Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 1 removed)
  • image-20220526162535-1.png

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,9 +20,9 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27	27	= 3. Support End Node and firmware version =
28	28
...	...	@@ -135,7 +135,6 @@
135	135	* **Example 1**: Downlink Payload:** 0100001E** ~/~/ Set Transmit Interval (TDC) = 30 seconds
136	136	* **Example 2**: Downlink Payload:** 0100003C** ~/~/ Set Transmit Interval (TDC) = 60 seconds
137	137
138		-
139	139	== 4.2 Reboot End Node ==
140	140
141	141	Feature: Reboot End Node to perform a new OTAA or ABP Join.
...	...	@@ -171,8 +171,6 @@
171	171
172	172	(((
173	173	If the downlink payload=**04FF**, the end node will reboot.
174		-
175		-
176	176	)))
177	177
178	178	== 4.3 Reset to factory Default ==
...	...	@@ -297,8 +297,6 @@
297	297	OK
298	298	)))
299	299
300		-
301		-
302	302	= 5. Keys, IDs and EUIs management =
303	303
304	304	== 5.1 Application EUI ==
...	...	@@ -317,8 +317,6 @@
317	317	)))
318	318	|(% style="width:305px" %)AT+APPEUI=00 b3 d5 7e f0 00 4d 34|(% style="width:186px" %)Set the Application EUI|(% style="width:191px" %)OK
319	319
320		-
321		-
322	322	== 5.2 Application Key ==
323	323
324	324	Feature: Get or Set the Application Key.
...	...	@@ -335,8 +335,6 @@
335	335	)))
336	336	|(% style="width:441px" %)AT+APPKEY=00 35 55 55 22 23 55 53 43 24 23 42 34 35 35 35|(% style="width:180px" %)Set the Application Key|(% style="width:350px" %)OK
337	337
338		-
339		-
340	340	== 5.3 Application Session Key ==
341	341
342	342	Feature: Get or Set the Application Session Key.
...	...	@@ -800,7 +800,7 @@
800	800
801	801	)))
802	802
803		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
804	804
805	805	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
806	806
...	...	@@ -1001,12 +1001,10 @@
1001	1001	**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
1002	1002	)))
1003	1003
1004		-[[image:image-20220526162535-1.png]]
	994	+[[image:image-20220511120050-1.png]]
1005	1005
1006	1006	(((
1007	1007	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1008		-
1009		-
1010	1010	)))
1011	1011
1012	1012	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1108,6 +1108,6 @@
1108	1108
1109	1109	Same as:
1110	1110
1111		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1112		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1113		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1099	+* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.1AdaptiveDataRate]]
	1100	+* AT+DR=5 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
	1101	+* AT+TXP=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]

image-20220526162535-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-149.4 KB

Content