Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -170,8 +170,6 @@
170	170
171	171	(((
172	172	If the downlink payload=**04FF**, the end node will reboot.
173		-
174		-
175	175	)))
176	176
177	177	== 4.3 Reset to factory Default ==
...	...	@@ -348,7 +348,6 @@
348	348	OK
349	349	)))
350	350
351		-
352	352	== 5.4 Device Address ==
353	353
354	354	Feature: Get or Set the Device Address.
...	...	@@ -367,8 +367,6 @@
367	367	)))
368	368	|(% style="width:192px" %)AT+DADDR=A8 40 41 FF|(% style="width:241px" %)Set the Application Session Key.|(% style="width:359px" %)OK
369	369
370		-
371		-
372	372	== 5.5 Device EUI ==
373	373
374	374	Feature: Get or Set the Device EUI.
...	...	@@ -796,7 +796,7 @@
796	796
797	797	)))
798	798
799		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
800	800
801	801	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
802	802
...	...	@@ -1001,8 +1001,6 @@
1001	1001
1002	1002	(((
1003	1003	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1004		-
1005		-
1006	1006	)))
1007	1007
1008	1008	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1096,6 +1096,7 @@
1096	1096	* **AT+ADR=0 **~-~-> Disable ADR first
1097	1097	* **AT+RX2DR=xxxx** ~-~-> Set xxxx to your wanted DataRate
1098	1098
	1091	+
1099	1099	== 8.2 Use Downlink Command to set a fix uplink DR ==
1100	1100
1101	1101	{{info}}
...	...	@@ -1104,6 +1104,6 @@
1104	1104
1105	1105	Same as:
1106	1106
1107		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1108		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1109		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1100	+* AT+ADR=0 [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
	1101	+* AT+DR=5 [[Reference>>||anchor="H7.4DataRate"]]
	1102	+* AT+TXP=0 [[Reference>>||anchor="H7.14TransmitPower"]]