Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 0 added, 1 removed)
  • image-20220526162535-1.png

Details

Page properties

Content

...	...	@@ -3,7 +3,6 @@
3	3	{{toc/}}
4	4
5	5
6		-
7	7	= 1. Introduction =
8	8
9	9	Dragino LoRaWAN End Node support two types of AT Commands and Downlink Commands:
...	...	@@ -20,11 +20,10 @@
20	20
21	21	* For AT Command , See Devices User Manual for Device. The user manual can be found in each product page of [[Dragino Official Website>>url:http://www.dragino.com/]]
22	22	* For LoRaWAN Downlink: The gateway transfer downlink command in HEX format. This page shows the HEX format downlink code for each command. but some servers use base64 as downlink code. Below are reference for how to use downlink command:
23		-** Use HEX format to send a downlink: [[TTN v3>>doc:Main.Notes for TTN.WebHome]]
24		-** Use Base64 format to send a downlink: [[Chirpstack>>doc:Main.Notes for ChirpStack.WebHome]].
25		-** See use note for more serves [[Servers Note>>doc:Main.WebHome]](IoT LoRaWAN Server)
	22	+** Use HEX format to send a downlink: [[TTN v3>>url:https://wiki.dragino.com/index.php/Notes_for_TTN#Send_Downlink_message]]
	23	+** Use Base64 format to send a downlink: [[Chirpstack>>url:https://wiki.dragino.com/index.php/Notes_for_ChirpStack#Downlink]].
	24	+** See use note for more serves [[Servers Note>>url:https://wiki.dragino.com/index.php/Main_Page#Use_Note_for_Server]]
26	26
27		-
28	28	= 3. Support End Node and firmware version =
29	29
30	30	(% border="1" style="background-color:#ffffcc; color:green; width:966px" %)
...	...	@@ -98,8 +98,6 @@
98	98	)))
99	99	)))
100	100
101		-
102		-
103	103	= 4. System Management Commands =
104	104
105	105	== 4.1 Change Uplink Interval ==
...	...	@@ -173,8 +173,6 @@
173	173
174	174	(((
175	175	If the downlink payload=**04FF**, the end node will reboot.
176		-
177		-
178	178	)))
179	179
180	180	== 4.3 Reset to factory Default ==
...	...	@@ -796,7 +796,7 @@
796	796
797	797	)))
798	798
799		-== 7.11 Receive Delay2 ==
	793	+== 7.11Receive Delay2 ==
800	800
801	801	Feature: Get or Set the delay between the end of the Tx and the Rx Window 2 in ms
802	802
...	...	@@ -997,12 +997,10 @@
997	997	**AT+RX1TWO** is theRxSingle timeout value of receive window 1. If it is not set, then the queriedvalue is the default value. If it is set, then the queried value is the setvalue. AT+RX2TWO is thesame as above. The definitionof RxSingle timeout is as described in the following paragraph.
998	998	)))
999	999
1000		-[[image:image-20220526162535-1.png]]
	994	+[[image:image-20220511120050-1.png]]
1001	1001
1002	1002	(((
1003	1003	Increasing thisvalue is equal to extending the time that the receiving window is opened, butthe corresponding power consumption will also increase. Properly increasingthis value can increase the success rate of the downlink.
1004		-
1005		-
1006	1006	)))
1007	1007
1008	1008	== 7.21 Get or Set RXwindows2 timeout ==
...	...	@@ -1104,6 +1104,6 @@
1104	1104
1105	1105	Same as:
1106	1106
1107		-* AT+ADR=0  [[Reference>>||anchor="H7.1AdaptiveDataRate"]]
1108		-* AT+DR=5  [[Reference>>||anchor="H7.4DataRate"]]
1109		-* AT+TXP=0  [[Reference>>||anchor="H7.14TransmitPower"]]
	1099	+* AT+ADR=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.1AdaptiveDataRate]]
	1100	+* AT+DR=5 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.4DataRate]]
	1101	+* AT+TXP=0 [[Reference>>http://8.211.40.43:8080/xwiki/bin/view/End%20Device%20AT%20Commands%20and%20Downlink%20Command/#H7.14TransmitPower]]

image-20220526162535-1.png

Author

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Xiaoling

Size

...	...	@@ -1,1 +1,0 @@
1		-149.4 KB

Content