Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -170,8 +170,6 @@
170	170
171	171	(((
172	172	If the downlink payload=**04FF**, the end node will reboot.
173		-
174		-
175	175	)))
176	176
177	177	== 4.3 Reset to factory Default ==
...	...	@@ -384,7 +384,6 @@
384	384	OK
385	385	)))
386	386
387		-
388	388	== 5.6 Network ID ==
389	389
390	390	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -401,7 +401,6 @@
401	401	)))
402	402	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
403	403
404		-
405	405	== 5.7 Network Session Key ==
406	406
407	407	Feature: Get or Set the Network Session Key
...	...	@@ -418,8 +418,6 @@
418	418	)))
419	419	|(% style="width:455px" %)AT+NWKSKEY=A8 40 41 FF FF 12 34 56 00 01 02 04 05 06 06 07|(% style="width:215px" %)Set the Network Session Key.|(% style="width:343px" %)OK
420	420
421		-
422		-
423	423	= 6. Joining and sending date on LoRaWAN network =
424	424
425	425	== 6.1 Confirm Mode ==
...	...	@@ -797,7 +797,7 @@
797	797
798	798	)))
799	799
800		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
801	801
802	802	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
803	803
...	...	@@ -1002,8 +1002,6 @@
1002	1002
1003	1003	(((
1004	1004	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1005		-
1006		-
1007	1007	)))
1008	1008
1009	1009	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1105,6 +1105,6 @@
1105	1105
1106	1106	Same as:
1107	1107
1108		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1109		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1110		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1099	+* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.1AdaptiveDataRate]]
	1100	+* AT+DR=5 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
	1101	+* AT+TXP=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]