Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -170,8 +170,6 @@
170	170
171	171	(((
172	172	If the downlink payload=**04FF**, the end node will reboot.
173		-
174		-
175	175	)))
176	176
177	177	== 4.3 Reset to factory Default ==
...	...	@@ -366,7 +366,6 @@
366	366	)))
367	367	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
368	368
369		-
370	370	== 5.5 Device EUI ==
371	371
372	372	Feature: Get or Set the Device EUI.
...	...	@@ -385,8 +385,6 @@
385	385	OK
386	386	)))
387	387
388		-
389		-
390	390	== 5.6 Network ID ==
391	391
392	392	Feature: Get or Set the Network ID.(You can enter this command change only after successful network connection)
...	...	@@ -403,8 +403,6 @@
403	403	)))
404	404	|(% style="width:191px" %)AT+NWKID=A8 40 41 FF|(% style="width:153px" %)Set the Network ID.|(% style="width:101px" %)OK
405	405
406		-
407		-
408	408	== 5.7 Network Session Key ==
409	409
410	410	Feature: Get or Set the Network Session Key
...	...	@@ -798,7 +798,7 @@
798	798
799	799	)))
800	800
801		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
802	802
803	803	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
804	804
...	...	@@ -1003,8 +1003,6 @@
1003	1003
1004	1004	(((
1005	1005	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1006		-
1007		-
1008	1008	)))
1009	1009
1010	1010	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1098,6 +1098,7 @@
1098	1098	* **AT+ADR=0 **~-~-> Disable ADR first
1099	1099	* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1100	1100
	1091	+
1101	1101	== 8.2 Use Downlink Command to set a fix uplink DR ==
1102	1102
1103	1103	{{info}}
...	...	@@ -1106,6 +1106,6 @@
1106	1106
1107	1107	Same as:
1108	1108
1109		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1110		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1111		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1100	+* AT+ADR=0 [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
	1101	+* AT+DR=5 [[Reference>>||anchor="H7.4DataRate"]]
	1102	+* AT+TXP=0 [[Reference>>||anchor="H7.14TransmitPower"]]