Changes for page End Device AT Commands and Downlink Command

Last modified by kai on 2024/09/06 10:00

From version < 33.1 >

edited by Xiaoling
on 2022/05/27 18:02

To version < 47.1 >

edited by Bei Jinggeng
on 2022/06/13 14:45

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Xiaoling
++XWiki.Bei

Content

@@ -20,8 +20,8 @@
  * For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
  * For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
--** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
--** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
++** Use HEX format to send a downlink: [[TTN v3>>Notes for TTN]]
++** Use Base64 format to send a downlink: [[Chirpstack>>Notes for ChirpStack]]
  ** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
  = 3. Support End Node and firmware version =
@@ -296,8 +296,6 @@
  OK
  )))
--
--
  = 5. Keys, IDs and EUIs management =
  == 5.1 Application EUI ==
@@ -316,8 +316,6 @@
  )))
  |(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
--
--
  == 5.2 Application Key ==
  Feature: Get or Set the Application Key.
@@ -334,8 +334,6 @@
  )))
  |(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
--
--
  == 5.3 Application Session Key ==
  Feature: Get or Set the Application Session Key.
@@ -354,8 +354,6 @@
  OK
  )))
--
--
  == 5.4 Device Address ==
  Feature: Get or Set the Device Address.
@@ -428,6 +428,8 @@
  == 6.1 Confirm Mode ==
++=== AT+CFM command before DR-LWS007 software stack ===
++
  Feature: Get or Set the confirmation mode (0-1).
  {{info}}
@@ -452,7 +452,54 @@
  * Example 1: Downlink Payload: 0501 ~/~/ Set AT+CFM=1
  * Example 2: Downlink Payload: 0500 ~/~/ Set AT+CFM=0
++=== AT+CFM command since DR-LWS007 software stack ===
++{{info}}
++**AT Command: AT+CFM**
++{{/info}}
++
++(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
++|=(% colspan="3" style="width: 707px;" %)AT+CFM
++|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
++|(% style="width:160px" %)(((
++AT+CFM=1,0,0
++
++value1
++)))|(% style="width:198px" %)confirmed uplink|(% style="width:349px" %)(((
++1
++
++OK
++)))
++|(% style="width:160px" %)(((
++AT+CFM=0,?,0
++
++value2
++)))|(% style="width:198px" %)set max retry , range: 0 ~~ 7|(% style="width:349px" %)(((
++0~~7
++
++OK
++)))
++|(% style="width:160px" %)(((
++AT+CFM=0,0,1
++
++value3
++)))|(% style="width:198px" %)uplink fcnt increase by 1 for each retry|(% style="width:349px" %)(((
++1
++
++OK
++)))
++
++{{info}}
++**Downlink Command: 0x05**
++{{/info}}
++
++Format: Command Code (0x05) followed by 2 bytes mode value.
++
++If the downlink payload=05010101, it means set end node to use confirm mode, while type code is 05.
++
++* Example 1: Downlink Payload: 05010101 ~/~/ Set AT+CFM=1,1,1
++* Example 2: Downlink Payload: 05000700 ~/~/ Set AT+CFM=0,7,0
++
  == 6.2 Confirm Status ==
  Feature: Get confirmation status of the last AT+SEND (0-1).
@@ -468,7 +468,6 @@
  OK
  )))
--
  == 6.3 Join LoRa® Network ==
  Feature: Join network.
@@ -486,7 +486,6 @@
  While Error in format, return AT_BUSY_ERROR
  )))
--
  == 6.4 LoRa® Network Join Mode ==
  Feature: Get or Set the Network Join Mode. (0: ABP, 1: OTAA).
@@ -515,7 +515,6 @@
  * **Example 1: **Downlink Payload: **2000** ~/~/ Set AT+NJM=O
  * **Example 2:** Downlink Payload: **2001** ~/~/ Set AT+NJM=1
--
  == 6.5 LoRa® Network Join Status ==
  Feature: LoRa® Network Join Status.
@@ -531,7 +531,6 @@
  OK
  )))
--
  == 6.6 Print Last Received Data in Raw Format ==
  Feature: Print Last Received Data in Raw Format<port:data>.
@@ -547,7 +547,6 @@
  OK
  )))
--
  == 6.7 Print Last Received Data in Binary Format ==
  Feature: Print Last Received Data in Binary Format<port:data>.
@@ -563,7 +563,6 @@
  OK
  )))
--
  == 6.8 Send Text Data ==
  Feature: Send Text Data<port:data>.
@@ -583,7 +583,6 @@
  )))
--
  == 6.9 Send Hexadecimal Data ==
  Feature: Send hexadecimal data along with the application port.
@@ -1102,6 +1102,131 @@
  * **Example 1**: Downlink Payload: **2101** ~/~/ set packet receiving response level to 1
  * **Example 2**: Downlink Payload: **2102** ~/~/ set packet receiving response level to 2
++== 7.24 Controls NBTrans in unconfirmed uplink mode（LWS007 NBTrans:Set retransmission packets) ==
++
++{{info}}
++**AT Command: AT+SETMAXNBTRANS **
++{{/info}}
++
++(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
++|=(% colspan="3" style="width: 533px;" %)AT+**SETMAXNBTRANS**
++|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
++|(% style="width:160px" %)**AT+SETMAXNBTRANS=1，0**|(% style="width:263px" %)Value1: set the maximum NBTrans.|(% style="width:109px" %)1(((
++OK
++)))
++|(% style="width:160px" %)**AT+SETMAXNBTRANS=？，1**|(% style="width:263px" %)value2:  0: uplink fcnt doesn't change for each NBTrans; 1: uplink fcnt increase by 1 for each NBTrans.|(% style="width:109px" %)(((
++1
++
++OK
++)))
++
++{{info}}
++**Downlink Command: 0x33**
++{{/info}}
++
++Format: Command Code (0x33) followed by 2 bytes mode value.
++
++If the downlink payload=330100, it means set end node to use confirm mode, while type code is 33.
++
++* Example 1: Downlink Payload: 330100 ~/~/ Set AT+SETMAXNBTRANS=1,0
++* Example 2: Downlink Payload: 330201 ~/~/ Set AT+SETMAXNBTRANS=2,1
++
++== 7.25 Device offline rejoining （LWS007) ==
++
++{{info}}
++**AT Command: AT+DDETECT**
++{{/info}}
++
++(% border="1" style="background-color:#ffffcc; color:green; width:710.222px" %)
++|=(% colspan="3" style="width: 707px;" %)AT+**DDETECT**
++|(% style="width:160px" %)**Command Example**|(% style="width:198px" %)**Function**|(% style="width:349px" %)**Response**
++|(% style="width:160px" %)(((
++AT+DDETECT=1,1440,2880
++
++value1
++)))|(% style="width:198px" %)Enable online detect|(% style="width:349px" %)(((
++1
++
++OK
++)))
++|(% style="width:160px" %)(((
++AT+DDETECT=1,?,2880
++
++value2
++)))|(% style="width:198px" %)Online detection packet sending time|(% style="width:349px" %)(((
++
++
++OK
++)))
++|(% style="width:160px" %)(((
++AT+DDETECT=1,1440,？
++
++value3
++)))|(% style="width:198px" %)Process rejoin|(% style="width:349px" %)(((
++
++
++OK
++)))
++
++{{info}}
++**Downlink Command: 0x33**
++{{/info}}
++
++Format: Command Code (0x32) followed by 2 bytes mode value.
++
++If the downlink payload=320105A00B40, it means set end node to use confirm mode, while type code is 33.
++
++* Example 1: Downlink Payload: 320105A00B40 ~/~/ Set AT+DDETECT=1,1440,2880
++
++== 7.26 Request the server to send an ACK ==
++
++{{info}}
++**AT Command: AT+PNACKMD**
++{{/info}}
++
++(% border="1" style="background-color:#ffffcc; color:green; width:536.222px" %)
++|=(% colspan="3" style="width: 533px;" %)**AT+PNACKMD**
++|(% style="width:160px" %)**Command Example**|(% style="width:263px" %)**Function**|(% style="width:109px" %)**Response**
++|(% style="width:160px" %)**AT+PNACKMD=1**|(% style="width:263px" %)If the node uploads the ACK as confirm, it will request the server to send an ACK. If the server ack is not received, the node will upload the packets that have not received the ACK the next time it receives the ACK|(% style="width:109px" %)1(((
++OK
++)))
++|(% style="width:160px" %)**AT+PNACKMD=0**|(% style="width:263px" %)off request the server to send an ACK|(% style="width:109px" %)(((
++0
++
++OK
++)))
++
++(% class="wikigeneratedid" %)
++== 7.27 Adjust network rejoining interval ==
++
++{{info}}
++**AT Command: AT+RJTDC**
++{{/info}}
++
++(% border="1" style="background-color:#ffffcc; color:green; width:727.222px" %)
++|=(% colspan="3" style="width: 724px;" %)AT+RJTDC
++|(% style="width:165px" %)**Command Example**|(% style="width:227px" %)**Function**|(% style="width:329px" %)**Response**
++|(% style="width:165px" %)AT+RJTDC=?|(% style="width:227px" %)Show the ReJoin data transmission interval in min|(% style="width:329px" %)30000(((
++OK
++
++the interval is 30000ms = 30s
++)))
++|(% style="width:165px" %)AT+RJTDC=60000|(% style="width:227px" %)Set the ReJoin data transmission interval in min|(% style="width:329px" %)OK(((
++Set the ReJoin data transmission interval to 60000ms = 60 seconds
++)))
++
++{{info}}
++**Downlink Command: 0x26**
++{{/info}}
++
++Format: Command Code (0x26) followed by 2 bytes mode value.
++
++If the downlink payload=26000A, it means set end node to use confirm mode, while type code is 26.
++
++* Example 1: Downlink Payload: 26000A ~/~/ Set AT+RJTDC=10
++* Example 2: Downlink Payload: 260002 ~/~/ Set AT+RJTDC=2
++
++
  = 8. AT Commands Combination =
  == 8.1 Set a fix RX2DR for downlink window ==
@@ -1120,3 +1120,4 @@
  * AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
  * AT+DR=5    [[Reference>>||anchor="H7.4DataRate"]]
  * AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
++~)~)~)

Changes for page End Device AT Commands and Downlink Command

Summary

Details

Applications

Navigation