Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -170,8 +170,6 @@
170	170
171	171	(((
172	172	If the downlink payload=**04FF**, the end node will reboot.
173		-
174		-
175	175	)))
176	176
177	177	== 4.3 Reset to factory Default ==
...	...	@@ -296,7 +296,6 @@
296	296	OK
297	297	)))
298	298
299		-
300	300	= 5. Keys, IDs and EUIs management =
301	301
302	302	== 5.1 Application EUI ==
...	...	@@ -315,7 +315,6 @@
315	315	)))
316	316	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
317	317
318		-
319	319	== 5.2 Application Key ==
320	320
321	321	Feature: Get or Set the Application Key.
...	...	@@ -332,7 +332,6 @@
332	332	)))
333	333	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
334	334
335		-
336	336	== 5.3 Application Session Key ==
337	337
338	338	Feature: Get or Set the Application Session Key.
...	...	@@ -351,7 +351,6 @@
351	351	OK
352	352	)))
353	353
354		-
355	355	== 5.4 Device Address ==
356	356
357	357	Feature: Get or Set the Device Address.
...	...	@@ -370,8 +370,6 @@
370	370	)))
371	371	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
372	372
373		-
374		-
375	375	== 5.5 Device EUI ==
376	376
377	377	Feature: Get or Set the Device EUI.
...	...	@@ -390,8 +390,6 @@
390	390	OK
391	391	)))
392	392
393		-
394		-
395	395	== 5.6 Network ID ==
396	396
397	397	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -801,7 +801,7 @@
801	801
802	802	)))
803	803
804		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
805	805
806	806	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
807	807
...	...	@@ -1006,8 +1006,6 @@
1006	1006
1007	1007	(((
1008	1008	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1009		-
1010		-
1011	1011	)))
1012	1012
1013	1013	== 7.21 Get or Set RXwindows2 timeout ==