcc; color:green; width:966px" %) ... ... @@ -99,8 +99,6 @@ 99 99 ))) 100 100 ))) 101 101 102 - 103 - 104 104 = 4. System Management Commands = 105 105 106 106 == 4.1 Change Uplink Interval == ... ... @@ -174,8 +174,6 @@ 174 174 175 175 ((( 176 176 If the downlink payload=**04FF**, the end node will reboot. 177 - 178 - 179 179 ))) 180 180 181 181 == 4.3 Reset to factory Default == ... ... @@ -797,7 +797,7 @@ 797 797 798 798 ))) 799 799 800 -== 7.11 793 +== 7.11Receive Delay2 == 801 801 802 802 Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms 803 803 ... ... @@ -1002,8 +1002,6 @@ 1002 1002 1003 1003 ((( 1004 1004 Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink. 1005 - 1006 - 1007 1007 ))) 1008 1008 1009 1009 == 7.21 Get or Set RXwindows2 timeout == ... ... @@ -1097,6 +1097,7 @@ 1097 1097 * **AT+ADR=0 **~-~-> Disable ADR first 1098 1098 * **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate 1099 1099 1091 + 1100 1100 == 8.2 Use Downlink Command to set a fix uplink DR == 1101 1101 1102 1102 {{info}} ... ... @@ -1105,6 +1105,6 @@ 1105 1105 1106 1106 Same as: 1107 1107 1108 -* AT+ADR=0 1109 -* AT+DR=5 1110 -* AT+TXP=0 1100 +* AT+ADR=0 [[Reference>>||anchor="H7.1AdaptiveDataRate"]] 1101 +* AT+DR=5 [[Reference>>||anchor="H7.4DataRate"]] 1102 +* AT+TXP=0 [[Reference>>||anchor="H7.14TransmitPower"]]