Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,12 +20,10 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27		-
28		-
29	29	= 3. Support End Node and firmware version =
30	30
31	31	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -172,8 +172,6 @@
172	172
173	173	(((
174	174	If the downlink payload=**04FF**, the end node will reboot.
175		-
176		-
177	177	)))
178	178
179	179	== 4.3 Reset to factory Default ==
...	...	@@ -795,7 +795,7 @@
795	795
796	796	)))
797	797
798		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
799	799
800	800	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
801	801
...	...	@@ -996,12 +996,10 @@
996	996	**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
997	997	)))
998	998
999		-[[image:image-20220526162535-1.png]]
	994	+[[image:image-20220511120050-1.png]]
1000	1000
1001	1001	(((
1002	1002	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1003		-
1004		-
1005	1005	)))
1006	1006
1007	1007	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1103,6 +1103,6 @@
1103	1103
1104	1104	Same as:
1105	1105
1106		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1107		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1108		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1099	+* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.1AdaptiveDataRate]]
	1100	+* AT+DR=5 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
	1101	+* AT+TXP=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]