Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -170,8 +170,6 @@
170	170
171	171	(((
172	172	If the downlink payload=**04FF**, the end node will reboot.
173		-
174		-
175	175	)))
176	176
177	177	== 4.3 Reset to factory Default ==
...	...	@@ -296,7 +296,6 @@
296	296	OK
297	297	)))
298	298
299		-
300	300	= 5. Keys, IDs and EUIs management =
301	301
302	302	== 5.1 Application EUI ==
...	...	@@ -315,7 +315,6 @@
315	315	)))
316	316	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
317	317
318		-
319	319	== 5.2 Application Key ==
320	320
321	321	Feature: Get or Set the Application Key.
...	...	@@ -332,7 +332,6 @@
332	332	)))
333	333	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
334	334
335		-
336	336	== 5.3 Application Session Key ==
337	337
338	338	Feature: Get or Set the Application Session Key.
...	...	@@ -351,8 +351,6 @@
351	351	OK
352	352	)))
353	353
354		-
355		-
356	356	== 5.4 Device Address ==
357	357
358	358	Feature: Get or Set the Device Address.
...	...	@@ -798,7 +798,7 @@
798	798
799	799	)))
800	800
801		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
802	802
803	803	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
804	804
...	...	@@ -999,12 +999,10 @@
999	999	**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1000	1000	)))
1001	1001
1002		-[[image:image-20220526162535-1.png]]
	994	+[[image:image-20220511120050-1.png]]
1003	1003
1004	1004	(((
1005	1005	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1006		-
1007		-
1008	1008	)))
1009	1009
1010	1010	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1106,6 +1106,6 @@
1106	1106
1107	1107	Same as:
1108	1108
1109		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1110		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1111		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1099	+* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.1AdaptiveDataRate]]
	1100	+* AT+DR=5 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
	1101	+* AT+TXP=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]